Find a Window Installer you can trust near you.

Whether you’re hiring a professional to replace your double glazing or are considering DIY, it’s a good idea to know how to fit a double glazed window.

You need to start by assembling your window. Fit any handles and cut the outer sill to size by measuring the outer wall depth. Then, screw the outer sill to the window frame and attach the frame fixers. Screw the ventilation grilles onto the inside of the frame and fix the vents on.

Next, you need put the window into place, using spacers to wedge it in. Use a spirit level to check it’s level horizontally and vertically, adding extra spacers if needed. Then, fix the frame into place at each fixing point using a drill, wall plugs and screws. Measure and cut the interior sill, and check that it’s level, adding spacers if needed. Then fix it using screws, masonry nails or adhesive.

Finally, fill in any wide gaps with foam filler and small gaps with sealant. You can get interior and exterior trims to cover these up, making your window look neat and professional.

Ultimately the double glazing company you use is responsible for the quality of work and to ensure your windows are of an excellent standard. This is why it’s important to get a warranty and use a Fensa registered installer. If problems emerge within a couple of years then it’s likely the installation was of a poor standard.Contact the double glazing company and have the issue repaired or new windows replaced. This doesn’t matter if you received a discount of free windows as part of the deal. As long as you entered into a contract the company is obliged to restore the windows.

It depends on a few factors whether a new double glazed window will look different to existing ones. If your existing windows are very old, perhaps 10 years or more, then it’s likely that there will be some small differences.

The first thing to remember is that your double glazing is exposed to the elements as soon as it’s installed. So over time, unless you’re very good at cleaning and maintaining your windows, they’re likely to look a bit dirty. Window frames that are south-facing may also become slightly discoloured from the sun, so if you install a new window right next to it you might notice a difference.

Also, there have been lots of technical advances in windows over the years. If your existing windows are significantly older, you might notice a difference in the handles on openers, and if your existing windows were installed before 2010 they might not have trickle vents, which is an extra strip on the inside of your window to keep air flowing through your home. While it’s not a legal requirement for replacement windows to have trickle vents if the original one didn’t, it’s a good idea to have them installed as they help prevent condensation and mould.

The only truly noticeably different elements to a new double glazed window compared with existing ones are likely to be on the inside, which might not be a problem for you if you only have one window in a room. However, if you know the brand of your existing windows, you can ask your window installer if they can source the same ones. Even if they’ve been updated slightly, the difference should be minimal.

Double glazed windows are better than single glazed generally because they are more energy efficient. The clue’s in the name – double glazed windows have two panes of glass while single glazed windows only have one. In double glazed windows, there is a space between the two glass panes. This space is filled with inert gas or a tight vacuum, which helps to provide an extra level of insulation. That means that heat won’t escape your home easily, nor will it creep in, so you can keep your home at a more comfortable temperature.

The extra pane of glass also helps to increase your home’s security. Single glazing is pretty easy to smash through, whereas it will take much more effort to smash double glazing and will create more noise, so burglars might be put off.

Another reason why double glazed windows are better than single glazed ones is that they help to reduce noise. Of course, if you live by a busy road you’ll still hear some traffic noise, but it can be significantly reduced buy double glazing. In the same way that the inert gas in the middle of the two panes keeps heat in and the cold out, it also helps keep noise out.

With double glazing, you’ll also notice much less condensation. With single glazing, it’s common to see condensation on the inside of the windows, especially when the heating is on. This is because the outside of the window is cold, but the inside is warm. With double glazing, the insulation between the two panes stops there being such a difference in temperature between the inside and outside of the window.

Just like every other thing in your house, your double glazed windows have an expected lifespan attached to it as it gradually becomes less functional and less efficient over time. Although there are actually top quality windows which are able to last a very long time, but the fact still remains that nothing can stand the test of time or last forever. Even the best quality double glazed windows will eventually need to be replaced at some point. So exactly how long do double glazing windows last before need a replacement?

To make it brief, most double glazing window units are typically expected to last an average of 20 years. This number of years can, however, vary within the range of 10 to 35 years based on the several factors such as the type, quality of materials as well as installation and where the windows are located.

The reason for the depreciation in double glazing windows is, over time, the windows may be subjected to some wear, tear as well as all kinds of minor damages which includes gas filled insulated glazing unit slowly and gradually leaking. According to the Centre for Sustainable Energy, the evaporation of 25 percent of gas will ultimately minimize the windows’ thermal performance. And when this occurs, fitting a secondary glazing measure or replacing the windows should be put into consideration.

Another factor leading to the gradual depreciation in double glazing windows over time has to do with condensation. When the window collects between the layers of glass due to the failure of the seal of the perimeter and the saturation of the desiccant, can only be solved by IGU replacement.

And finally, the ravages of time also has a way of taking its toll on double glazing windows. This can happen in so many ways such that the window becomes a lot less efficient and later needing to be replaced.

Most window installers will be able to provide you with one double glazed window and fit it for you. If you’re replacing one double glazed window in your home, ask them to try and source the same windows that you already have or find one that’s very similar. Externally, you probably won’t be able to notice the difference, but if your existing windows are very old there may be some exterior discolouration and the locks and handles might look slightly different.

If you want one double glazed window so you can fit it yourself, there are lots of online companies that can supply you with one window. However, window fitting is a skilled trade and you might want to consider whether you have the right tools and experience to fit it yourself. Of course, you’ll save money on installation costs, but if something goes wrong, you might end up shelling out to get it fixed anyway.

The other thing to consider is that any replacement windows need to be certified that they meet Building Regulations. If you fit the double glazed window yourself, you’ll need to apply to your local council building control officer to get a certificate that confirms that you fitted the window within the regulations. You’ll have to pay a fee for this, and it will be even more expensive if Building Control say that the window hasn’t been fitted within the regulations and you have to start again.

The alternative is to ask a reputable window installer that is registered with a self-certification scheme, like FENSA, to install the window. That means that they can self-certify that the window meets building regulations once they’ve finished the installation.

If you’ve got a problem with condensation and don’t have double glazing, you should find that getting new windows will help. Condensation is caused by warm air meeting a cold surface which then turns into water droplets. With two panes of glass, less heat will escape from your home and keep the window warmer, meaning when steam from the bathroom or kitchen touches your windows there should be less condensation.

Did you just purchase a double glazed window and confused about how to have it installed? Fitting the window yourself can be quite easy with the help of this step by step guide. However, if you lack proper training or experience, we’d recommend you reach out to a trustworthy professional who can guarantee the best results for help. That said, now let’s take a look at the process.

• Remove the old windows by detaching the old beading and glass window safely. Then make some interval cuts using a hand saw before using a crowbar to pry it out.

• Cut the external double glazed window seal. Once done, take a measurement of the window area’s width once empty. Then transfer the measurement to the window sil to face outside and cut using a handsaw.

• Seal the window sil. Add a bead of clear silicone along both inside lip as well as the centre to seal the sil.

• Screw the double glazed window to the sil. Position the window on the top of the lipped section that was siliconed. Then pre-drill them together and screw in three places. You should make sure the screws do not go totally to the sil’s bottom.

• Install the double glazed window. After successfully screwing the double glazed window to the sil, you can now fit in the double glazing. Make use of packers to make sure it’s even in the slot.

• Screw the uPVC window to the wall. If you’re happy and satisfied with the position of the window, you can then pre-drill through the frame of the window and the brick wall. Once done, simply screw it in place using masonry screws or Spax screw as they do not require crawl plugs in bricks.

• Seal around the window. To do this, simply fill any gaps with expanding foam, wipe out the excess and seal with silicone.