Find a Builder you can trust in Menstrie.

Sand is a very important element in bricklaying as far as a mortar mix is concerned. Generally, the quality of the sand is the major factor determining the quality of a plaster mix or mortar mix. It’s recommended that the sand should have enough ‘fines’ (- 75 micron material) to get a good plastic mix with a water content that’s less than 350 litres/m3. Generally, a mortar mix or plaster mix is made within the range of one bag of cement to 200 to 300 litres of damp sand.

Apart from experience the next best indicator of the quality of sand is a field test. In other words, if you do not have the required training or experience in bricklaying, the best bet to determine the amount of sand for a good quality mix is by carrying out a field test. Let’s have a look!

• Get about 50kg of sand and air dry it.

• Scoop 25kg of the sand, 5 kg of cement as well as litres of water ( with 1 litre and 1.5 litres of the water in different containers).

• Mix the cement and sand to form a smooth, uniform and consistent colour.

• One after the other, mix the the sand - cement mixture in the three quantities of water. Do this until you’re able to achieve a mix that’s workable enough to use as plaster.

With that done, you should take note that if 5 litres of water is sufficient then the quality and quantity of the sand is perfect. If you’d require 6 litres of water to get a mix workable as a plaster, then both the quality and quantity of the sand is average. However, if you’d need 7 litres of water to get a mix workable as a plaster, then the quality of the sand is poor. Any requirement of water above 7 litres implies a very poor quality of sand.

There are so many benefits that comes with building a porch in your home premises. It’s an extra space where a lot can be achieved such as drying a dripping wet dog, taking off your dirty shoes or boot and lots more. So if you’re considering to construct a porch, it’s definitely going to be a wise decision. However, before you get started, there’s a need to determine if you’ll need planning permission for a porch. It’s important to take note that planning laws are dynamic and can be updated at any point, so be sure only to use trusted sources only as your guide. If you’re the homeowner or landlord, it’s entirely your responsibility to obtain the right approval for any development project you wish to carry out within your premises.

A Porch can not be termed as an extension and neither is it a conservatory, they’re basically built to the home’s front covering the main entrance using a stone base or a brick. As a result, a porch does not need planning permission due to the fact that it’s covered by the permitted development rights if the specific guidelines for porches are complied with. Below are the instances where you WILL need planning permission for a porch.

✓ If the floor space is more than 3sqm (the wall inclusive).

✓ The highest point has a height of more than 3 metres.

✓ If the porch is situated within 2 metres of a boundary directly facing on to the road.

You may need planning permission if the house is a listed building, designated area or falls under an Article 4 Direction.

In order to build a porch without planning permission, you need to consider all the criteria stated above. You can also visit the Planning Portal website to get more detailed information before getting started.

Garage conversion is a great way to add extra usable space to your home without having to extend your property. A fun fact is that, in the UK if you have your car parked in the garage, you’re in the minority. According to a research carried out by Admiral Loans, just about 33 percent of home owners in the UK store their cars in the garage. For most people the garage is literally a dumping ground that’s never fully utilized as such. In recent times, the garage is now being used to store a variety of other stuffs asides a car which includes garden furniture, tools and appliances, utilities such as washing machine, fridge and freezer as well as food and groceries. These facts show that more and more people are underutilizing their garage when they may actually be in need of more usable space in their property. So why not put into consideration converting the garage into a new space that would be able to serve more purpose?

If you’ve decided to convert your garage, you’d probably want to know the how long the project will take. There are a wide range of factors that can determine the duration of a garage conversion project. These factors include:

• If the foundation needs reinforcing

• If the floors, walls, or roofs are in a bad condition.

• If the ceiling height needs some raising

• If the insulation required in newer builds.

All aforementioned factors will make the garage conversion project take longer than expected. However, in normal situations garage conversions are relatively quick to complete once you start the building works. A single-car conversion will usually take about 3 to 4 weeks to complete depending on the existing garage’s structure.

How To Lay Loft Boards

Do you need more storage space in your home or property? If you live in a tiny space especially where extensions can’t be made sideways, why not look to the topmost area of your home and consider boarding out your loft to make it usable?

Boarding your loft can make for a fairly easy DIY project but like every other home improvement tasks, it requires some specific skill sets as well as knowledge for a successful construction. Therefore, we’d recommend you hire the services of a reliable professional in order to guarantee the best possible outcome, especially if you lack proper training or experience that’ll help you avoid some costly mistakes. Here, we’ll give you a good insight into the loft board laying procedures.

• Get The Right Tools & Equipment

The materials and supplies you’ll need to lay loft boards include loft boards, screws, tape measure and pencil, drill, hammer, saw, protective gear such as gloves and dust mask.

• Work Out The Area

Measure up the area you need the boards to cover. The standard loft features two different sizes (both are 18mm thick) which include 2400mm x 600mm and 1220mm x 320mm. You should ensure that the board you opt for fits through the loft hatch perfectly.

• Start Laying

Once you’re done working out the area, the next step is to put on your protective gear and start putting the boards in place. You should lay the boards in a staggered pattern so as to give a better strength. While doing this, watch out for any wire running through your loft so they don’t get trapped, you should also cut the boards for easy access to the light fittings’ top.

• Make It Permanent

Upon the successful placement of the boards in a way that offer a safe area to store things and stand on, you’ll have to screw them in place. Start by drilling 2 or 5 holes along the edge of individual boards in such a way that lines up with the centre of the joist below. Once done, then you can fix them in place with screws.

If you want to install an external wall, it is only wise to consider whether or not a planning permission is required in order to avoid a hefty fine. In a great kudos to the government and a welcome relief to home and property owners, the installation of external wall insulation is seen as an “improvement to the house and not an “extension or an “enlargement. Ultimately, this implies that external wall insulation fitting is to be done under permitted development and a planning application may not be required. However, like many other regulations, there are also exceptions to this rule and the main one is if the activity changes the appearance of your property. Properties such as a listed building having tighter regulations may pose some issues. As a result, we’d advise you to consult your local authority to ensure that there’s no fast rule to this topic before commencement of the external wall insulation project.

At the moment, according to the Government Building Regulations, the surface of the entire wall is to be improved to existing standards if the area to be insulated exceeds 25 percent of the wall. In normal situations this is usually the typical case, however to prevent avoidable fines and other possible punishments, it is always best to reach to your local authority and check out the rules guiding external wall insulation in your constituency. Furthermore, since external wall insulation is not a task that’s recommended to be done by yourself, you can also ask the professional external wall insulation fitting company for the applying rules before proceeding. As a good professional, the company should have a better knowledge of the rules and regulation guiding its activities.

The best type of insulation for your property will depend on the type of walls and any insulation that’s already present. It’s usually a good idea to have some form of wall insulation as well as loft insulation, as this helps to prevent heat loss in both areas.

It’s often said that a garage conversion can take anywhere between 1 week to 1 month, depending on the size and scope. But many standard conversions without any plumbing can take as little as 5 days. Your contractor will be able to tell you exactly how long your garage conversion will take.

Any residential building work requires a general builder. The term Residential building work means any work which is involved in building a house or changing or adding to a home. It also comprises of mending, refurbishing, ornamenting or applying shielding treatment to home. A dwelling is defined as a building or a part where people live. This might include an apartment, house or a townhouse.

Here is a list of some of the works that require a building licence:

• construction of a garage, carport or a shed

• renovation for bathroom, kitchen or laundry

• structural landscaping and building swimming pools

• construction of conservatories and atriums

• house lifting for example, raising the height of an existing structure permanently

• removing and resitting dwellings

• steam rooms and saunas.

General building contracts might also involve work that needs a specialist. These works can be appropriately subcontracted. However, this work must be carried out by the container of a permitted contractor licence or competent administrator certificate in that specialist category.

There are a number of different categories of licences that are available depending on whether you want to oversee the work or have an agreement with another party. When you have a contractor licence, you will have the option of submitting a contact to bid on the work. You can only do the categories of work designated on your licence card. Contractor licences can be allotted to people and businesses and partnerships.

With a certificate of a qualified supervisor, you will be able to supervise the type of work specified in the certificate. Such certificates are only issued to individuals and do not allow you to contract for work.

The licence of an endorsed contractor is issued to those individuals who have applied for a contractor licence but also possess the necessary qualifications and experience to become a qualified supervisor.