Soffits & Fascias in Argyll

The soffit and fascia is the outdoor underside region of your roof which would need to be repaired or replaced when it’s in a critical condition. Your soffit and fascia may actually require more frequent replacement or repair depending on the material that the soffit or fascia uses. If you notice your soffit and fascia needs to be replaced, then you’d probably also like to know how much it going to cost. Well, you’ve come to the right place! The price to replace a soffit and fascia can vary significantly which can be a bit annoying when you’re trying to calculate the overall cost you’ll be expected to pay.

The price of a soffit and fascia is based on the following variables:

✓ The materials you wish to use for the new fascia, soffit and guttering

✓ The type of the property. For instance, semi detached houses may come at a lower price due to the less roof space they require when compared to their counterparts, which can reduce the cost of replacement.

✓ If you’re going to also replace the gutter at the same time will also increase the cost of replacement.

✓ The current overall condition of the roof. For example, if you also have broken or slipping roof tiles, the soffits and fascias can be more difficult to replace, hence, increasing the cost of the project.

Generally, the average cost of fitting soffits and fascias as replacement options for your homes will range between £1200 - £3,000. What’s more? Soffits and fascias normally have a per metre cost. The average price of soffits and fascias per metre can range between £100 to £130 when you opt for a white uPVC option.

Having ventilation in the roof void is a requirement for building regulations approval. Fitting ventilated soffits is the typical way that this roof ventilation is achieved. If you do not have roof ventilation, you may find that your roof void has problems with condensation or overheating.

Fascias and Soffits, just like any other components of a home, do not last forever. They can become tired and worn out over time which implies that you’ll have to replace them to prevent further damage. Getting this project completed can be quite costly, but it doesn’t have to be. Fitting soffits and fascias is very simple task which will leave you with both a modern and contemporary styling which requires little maintenance and also more savings. What’s more? You don’t have to worry about repainting the fascias and soffits on an annual basis, all you need to do is a gentle wipe down of the features with a damp cloth to have them look good.

If you’re a competent DIYer and confident enough to pull off this task, then all the better. However, if otherwise, we’d strongly recommend you hire the services of a reliable contractor who can guarantee the best results for help. Here are the steps you can follow to fit your fascias and soffits.

Fascias ( a 18mm fascia board)

✓ This is designed for a direct fix without a need for a timber substrate. Simply secure them directly to the rafters with the help of 2 x 65mm a4 stainless steel fixing nails per rafter.

✓ Ensure that the rafters are level.

✓ Cut the boards back 5mm per edge to enable expansion where any white corner trims, joint trims or angle trims is needed.

✓ Secure the guttering to all third rafter.

Soffit ( 9mm soffit board)

✓ Ensure that the preservative treatment to the structural timber has dried out.

✓ Fix all utility boards of about 100mm to 605mm in width at a maximum of 60mm centres.

✓ If ventilation is needed, there are some soffits that are available in 150mm to 605mm widths and also provides the 10mm air gap needed for roof with a pitch above 15 degrees

It may be shocking a whole lot of people would not be able to point out fascias and soffits on a building despite the fact that they’re an essential part of the roof. To give you an idea, they’re simply used to cover the roof beams’ ends that comes out of the wall from underneath of the roof. The board that runs vertically just below the roofline is the fascia board, which is also the long length of UPVC. Therefore if you look at the gutters located in the front of house, the board behind is called the fascia board. However, soffits runs horizontally from behind the gutters to the wall of a building, so if you walk close to a house and look up, you’ll identify the soffits. They’re done to cover the gaps between the wall house and the gutters. The main function of both soffit and fascia is to divert water away from your roof as well as walls.

Fascias and soffits were usually made of wood before UPVC came along. And as a result, they only require little maintenance, no more warping, painting or cracks unlike the wooden ones. However they also can’t last an eternity, so when the time comes and you need to replace your soffit and fascia, you’ll probably want to know just how much it’s going to cost.

Unfortunately, there’s no way to calculate an accurate cost for fascias and soffits as there are too many variables to put into consideration. These includes the type of fascia and soffit you choose as well as the size of your property. However the average cost to replace a three bed semi-detached house’s fascias and soffits is within the range of £1200 to £1500 or even more if you’re staying in London or in a larger detached building.