Find a Builder you can trust in Berriedale.

Render serves two basic functions. One is it’s protective qualities as render acts as waterproof for the wall which enables them breathe by allowing water vapour move from the inside to the outside of the structure while also working to prevent water or rain from finding its way inside the structure. While the second function is the decorative qualities as render is able to provide the structure with a fine finish and colour to make the building a lot more appealing and correcting faults in line and level in the masonry.

If you wish to apply render on your external wall, you’d probably be wondering just how thick the render should be to perfectly serve both of functions. In this article, we’re going to take a look at just that!

For a render thickness, the British Standard Wind Driven Rain Index has come up with 4 ratings which include Sheltered, Moderate, Severe as well as Very Severe. An area with Very Severe rating include South West England. This rating implies that the thickness of the render in this area should be increased to at least 20mm for a direct one coat render applications as well as 5 to 6 external wall insulation base coat applications. And if you happen to reside within one mile of the coast, it’s strongly recommended you incorporate an extra repellent protection like Paraguard AG from Parex.

In general, render that’s prepared on site with cement and sand should be have a minimum of 20mm to 25mm thickness. Although, it should be noted that the quality of the render is based on quality of the sand incorporated, the design mix as well as being largely dependent on how good the mixing technique from the applicator is. The most common reasons why traditional renders fails is due to both poor mixing ratios and low quality materials used.

Pebble dash is an effective way to tune up your house or property as it can go a long way to enhance its curb appeal while also add to its resale value if you should decide to sell later on. Although, it’s highly recommended to leave this task for a reputable specialist, it’s also something that can be done as a DIY task. It must be states that this is a pretty difficult job and even more so if you haven’t attempted it before. In this post we’re going to take you through the processes involved in pebble dashing a wall. Let’s take a look!

• Mix up water with the lime strictly following the manufacturer’s instructions. Once done, leave it covered up to hydrate for at least 24 hours.
• Take one part of the slaked lime and mix it up with cement and six parts sand. This is to give the base mixture required to spread onto the surface.
• Use a trowel to apply the mixture onto the wall. Ensure that the trowel is level and use the edges to make a flat and smooth layer of the mixture on the surface as a base layer. Allow the base layer to dry for up to an hour. Then, rake the surface using a notched trowel and allow to dry for a minimum of 24 hours.
• Rinse and drain your pebbles. Then, set them under the wall you’re pebble dashing.
• Take the top coat of five parts sand and mix with one part cement and one part slaked lime. Use a trowel to apply this mixture over the base layer and smoothen it with the trowel to create a flat and even top layer.
• Spread a plastic sheet beneath the wall you’re pebble dashing to capture any loose pebbles as they fall.
• Grab the bucket of pebbles below the wall and scoop some of the pebbles up using a scoop or trowel. Some will stick and some will fall into the plastic sheet already placed below. Continue throwing the pebble dash until the surface is completely and evenly covered with pebbles.
• Lightly press and fit the pebbles on each section into the wall and leave for at least 24 hours to dry.

Have you decided to improve your property instead of moving? The common problem most homeowners face after deciding to embark on a home extension project is not knowing where to start. In this article we’ll walk you through everything you need to consider and put in place before commencement of your home extension project.

• Is the extension worth it?

Before breaking the bank, you must be sure that the project will add good value to your home. In terms of “value, this is not only limited to the financial gain after disposal of the property, but also several other juicy benefits to be derived from extending your home like an extra living space for the household to spread out and more.

• Do you need a planning permission?

Check with your local authority to determine whether or not you’ll require to submit an application. You can also consult a building expert like an architect for advice.

• What are the building regulation?

Even though planning permission can be dodged, you can not avoid building regulations. These regulations are the set national minimum standards for construction and design which you must comply with to ensure the safety of the individuals in and around it.

• Who will design the extension?

You have to decided whether you’ll hire a professional architect to design the extension or not.

• Who will manage the building work?

If your home extension project is designed and built by a professional company, they’ll be responsible for the management. However, if you decide to use an architect or designed it yourself, you’ll have to hire a main contractor to manage the build.

• How to set the budget?

There are so many factors that can affect the cost of an extension, so it’s better to get the costs from your builder before proceeding.

• Do I need yo inform my home insurance firm?

Absolutely! This is very important as the new extension may affect the rebuilding cost of your property which could have an impact on the policy premium.

• Do I need to inform my neighbours?

It’s very important to discuss your plan with your neighbours before applying for a planning permission and communicate about the concerns they might have.

How To Plasterboard A Wall

If you’re looking to plasterboard your wall, one of the essential things to have in mind is that the plasterboard must be hung horizontally and not vertically. Due to the way they’re manufactured, plasterboard sheets normally possess a “grain along the length. This implies that, it’s only when they’re firmly placed perpendicular against the wall that they’re able to achieve their maximum strength. Materials you’ll need to complete this task includes: Tape measure, stanley knife, pencil, spirit level, drill driver or screw gun, surform, drywall screws and handsaw. Now let’s have a look at the wall plasterboarding steps!

• To plasterboard a wall the first step to take is to place each board in such a way to make the edges the centre of the noggins and upright. Also, the the adjoining walls and door openings should fit closely to the edges.

• Work from the door opening to the ending wall. From the the stud’s edge to the noggin’s centre, use your tape measure to measure a cut board and as a rule to mark up.

• Place your spirit level on the marks and use the Stanley knife to run a line along the intended cut. Once done, turn the board on its edge and give a sharp push on the back to split.

• Cut the paper left with the knife after folding the split edge back on itself. This way, you should get a nice and clean edge.

• In its right position, place the board up against the studwork. Install the screws on the board’s edges where a noggin or upright can be seen.

• Mark lines down across the board at the stud’s centre.

• Cut the end boards to length.

• Install the remaining boards as mentioned above. While doing this, make sure the factory edges are together.

• Cut any board extending into an opening and finish the edges using a surform.

We’d recommend you hire the professional services of a plasterer for the best results especially if you lack the necessary training or experience. Plasterboarding a wall can be a tricky challenge and you’d save yourself some time, money and effort by getting it right on the first trial.

If you’re planning to acquire Sharps fitted wardrobes, one of the first few things that comes to mind is the cost to make such an acquisition. Generally, prices of these items can vary significantly. However, you should note that the more affordable end of the spectrum is most likely going to be around £750 to £900 per lineal metre, while mid range Sharps fitted wardrobes are usually within the range of £1400 to about £1600 per lineal metre. And finally, the high end customized Sharps fitted wardrobe are possibly going to be within the range of £3000 to £3500 per lineal metre.

The price of the Sharps fitted wardrobes is mainly determined by the fitted wardrobe solution your opt for. So let’s look at the estimated price range of Sharps fitted wardrobes depending on the styles you want for your home or property.

✓ There are the stylish, mordern sliding doors Sharps fitted wardron=be with mirrors that’ll make your room feel a lot bigger. If the type you opt for possesses three sections, then you’ll should expect to pay a price within the range of £2800 to about £3600 to have it fitted depending on the size of the room as well as the chosen finishes.

✓ Handcrafted, bespoke fitted bedroom wardrobe. This will cost about £2500 to £2900 with simple design details but the price can increase with ornate features like mouldings etc.

✓ Large bedroom 3m 80ccm three sections six door. This normally features finishes on both the interior and exterior as well as hanging space for clothes. It’s usually around £4900 or more.

✓ Simple two section closet. The price of this fitted wardrobe is usually within the range of £3200 to about £3500, but it could also be more depending on the design details you wish to implement.

Patios do not require lots of maintenance. They will only need occasional cleaning to make sure that the material keeps its original appearance. It's always best to clean your patio with a pressure washer and occasionally tap each slab or brick just to check the sand underneath hasn't washed away.

A barn conversion can be a great investment for lots of reasons. When done well, barn conversions can be great at holding their value, meaning you could sell yours for a great price. They can also look fantastic, often with period features coupled with large areas of glazing. This can make them a great place to live, especially if you enjoy being in the countryside.

However, barn conversions do have their disadvantages. They may require extensive renovation work to bring their energy efficiency levels up to standard, which can be very expensive. It’s also important to be aware of their location – they might be on a working farm or close to several other converted buildings.

It’s essential to get a survey conducted before you buy a barn you plan to convert. This can tell you about any structural problems it might have and give you an indication of whether you might be able to get permission to convert it. You can also buy barns with planning permission already in place.

In a nutshell, a mortgage loan is for the acquisition of an asset, so lenders won’t tend to give you anything else in a mortgage that is going to cover your home renovation costs. When you are applying for your mortgage, your provider will examine the price of your new household. For example, if you’re planning to buy a property for £200,000, but you need another £50,000 to help improve it, you’ll find that your lender might turn you down.

Essentially, with any mortgage loans that you take out on your possessions, the bank or creditor theoretically owns your home till you’ve entirely paid off your loan, which is why it is very unlikely that you will get extra funds from them. There are some mortgage providers who will be willing to add on some building costs, but it is entirely up to you whether to choose it or not.

With most mortgages, banks and other lenders will usually give you a maximum of 95% of what you purchased your property for. That means, that even if you contemplate the household has the probability to be valued at so much more, you’ll have to find an alternative way of paying for the developments you have in attention. So, if the accumulation of extra funds on to your mortgage loan is out of the question, you’ll need to find additional ways of paying for the home developments.

It is well and good if you have the cash saved up, or else, you can explore other payment options which your bank or lender may be able to help you with. There are several methods by which you can collect the cost to pay for the improvements, from personal loans to credit cards or even overdrafts, there are tons of ways to lending money. Keep in mind these are all forms of debt so keep an eye out for the interest rates when you are repaying.