Find a Builder you can trust in Par.

If you’re considering converting a barn or buying one, you shouldn’t need to worry about it being cold. This is because building regulations dictate that when you convert a barn, you need to insulate it to meet specific standards. However, it’s worth considering its heating system and ceiling heights carefully – some barn conversions are likely to take longer and be more expensive to heat up than others.

Do I Need Planning Permission For A Loft Room?

The answer to this question is maybe. Generally, loft rooms are covered under “Permitted Development which means you won’t need to apply for a planning permission to build a loft room. This is like an advance planning permission provided by local authorities to allow some particular building works to be done such as loft conversions, rear extensions and more. When you’re covered by a “Permitted Development, you’re given the free range to oversee your home’s development without much interference from the regulations or the council. However, for permitted development to apply, there are some specific criteria that must be met. Therefore, if your loft room does not meet the following requirements given below, then you must complete a planning application before proceeding.

• In a terraced house, the converted loft space must not be more than 40 cubic metres.

• In a detached building or semi detached house, the converted loft space must not be more than 50 cubic metres.

• The existing roof slope at the front of the house must cover the extension made.

• The extension should not increase the height of the roof in any way.

• Verandas, balconies and any other structures of this nature must not be included in the extension’s plan.

• The side facing window openings should be at a minimum of 1.7 metres above the ground. The windows must be obscured as well.

• The roof extension should be set back as far as practically possible. It should be at a minimum of 20cm from the current eaves.

• The roof extension should not overhang the house’s roof or it’s wall.

• The materials to be incorporated must be the same or at least similar to what you already have on the house’s exterior.

When Does A Loft Become A Habitable Room?

When a loft is being converted to functional space, there are a multiple options it can offer. It’s not uncommon that at the conversion of this space, many household may not have a specific plan on how it’s going to be used. However, they know later on an actual need might arise, perhaps as you start working from home, developing other hobbies that requires an extra space or the family grows.

The loft can easily be converted into a game room, study room, playroom or even a household’s “breathing space etc. However, when the family grows and you wish to make use of the space on the top of your home as an extra bedroom, there are many factors to consider. The fact is, just because there’s enough space to fit a bed, doesn’t make it habitable. For a loft to become habitable, it must be built specifically for the purpose of being a sleeping area and must also comply with the relevant building regulations. It’s as a result of this, many property sale particulars include “potential third bedroom, subject to regulations statement written on it as well as the boarded and insulated loft space’s dimensions.

Loft conversions building regulations are set in such a way to ensure that adequate attention is given to both safety and structural elements to build a new space that’s fit for undetermined household use. These regulations are established minimum requirements to guarantee the following:

• The new floor and ceiling’s structural integrity.

• The existing roof and party wall modification’s structural stability.

• Safety during fire incidents plus an escape route.

• An appropriate stairway access.

• The proposed changes’ structural suitability to the external environment in association with the local area as well as any unique factors specific to the property.

Are you about to start a new construction job when it’s a heavily rainy period? Or perhaps you’re just interested in knowing how bricklayers work. Well regardless of your purpose, one thing you should know is laying of bricks has a few rules and one of them is not to lay a brick wall when its raining. This is mainly because your structure’s quality and integrity would be heavily compromised if water comes in contact with the mortar before it gets the time to dry. However, with the help of a concrete protective tent, you can prevent water from coming in contact and damaging the mortar. So let’s look at the procedures to follow to work in the rain!

lDetermine The Concrete Protective Tents Required

• Concrete protective tents come in various sizes so you have to know what’s required to get the job done.

• Firstly, calculate the amount of space required to lay the brick wall

• Then, incorporate the appropriate size and number of tents.

lSet Up The Tents

• Follow the manufacturer’s instruction to set up the tents

• Once installed, the tent should extend past the location for the bricklaying and slope downwards.

l Access The Area

• Inspect the location during rainfall to ensure water is not sneaking through.

lBuild a Lumber Frame

• Use 2 to 4 pieces of lumber to build a frame.

• Set it into the ground depending on the size of your wall

lApply Concrete or Mortar

• Fill up the frame with either concrete or mortar.

• Follow the manufacturer’s instruction to allow the mixture to cure.

lPrepare the Brick Wall’s Mortar

• Mix the mortar for the brick wall construction

• Follow the manufacturer’s instruction for the process.

When you’re done laying the bricks, you can remove the protective tents once you’re certain the rain has stopped. Exposure to sun and air will speed up the curing process, which is quite important to protect the integrity of your structure.

The short and simple answer to this question is yes, loft insulation does cause condensation. Over the years, problems with condensation in loft spaces have become increasingly common. While this may not be harmful in anyway, when the condensation becomes excessive it can lead to more serious issues taking root in your loft like wet rot, dry rot as well as black spot mould. Generally, the best thing to do if you’re concerned about the condensation in your loft space and that it may rapidly become a bigger problem is to get in touch with a damp specialist as soon as possible.

Even though insulating your loft space comes with a wide array of benefits like making the top floor rooms warmer, it’s however comes at the cost of making your loft or room space cooler. Condensation in lofts take place primarily due to the humid air making its way through insulation or other gaps into the loft space and touching a cooler surface which in turn results in beads of moisture on the timbers, lintels as well as the underside of the roof. This is why its always a great idea make use of thermal insulation with a vapour barrier that’s installed on the warmer side of the insulating material.

Condensation in loft is caused by excess moisture in the air and lack of adequate air ventilation. Here are some top reasons that gives rise to this in the loft:

• Extra insulation has been installed in the loft leading to a restriction on the natural air circulation in the property.
• When the storage boxes or other items that has been stockpiled in the loft blocks the roof vents.
• The release of steam and moist air into the loft space by hot water tanks.

Did you try rendering a wall but it doesn’t turn out the way you would have hoped for? Or perhaps you’ve been watching your wall render gradually deteriorate over time. Regard of your purpose, learning how to repair render cracks on wall is usually a great skill to have with your home maintenance in mind. However, whenever these crack are too large or difficult, we’d recommend you call in a reliable professional who can guarantee the best results for help. In this guide, we’re going to take you through the wall render repairing process. Let’s have a look!

No matter how solid a building material is, over time it’ll yield to the elements. When it comes to wall rendering it may be a case of too much sunshine or a costly mistake in the application process, but in truth, it cracks just because it cracks.

In order to repair render cracks, you’d have to start with a removal of damaged or cracked render. You’ll have to remove all the render or just a small section depending on the area you’re working on. If you’re able to clean all of the existing render as well as the paint over it all (both old and new), then removing a small section would work better as it makes it look neat and redone. Upon the removal of the existing render, the next important step would be to remove all loose material as well. Once done, you can then leave for up to 2 days to allow any trapped moisture to come out. Unfortunately, if the rains you’d have to wait till that dries too before you proceed.

Once dried, you can buy a pre-prepared render mix which already contains cement, lime and sand. Mix a 20kg bag with 4 litres of water (or check the product instructions and follow strictly), the mix to a fine consistency. Render is quick to dry, so you’d want to apply within 30 minutes of mixing. Make use of a trowel to apply the render on the affected spots and blend with the surrounding area.

One of the main reasons why fitted wardrobes are a popular choice amongst homeowners is due to the fact that they’re able to help maximise storage space and since they’re usually customized for the particular room, they’re always good looking. However, just like any other home item, over time your installed wardrobe may start to look a bit dated and old fashioned. In these type of events and in order to save money, several homeowners would prefer to update its look to a more modern one without having to completely replace the fitted wardrobe with a new one. In this guide, we’ll give some great tips on how to update your old fitted wardrobe. Let’s take a look!

✓ Add mirrors to the wardrobe doors. Your old fitted wardrobe may be made of old fashioned laminate or chipboard which happens to draw scratches and dents here and there. If this is the case, you can simply add mirrors to help conceal the damage or unsightly marks.

✓ Include decorative trimming or panelling. You can choose from the various styles of trimmings you’ll find at hardware stores. By adding some strips of moulding, the whole look of your fitted wardrobe can change significantly.

✓ Painting. If the surface of the wardrobe permits, painting can go a long way to alter the look of the wardrobe.

✓ Change the handles. Handles may seem as a little item that doesn’t add to the aesthetics of the wardrobe. However, in reality, change your old handle with a more modern and fashionable one can make a great difference to the wardrobe’s overall appearance.

✓ Upgrade the interior. You can upgrade the interior of your wardrobe to give you more options and a better appearance. For instance, you may wish to have part of the wardrobe to offer integrated shelving or perhaps pull out drawers rather than having all the interior space for hanging clothes and garments.

Pitting, also referred to as spalling is the event whereby “pits” or small holes start showing on the surface of your concrete driveway which makes it appear both worn and uneven. Concrete driveway pitting is a common but highly frustrating problem for most homeowners. You’ll see some concrete driveways that’ll only start to pit after a couple of years, but this is not true for all concrete driveways as others will start to show signs only after a couple of months. So how do you tackle this issue? Well, it’s relatively simple to tackle, however if you’re not confident or lack the necessary skills, we’d recommend you get in touch with a reliable professional who can guarantee the best results for help. In this guide, we’ll take you through the concrete driveway pitting repair process.

✓ Prepare the pits by cleaning the area, clearing out all debris and more. The small pits can be cleaned with a stiff brush while a sturdy broom will do a good job for larger pits.

✓ Make use of a hose to spray the concrete pits and flush out all remaining bits of waste.

✓ If you’re tackling series of small pits, simply use a caulking gun filled with pre-mixed epoxy and specially formulated for concrete to fill the pits. Clear off the excess eproxy ensuring that its level with the concrete surface. Once done, simply leave for at least 24 hours before the application of a concrete sealant to prevent the wear and tear of the new concrete.

✓ Chisel out a little concrete and clean with a pressure washer. Once done, apply a concrete resurfacing compound mixture into the holes and use a trowel to level off.

✓ Ensure that the repaired concrete driveway is protected from rain and foot traffic for at least 6 hours (or 24 hours for vehicles).