Find a Builder you can trust in Tarbert.

Generally, extensions can be a very tricky undertaking - where it can be quite difficult to have a clear comprehension of the rules, regulations as well as costs. Therefore before you rush in to kick start your ground floor extension project, it’ll be wise to get a good grip on the cost. In this article, we’re going to give you a rough estimate of the cost of a ground floor extension. Let’s take a look!

Just like several other home improvement projects, the cost of constructing a ground floor extension is based on a number of things which includes the size, materials used, your location, the quality of the tradesmen or company hired and lots more. For instance, if you happen to reside in London, the cost of your ground floor extension is going to be a lot higher than the other regions.

The single cost of a ground floor extension should fall within the range of £1,500 per square metre to about £2,000 per square metre. However, if you happen to live in London or the South East, this price can reach up to £1,900 per square metre to about £2,400 per square metre. These prices are for good quality ground floor extensions only. Basic or low quality extensions would naturally cost less while superior quality extension will cost more.

Now looking at the size of the ground floor extension, if you’re looking for a size of about 5m x 5m, you can expect to pay a price within the range of £32,000 to about £36,000. And as usual, in London or the South East, this price can reach up to £50,000 or even more. And that’s just for constructing the extension. If the other relevant costs like the 10 percent to 15 percent professional fees for the architect, planning application (if needed), building regulations and more, the price goes up.

When it comes to laying of bricks, it is essential to get the right mortar mix. It is vital, be it for construction or maintenance projects, so far mortar is required. There are several materials incorporated in getting mortar which includes both cement and sharp sand, soft sand or plasterer’s sand and lots more. Here, we are going to look at the right ratio for cement and sand mix in bricklaying.

Cement include ingredients such as iron, aluminium, as well as silicon and it is mainly used for mortars like aerated cement mortar, Portland cement mortar and gauged mortar. Sand, on the other hand, comes in different forms such as sharp sand, soft sand and plasterer’s sand. The sharp sand consists of a larger grain size than the others and is usually incorporated in the construction areas that requires more strength as well as flexibility. Soft sand is the most common one used in mortar and it’s also referred to as bricklayers’ sand. These are used to make all types of mortar. Finally the plasterer’s sand which neither has the sharp sand’s coarseness nor the fineness of the soft sand, but can also be used for any form of mortar.

Cement and sand mortar is used for a plethora of bricklaying jobs serving as a glue for bricks, walls and pillars, while also repairing or maintaining old listed buildings. The preferred ratio here is 1:3 to 1:5 of cement and building sand. Meanwhile, to get a sand cement mix, essential materials that are required includes water, soft building sand as well as cement. However, you must also note that a sand and cement mortar is not used for structural projects, rather a concrete ratio is used.

If you’re planning to construct a kitchen extension on your property, one of the first things that comes to mind is whether or not you’ll require a planning permission before you proceed. Generally, kitchen extensions are normally classified as permitted development which allows you to carry out your project without any interruptions from the law or your local authority. In other words, if your extension is meets up with the guidelines of the permitted development rights, you won’t have to apply for a planning permission. However if otherwise, you’ll have to apply for a planning permission to your local council and may require additional reports. And regardless of your position, you’ll always need building regulations approval before you can carry out any kitchen extension project. It may also be required that you’ll have to issue a part wall notice if you’re to build on or close to the boundary with a neighbour.

If you don’t want to go through the hassle and stress involved in applying for a planning permission with your local council, then you must ensure the following:

✓ Your kitchen extension must not be over half of the area of land around your main house.

✓ The kitchen extension must not be side elevation onto a highway or forward of the principal elevation.

✓ The extension must not be taller than the highest part of the roof.

✓ The height of your kitchen extension must not go beyond four metres.

✓ Kitchen extension that’s more than one storey must not go exceed the rear wall of the main house by more than three metres.

✓ Two storey kitchen extensions must not be closer to rear boundary by anything less than seven metres.

✓ The kitchen extension must not include balconies, verandas or any raised platforms.

How To Plasterboard A Brick Wall

Do you want to cover your brick wall with plasterboard? The key to success here is the preparation. You must ensure that brick wall is prepared well enough to receive the plasterboard. To get started, there’s the need to attach wood furring strips to the wall which serves as studs in a wood frame structure. This way, the plasterboard will be prevented from getting in touch with the brick. You can always hang pictures or any other forms of decoration in between the gap between the walls. Let’s have a look!

lAttach Furring Strips

• Get a 2 inch by 4 inch wood stud and apply a bead of construction adhesive.

• Using a masonry bit, drill a pilot hole through the wood stud’s base as well as the brick wall.

• Hit a 3 inch fluted nail through the hole using a sledgehammer

• Using a construction adhesive, bind a horizontal 2 inch by 3 inch stud to the upper edge of the wall.

• Using an adhesive, bind the length of a 2 inch by 3 inch stud on its wide side.

• Use a masonry drill to drill a hole on the wood stud and 1 1/2 inches into the brick wall.

• Hit a 3 inch fluted nail through the pilot hole.

lApply Plasterboard

• Hold a plasterboard sheet against the furring strips.

• Use plasterboard screw to hold the drywall sheets in place.

• Use fibreglass to cover the joints where the two plasterboard sheets meet.

• Use a thin layer of the joint compound on the tape. Once done, screw it using a 6 inch taping knife, then allow to dry overnight.

• Use a sandpaper to smooth the joint compound.

• Use a fresh coat of the joint compound to block the holes and joints. Once done, allow the compound to dry.

• Use a light sandpaper to smooth the final coat.

Plasterboarding a brick wall is a simple task but the preparation part must be done right to protect your investment. Therefore, we’d recommend you hire the services of a skilful professional, who can guarantee the best results especially if you lack enough training and experience to carry out a DIY project.

A front porch is a glorious addition that would be a blessing to have in any home. It gives you a good floor space to enjoy your neighbourhood as well as your surroundings in the cool atmosphere of the outside living space. The question however is, how do you build a porch? Constructing the structure can be a very challenging task but with proper guidance and lots of practice, you can also be a skilled porch builder. To protect your investment, it’s advisable to hire the services of a professional for help with your porch especially if you lack proper training and experience. This way, you’ll get to save time and money. This guide is prepared to give you some insight into the porch building process.

lAssess Your Location

• Consider the location before proceeding with the project. It’s essential to select a location that’ll reduce the sunlight coming in.

lPlan The Materials Required For Your Porch

• You’ll have to decide the type of porch you’ll be going for. For example, your porch can be built out of wood, composite decking or if it’s going to utilize some stone flooring, brick or even tile.

lBuild Your Porch Foundation

• Dig the foundations deep to ensure stability while also putting in mind any pipework or cabling

• Fit a damp proof course

• Add the subfloor - this can be concrete or timber

lStart To Lay The Brick And Floor

• Lay the bricks evenly up to the DPC level

• Lay the floor

• Add the flooring protection

• Once done, you can lay the bricks to the window level

• You can fit in a window sill if required before proceeding the brick and block work until it reaches the roof timber’s height

• Fit the linter when you get to the top of where the window will reach.

lConstruct The Roof

• Build a timber framework

• Fit a breathable roof membrane

• Install the roof battens and lay the roof tiles.

• Add gutters

Are you considering converting your garage into a more usable space in your home? If yes, then you’d probably want to know if you’ll require building regs before converting the garage. The answer to this question is yes. Although you may not require planning approval to convert your garage into a more usable space, but you’d usually need approval under the Building Regulations.

When re-structuring your garage into a habitable space, the following should be taken into consideration: structural alterations, ventilation, moisture proofing, insulation, fireproofing, escape routes as well as the submission of a building building notice or full plan application to the local council in order to inform them about the planned project.

• Walls

You’ll require an approval if you plan to infill the garage door with a window and a new wall. This is because the garage may have been built of a shallow slab which implies that a new foundation would be needed for the new wall construction.

• Floor

Even though there’s a high possibility that the garage floor is strong enough for domestic use since its designed to withstand the weight of vehicles, you may however need to upgrade to make sure it suitable for both thermal insulation and damp proofing. In addition, there may also be the need to to alter the floor level in such a way that it matches that of the remaining parts of the house.

• Ventilation

According to the Building Regulations requirements, there’s a need for adequate ventilation for each individual rooms which includes garage conversions for general health purposes. What’s going to determine the ventilation level that’ll be required is the frequency at which the room is used. Ventilation can be provided through purge or simply opening the window or via trickle ventilation.

External cladding will have an impact on a damp problem. However, it’s important that cladding is the last part of a damp treatment, as installing cladding over a damp wall will make the problem worse. Do not cut corners or try to remedy a problem with the cheapest solution, a damp proof course may need to be put in place before cladding.

It depends on the style and size of the conversion, but in general, a loft conversion will take between 1-2 months. A loft conversion is a substantial building project, and plans will need to be drawn up. This may add to the time it takes to complete your loft conversion.