Find a Builder you can trust in Largs.

Cutting a plasterboard is a relatively simple process requiring only some basic tools. Unfortunately, the lack of knowledge serves as big deterrent for many people who wishes to put it to good use. Plasterboard can actually be sawn using an ordinary timber saw that’s fine-toothed to get a cleaner edge. However, the basic tools you may also need includes a sharp knife (Stanley Knife), pencil, a fine sandpaper, a straight edge and measurement tape as well as a wall board saw. Let’s have a look at the cutting process!

• Firstly, you need to put the plasterboard sheet flat on a firm surface.

• Use the tape measurement to measure the cut you wish to make.

• With the help of a pencil, simply mark out the part you wish to cut on the plasterboard’s front side.

• Once marked, place a spirited level over the marked spot on the plasterboard sheet you want to cut.

• Cut a shallow mark into the plasterboard sheet using the Stanley Knife to cut along the edge.

• The cut should be slow and gradual to ensure you do not wander off the edge of the marked area.

• Once the shallow cut has been made, turn the plasterboard sheet on its edge and deliver a quick and sharp push towards the plasterboard’s back and on one side of the cut.

• Place the plasterboard sheet backing against a flat surface ensuring the line of the cut is over an edge. Once done, give a quick and sharp push towards the back of the plasterboard sheet and on the part of the board is reaches beyond the edge.

• Using a fine sandpaper, remove all forms of paper burrs.

The process of cutting plasterboard requires a lot of practice. If you lack the training and experience, the cutting process is best left to a proficient professional who can guarantee the best results the first time and save you some additional costs due to potential damages.

Did you try rendering a wall but it doesn’t turn out the way you would have hoped for? Or perhaps you’ve been watching your wall render gradually deteriorate over time. Regard of your purpose, learning how to repair render cracks on wall is usually a great skill to have with your home maintenance in mind. However, whenever these crack are too large or difficult, we’d recommend you call in a reliable professional who can guarantee the best results for help. In this guide, we’re going to take you through the wall render repairing process. Let’s have a look!

No matter how solid a building material is, over time it’ll yield to the elements. When it comes to wall rendering it may be a case of too much sunshine or a costly mistake in the application process, but in truth, it cracks just because it cracks.

In order to repair render cracks, you’d have to start with a removal of damaged or cracked render. You’ll have to remove all the render or just a small section depending on the area you’re working on. If you’re able to clean all of the existing render as well as the paint over it all (both old and new), then removing a small section would work better as it makes it look neat and redone. Upon the removal of the existing render, the next important step would be to remove all loose material as well. Once done, you can then leave for up to 2 days to allow any trapped moisture to come out. Unfortunately, if the rains you’d have to wait till that dries too before you proceed.

Once dried, you can buy a pre-prepared render mix which already contains cement, lime and sand. Mix a 20kg bag with 4 litres of water (or check the product instructions and follow strictly), the mix to a fine consistency. Render is quick to dry, so you’d want to apply within 30 minutes of mixing. Make use of a trowel to apply the render on the affected spots and blend with the surrounding area.

Over the years there has been an increase in the recommended thickness of loft insulation by the government. Obviously, the reason behind this is pretty simply - the thicker the layer of your loft insulation the bigger your savings. The UK government is very keen to every house in the country to have loft insulation fitted where possible as it helps to minimize the heating demands of these properties. Households get to benefit from loft insulation in so many ways which includes reduced energy energy bills as well as having a home that stays at a more comfortable temperature for longer.

Generally, for the government energy efficiency is crucial as it implies that the highest demand ( which is usually the time of the day when gas or electricity use is at its peak ) reduces, since each building requires slightly less energy. Overall, that ultimately implies that new power plants don’t have to be built which is some nice cost savings for the government.

In the 1980’s, any thickness of loft insulation from 25 mm to 50 mm was considered the standard. But then, building regulations stated that homes should have as much as 100 mm of loft insulation. Over time, this gradually increased to 270mm for new builds and also recommended for other properties, although not essential. As a result of this, there’s always a need to check how much insulation you currently have in your loft before you decide to purchase more. You may discover that you already have something within the range of 20 mm to 200 mm up there and knowing this and the insulation values will assist in determining how much more you’ll need to purchase, if any at all. You should also note that some modern materials can offer the same thermal insulation whilst not being as thick.

Rendering a house’s external walls is one of the cheapest and most effective ways by which a building can be made waterproof and also good looking. If you’re thinking about rendering your house, figuring out the cost of completion is usually one of the most important things you’ll have to consider before you proceed and if you don’t know where to start, finding an experienced tradesperson who possesses several years of experience as well as the ability to overcome the different issues that he may be faced with while on the project is paramount. If you’re able to get one, however, you should know that they rarely come cheap.

When trying to determine the accurate house rendering cost estimate , a tradesperson will put into consideration a great number of factors. Even at that, a rough estimate still requires both skills and expertise to be able to take into account all the necessary factors. In general, a typical 3 bedroom home in the UK will cost within the range of £4000 to about £5500 for a complete render job on the outside and covering from top to bottom.

Usually, the most important factor which play the biggest role when determining rendering costs is the area that’s going to be covered by the render mix. Professional contractors will provide a quote based on the rendering costs per square metre. Below are some rough estimates of rendering costs of properties depending on their size (without VAT).

✓ For a small mid terrace house of about 40 to 50 square metre, the total rendering cost estimate is £3000 to £4000.

✓ For a large mid terrace house of about 70 to 180 square metre, the total rendering cost estimate is £3000 to £5000.

✓ For a three bedroom detached house of about 100 to 160 square metre, the total rendering cost estimate is £4000 to £5500.

Generally, extensions can be a very tricky undertaking - where it can be quite difficult to have a clear comprehension of the rules, regulations as well as costs. Therefore before you rush in to kick start your ground floor extension project, it’ll be wise to get a good grip on the cost. In this article, we’re going to give you a rough estimate of the cost of a ground floor extension. Let’s take a look!

Just like several other home improvement projects, the cost of constructing a ground floor extension is based on a number of things which includes the size, materials used, your location, the quality of the tradesmen or company hired and lots more. For instance, if you happen to reside in London, the cost of your ground floor extension is going to be a lot higher than the other regions.

The single cost of a ground floor extension should fall within the range of £1,500 per square metre to about £2,000 per square metre. However, if you happen to live in London or the South East, this price can reach up to £1,900 per square metre to about £2,400 per square metre. These prices are for good quality ground floor extensions only. Basic or low quality extensions would naturally cost less while superior quality extension will cost more.

Now looking at the size of the ground floor extension, if you’re looking for a size of about 5m x 5m, you can expect to pay a price within the range of £32,000 to about £36,000. And as usual, in London or the South East, this price can reach up to £50,000 or even more. And that’s just for constructing the extension. If the other relevant costs like the 10 percent to 15 percent professional fees for the architect, planning application (if needed), building regulations and more, the price goes up.

You may need planning permission if you are planning a larger extension. All extensions will need building regulations approval. An architect can assist with this and if planning permission is required. A reputable contractor will also be able to advise you if this is needed as well.

A porch is a small and low structure (with a roof) located at the main entrance of a building or house. It’s typically without a window (although newer variations may come with one) and can either be screened-in or enclosed to prevent unwanted access from insects and extremes in weather. In addition, some homes may have a three-season porch or sun porch. This may be situated by the side of the house and covered by the roof overhang - they’re usually screened in to offer good access all year round.

Generally, porches serve a wide range of purposes. They include:

• Provision of an outdoor living space to relax during the summer months

• It’s an informal extension of the the living room.

• It serves as a great place for social gatherings especially in small towns.

• You can take off your dirty shoes and dry a dripping wet dog before entering into your living room.

• It can be incorporated for relaxation purposes and watching street activities.

• It can serve as a reception area for guests.

• It can also be used for outdoor storage.

Pros & Cons Of A Porch

Pros

• Due to the fact that they’re covered, porches may require little maintenance practices.

• It can go a long way to improves the curb appeal of your property.

• It protects against the extremes of the weather.

• It can be constructed using a wide range of materials.

Cons

• It does not improve the use of the property

• It can be quite expensive to install depending of the material required as well as size of the porch.

• It does not add to the value of the home unlike several other home improvement projects

• It may not be safe to be used by a child or pet.

Being a strong and durable product requiring little maintenance and expected to last over 2 decades, it’s little wonder resin is now a popular material amongst homeowners in the UK to build their driveways. However, there’s always the issue of the driveway fading, cracking or even becoming worn and tired. So is it possible to repair resin driveways? The answer is yes, a resin driveway can be repaired, however the best approach to use largely depends on the issue being faced. As a confident DIYer it’ll be very easy to do, but if you lack the confidence then calling in a professional for help would be a better option. So let’s take a look at how you can repair your resin driveways.

For cracks, the best reparation approach would be to chisel it out. Once done, then you can proceed to breaking the stones to form a rough edge. It’s important to make sure that the matrix of the stone remains unaffected. Make a new mixture of resin bound stone and pack it in tightly to the gap. While doing this, we’ll recommend making use of a plastic trowel to avoid burnishing. This fresh mixture will then create a smooth and perfect surface by interlocking with the edges. You can follow similar procedure for patches but these are larger holes or damages than cracks and as the name suggests are mostly likely to remain noticeable but will prevent further crumbling of your resin driveway.

For homeowners, who aren’t so keen about the patch repairs, you can opt for an overlay especially in the event whereby the majority of the surface has failed. Although many usually shy away from this approach because of the perceived high expenses, but the fact is that the approach is actually cost effective as you won’t have the need to spend more money in the long run.