Ground Source Heat Pump in Lytham St Annes

If you’re thinking about the possibility of installing a ground source heat pump in your home, then it’s normal to consider how efficient they’re in heating up a house before going ahead to make a purchase decision. In this article, we are going to address this question to help you make an informed purchase decision.

We know you’d prefer a single, accurate answer to this question, but the fact is, there are several influencing factors that can play a key role in the efficiency of a ground source heat pump installation. These factors include whether or not the property is well insulated, the fitting of a well designed system and the quality of its installation, the heat source that’s being used as well as the heating distribution system and its size ( under floor heating or radiators ).

The Coefficient of Performance ( CoP) measurement is used to imply the efficiency of a heat pump. This is basically the ratio between the amount of heat energy generated by the ground source heat pump and the amount of electrical energy or fuel it consumes. Therefore, the Seasonal Coefficient of Performance ( SCoP) is usually taken as a realistic measurement to cover throughout the year as its based on CoP at varying conditions as well as a standardized climate.

You must, however, note that there is no established Coefficient of Performance for ground source heat pumps as they can be influenced by a lot of factors as well as testing conditions. When they’re properly fitted, ground source heat pumps can achieve a quite high Coefficient of Performance.

Generally, a ground source heat pump can generate about 3 to 4 kilowatts (kW) of heat for every 1 kilowatt to electricity or fuel it consumes. It’s able to achieve a higher efficiency when compared to its counterparts by using the freely available heat energy from the ground.

If you’re considering installing ground source heat pump, it’s likely you’re also wondering just how deep it’ll go into the ground to be efficient. Well, the initial step to take while determining the ground source heat pump’s design is to research the different options available to reduce the space heating as well as hot water demand. To achieve this, there must be an accurate measurement of energy efficiency which is usually done by getting an Energy Performance Certificate ( EPC) . This is helpful as such that it helps to identify the most suitable or the right size of heat pumps which will help reduce the consumption of energy, heat loss as well as hot water needs of the house.

Generally, ground source heat pumps are usually more compatible with new builds against retrofits. What’s more? The heat pump has two different types of loop systems :

✓ The open loop system and;

✓ The closed loop system.

The open loop system absorbs water from the ground and transfers this ground water via a heat pump to where it carries out the extraction of heat. Meanwhile the closed loop system extracts heat from the ground and incorporates a continuous loop of piping that’s linked to the indoor heat pump. There are a few types of closed loop system, these includes:

✓ The Horizontal Ground Source Heat Pump. This is installed in horizontal trenches of about 1 to 2 metres deep. This is more common in areas where land is readily available.

✓ The Vertical Ground Source Heat Pump. These boreholes are a more costly option but it’s also the best option when land is not readily available for horizontal installation. The insulation hole is dug at a minimum of 6 metres into the ground, while the entire piping will be at a depth of about 50 to 150 metres based on your home’s heat requirements as well as the ground’s composition.

So do you wish to take advantage of the heat generated by the ground to warm up your home by getting a ground source heating pump? If yes, then you’d also probably be wondering how much a ground source heat pump is going to cost so you can set a budget and start planning.

Installing and running ground source heat pump can cost between the range of £600 to £700 to run on an annual basis, meanwhile it can cost you within a range of £13,000 to £19,000 to have installed. However, you should take note that these prices can be by varying influencing factors such as the size of the installation as well as any other extra work that may needed to complete the job.

When it comes to estimating the time it takes to recover the initial cost of the system via energy savings, nothing is certain as this can be very hard to determine or predict. The main reason for this is due to the fact that it’s dependent on the efficiency of your heating system, the type of system you’re replacing ( whether or not you qualify for Renewable Heat Incentive -RHI payments ), the efficiency of your home’s insulation, how efficiently the system’s controls are being used and how the heat generated from the ground source heat pump would be put to use. However, to figure out how much you’ll save, the type of fuel replacing is perhaps the most essential. For a four bedroom detached house, you can save between a range of £1,200 to £1,300 for a LPG fuel replaced, £1,400 to £1,500 for an electricity fuel replaced, £600 to £700 for an oil fuel replaced and finally, £200 to £300 for a solid fuel replaced.

When people think about heat pumps, they’ll automatically have the believe that a swimming pool will require a big heat pump. Since the swimming pool has a large volume of water, then warming such a volume will require a large ground source heat pump because that volume is much larger than the normal domestic hot water tank, right? Well, that point of reasoning does seem logical especially with the information almost everywhere that ground source heat pumps are usually less efficient when it comes to heating hot water for home’s use. However, the fact is there are also some things to put into consideration that also works in favour of the ground source heat pump.

First and foremost, you should know your domestic hot water will typically be heated to a much higher temperature when compared to your swimming pool. Since you wouldn’t be using the water to disinfect your bathroom or doing your dishes in your swimming pool, then the temperature can be much lower. In fact, it’s much more comfortable and enjoyable to heat to a typical “swimming pool temperature than having it at a hot bath temperature. If you’ve ever wandered into a really hot swimming pool, you wouldn’t need any introduction to the painful discomfort that comes next.

As a result of this low temperature, your “tiny heat pump can operate a in a more efficient way which makes the use of ground source heat pumps a viable swimming pool heating option. What’s more? The ground source heat pump works for a swimming pool just like any any other application - moving the heat from the region of a warmer temperature to the cooler temperature region.