Find a Builder you can trust in Londonderry.

Do you know about 25 percent of heat that escapes from an uninsulated house are lost through the roof? Fortunately, roof insulation is something that can done by all DIYers irrespective of their experience levels. However, if you happen to lack the confidence necessary to pull off this, then it’s strongly recommended that you hire the services of a professional who can guarantee the best results and also save you time and money that could arise from potential cost mistakes. Let’s take a look!

• Clear out all clutter. This involves taking out all the rubbish and clutter from the loft. In order to work effectively, you’ll need a totally clear and empty loft space.
• Ensure that there’s sufficient insulation. The importance of a good ventilation cannot be overstated. Poor ventilation will result in forming of condensation and this condensation can make the roof timbers rot and compromise the structural integrity of the entire roof. If there are no roof windows which is the easiest way to provide a loft ventilation, the next best option would be to follow the loft floor along to the point where the roof comes down to meet it. There should be a gap at this point, also referred to as the eaves, between the outside wall and the underside of the roof.
• Measure your loft area. Take a measurement of the loft space in order to calculate the amount of insulation as well as the type you need. If you’re not sure, always get more that it’s required as skimming on the amount you use will only back fire in form of increased energy costs
• Check for water pipes.

To get started, simply make sure all cracks and gaps in the ceiling are filled using a standard filler or decorator caulk. Once done, clean the gaps in the joists and even to the point of hovering all the dust up. Finally,check for the hazards that can cause you problems before laying the loft insulation.

How To Dot And Dab A Plasterboard

If you want a fast and simple way to achieve a smooth and sturdy wall which is decoration-ready, then dot and dab plasterboard is the way to go! It’s a relative simple process but can also be a bit challenging. Therefore, if you lack the necessary training or experience, hiring a professional would be a great step to protect your investment and guarantee the best results. Here, we’ll provide you with a deep insight into the plasterboard’s dot and dab procedures. Let’s have a look!

• At the thickness of the board with the adhesive, mark the ceiling and floor as well as the wall to indicate the centre of each board.

• Ensure the wall’s height is 15mm more than the plasterboard

• Make a mixture of the adhesive and achieve a thick consistency. Apply a consistent layer of the mixture around the wall’s perimeter, edge of the ceiling and any other openings with the use of a trowel.

• Select dabs that are about 250mm long and 50mm to 75mm wide and apply the adhesive in them. Make use of 3 vertical rows for individual boards. Also ensure to apply, at skirting level, a band of adhesive.

• Position the board’s reverse side against the dabs, and laying against the packers. Then make the board align with the ceiling and floor marks with the help of a straight edge.

• Raise the board till its tight against the ceiling with a board lifter. Once done, use the plasterboard to wedge the board into place before you remove the board lifter.

• Repeat the same process for the remaining parts of the room. Once completed, make sure the adhesive is set before you remove the boards.

Yes. Most extensions will add substantial value to your home, and you may find that the extension adds more value than it cost. However, it’s important to be sure that the home remains balanced. Extending your garage and leaving your property with no parking spaces, for example, may impact your ability to sell.

So you’ve identified the type of garden room you’d like to construct in your property, chances are, you’ve already worked out where to put it and can’t wait wait to start spending valuable time on it. It’s very understandable to be a little impatient with the whole idea considering the numerous benefits provided by a garden, but just before you proceed with your plans there’s the need to first check whether or not you’re going to need a planning permission.

Factors determining whether you’ll need a planning permission includes where you intend to place it, the size of the room, how it’s going to be used as well as your location.

Generally, most garden rooms do not require a planning permission as they are categorized as outbuildings. In other words, you’re permitted to construct one so far you comply with some specific rules and have permitted development rights at your home or in your area.

If you want to build your garden room under permitted development, you have to comply with the following rules:

✓ The garden room shouldn’t be in front of your home or property.

✓ The total area of your extensions, sheds and outbuildings ( which includes your garden room), must not go beyond 50 percent of the total land area surrounding your property.

✓ It must be a single storey that’s less than 3 metres high ( 4 metres for a dual pitched roof). And it must not go beyond 2.5 metres in height if the structure is within 2 metres of your boundary.

✓ The eaves must not go beyond 2.5 metres above ground level.

✓ It must not feature a balcony, veranda or any raised platform

✓ It must not be a self contained living accommodation.

You should note that if your home is a listed building or you happen to live in a designated area, then you might not have permitted development rights.

How long it takes to install insulation will depend on the size of your property. In general, loft and cavity wall insulation can be installed in a day or two. External wall insulation will usually take longer to install. The rep or installer will be able to advise you when quoting for the job how long this will be.

Are you looking to pebble dash your house? This is a cool way to add a stunning new look to your home or property while also adding to its resale value should you wish to sell later on. The list of the benefits goes on, however one thing that most home and property owners would like to know before starting such a project is exactly how long it’ll take to complete it. If you’re also having similar thoughts, then you’ve come to the right place! In this post we’re going to give you an insight into the duration of pebble dashing a house. Let’s take a look!

First and foremost, just like any other home improvement project, the duration of a house pebble dashing project is affected by a number of variables. These variables include the size of your house, the company or contractor hired and lots more. In general, a house pebble dashing project should take within the range of 3 to 14 days depending on the size of your home. It should be noted that you’ll have to pay the workers on a daily basis. Most labourers will charge within the range of £140 to about £160 per labourer per day. And you should expect to have at least 2 labourers to work on your house’s pebble dashing project per day. On the other hand, the more labourer you have working on your project, the more you’re going to pay on a daily basis but this will also significantly reduce the time frame it’ll take to get the project over the line.

Windows or lightwells can be a great way to introduce natural light into your basement, making it a more valuable, enjoyable space. However, they’re not always an essential requirement.

It’s important for your basement conversion to meet ventilation and fire safety building regulations. Windows can be a good way to do this, but they’re not the only option. Stack or mechanical ventilation, or ensuring that stairs up from your basement connect to an exit can be a good alternative.

So, while windows can be a great asset to your basement conversion, if you can’t afford them or they’re not structurally feasible, you can still create a basement conversion without them.

With cavity walls being very similar to other type of brick works, it can be quite confusing to figure out the type of wall your property possesses. If your house was constructed after the 1920s, then its highly likely the you have cavity walls, while older houses (houses before the 1920s) are likely to have solid walls. What’s more? If you happen to own a home that was built in the last decade, then it’s very possible that it was built with insulation installed during construction.

An effective way to determine whether or not your property is built with cavity wall is to examine the brickwork on your home’s exterior. The bricks will typically possess a regular pattern if it features cavity walls. In the event whereby the brick work is covered by render, you can also figure it out by taking a measurement of the wall’s width. If the brick wall is beyond 3000mm in thickness ( from the exterior wall to the interior wall), then it probably features a cavity. Meanwhile, a wall that’s narrower is very likely to be solid. Stone walls, on the other hand, may actually be thicker but are most times solid.

In a situation whereby your house is built using steel frame or timber frame, or made using pre-fabricated concrete, there are varying rules that applies when it comes to insulation and should be examined by an expert before any insulation is installed. More often than not, most contractors will have installed special air vents, which can also be a good indicator that a cavity wall insulation has been done.