Find a TV Aerial Installer you can trust in Tyne And Wear.

Your TV and aerial need to be connected by coaxial cable for your TV to work. Most properties have wall mounted connection boxes – similar to electrical plugs – that you can simply plug your TV into. If you don’t have a cable, it’s easy to pick up one from most DIY shops.

If you’re installing a new outside aerial, you may be able to reuse the old cable. If you can’t, you’ll need to route a new one down from your aerial to any sockets you need. Coaxial cable can be routed down the exterior of your property, through loft spaces, under floors and along skirting boards.

If your TV picture is pixelated, poor quality, or cutting out, there may be a fault with your aerial or the cables connecting it to your TV. Also your aerial may not be located in the correct place. An experienced aerial company can carry out a survey to discover the fault.

Satellite TV is a service that provides its customers with a wide range of TV channels by transmitting signals from a communications satellite. Users around the world can pick it up using a satellite dish mounted on their property and connected to their TV. Satellite TV is particularly useful for viewers who live out of aerial and cable TV range in remote areas.

Generally speaking, you do need an aerial if you have a smart TV. This what will enable you to watch live TV. However, if you’re not bothered about live TV, and just want to use services like Netflix, Amazon Prime and Youtube, you don’t normally need a TV aerial. This is because these services use the internet instead.

If you’re looking at the possibility of installing a satellite dish on your chimney, then you’ve come to the right place! First and foremost, it should be noted that chimney mounts are mostly incorporated for individuals who desires the installation of an antenna at the highest point of their roofs without having to drill holes in the roof. This is quite popular as they’re able to ensure an easy installation and also works incredibly well for several antennas. What about satellite dish? Can it also be mounted on a chimney? Let’s take a look!

The short and simple answer to this question is yes, a satellite dish can be installed on a chimney. However, it must be said that this installation is not advisable. Unlike antennas, satellite dishes are aimed much more precisely. While antennas can be positioned as far as 15 degrees off the main aim before the reception is affected, satellite dishes, on the other hand, need to be positioned about one half of one degree in order to allow for a good operation. This is mainly because the broadcast tower you’re aiming your antenna at is, at most, 75 miles away compared to satellite dishes which are aimed at broadcast towers which are at least 22,000 miles away and that’s even if you happen to be directly under one.

Installing a satellite dish on a chimney will make it difficult for you to get it secure enough to have it properly aimed. This isn’t to say it won’t work at first, but most times, winds will probably drive the satellite dish off the target in little time.

Not if your current aerial is in good condition and receives a good signal. If you don’t currently get a good signal, you may need to upgrade or relocate your aerial to receive HD channels or if your TV is not HD ready. You may need to upgrade your television if this is the case.

Does your old TV aerial cable have a cut or tear in line? Well, good news is, you don’t have to discard it. When such problems occur, they can lead to loss of conductivity or interference which results in weak or poor reception or even none at all. With a few easily accessible coaxial repair tools which can be obtained from local stores, repairing your aerial cable can require a much less effort than you think. In this post, we’re going to take you through the TV aerial cable repairing process. Let’s take a look!

• Identify the part of your coaxial cable that needs to be repaired. Incorporate wire cutters to make a clean cut across the damaged cable portion.
• Close the RG-6 labeled groove of the crimping tool an inch down the cable and make a complete cut around the exterior part of the cable.
• Cut the exposed aluminum braiding around the insulation to leave the copper filament above the cut portion which is usually surrounded by a white PVC insulation.
• Using the part of the stripping tool labeled “inner, cut between the insulation down to around 1/3 inch. Once done, twist the stripper around the section to get a clean cut and take off the portion that is cut.
• Identify the copper filament positioned at the middle of the cable and surrounded by insulation and thread it through the twist-on connector’s base.
• Strip the damaged coax cable’s other end and add a twist-on connector to it.
• Use a coupler to connect the two repaired cables. To do this, simply screw one end of the first cable to one side of the cable coupler and do the same to the second cable to the other side of the coupler

Yes, an aerial could be installed in your garden or on outbuildings. This will depend on the strength of the signal in your area. A professional aerial installation company will be able to advise you on the possible locations for an aerial on your property.