Find a Builder you can trust in Abbotsbury.

How To Fit Plasterboard

If you’re planning to renovate your house, then here is a must-read guide! Fitting of plasterboard is a crucial step when it comes to renovation. If you’re bringing down an existing lath and plaster for an upgraded surface or adding a new wall, a plasterboard is required for your project to be a true success. If you’re a novice with no prior practice or experience, you can protect your investment by hiring the services of a professional plasterer to guarantee the best results, the first time. However, we’ve put together this guide to give you an insight on how the plasterboard fitting process is done.

To get started, you’ll need a power drill, hammer, plasterboard nails or screws, broad knife, utility knife, measurement tape, pencil, ladder as well as a joint tape.

Before proceeding, you need to identify the number of plasterboard sheets needed to commence the project by measuring the height and width of the wall as well as calculating the square footage. If you possess a stud timber wall, the steps below will get you the best results.

• Measure the walls and mark the plasterboard where you’ll make the cuts. Start with a full sheet and cut pieces down in such a way that would fit

• Score the front paper of the plasterboard with utility knife. Fold the sheet to get a clean cut through the board and make use of the knife to the remaining paper.

• Place the first sheet against the wall and use an offcut to prevent the plasterboard from touch the floor.

• Make the plasterboard rest snugly against the wall in position and screw it firmly on each stud. Once done, fasten it at all the sheets’ edges and in a line down the stud to make for a firm connection. Follow the same process for the remaining plasterboard sheet till the wall is fully covered.

Cutting a plasterboard is a relatively simple process requiring only some basic tools. Unfortunately, the lack of knowledge serves as big deterrent for many people who wishes to put it to good use. Plasterboard can actually be sawn using an ordinary timber saw that’s fine-toothed to get a cleaner edge. However, the basic tools you may also need includes a sharp knife (Stanley Knife), pencil, a fine sandpaper, a straight edge and measurement tape as well as a wall board saw. Let’s have a look at the cutting process!

• Firstly, you need to put the plasterboard sheet flat on a firm surface.

• Use the tape measurement to measure the cut you wish to make.

• With the help of a pencil, simply mark out the part you wish to cut on the plasterboard’s front side.

• Once marked, place a spirited level over the marked spot on the plasterboard sheet you want to cut.

• Cut a shallow mark into the plasterboard sheet using the Stanley Knife to cut along the edge.

• The cut should be slow and gradual to ensure you do not wander off the edge of the marked area.

• Once the shallow cut has been made, turn the plasterboard sheet on its edge and deliver a quick and sharp push towards the plasterboard’s back and on one side of the cut.

• Place the plasterboard sheet backing against a flat surface ensuring the line of the cut is over an edge. Once done, give a quick and sharp push towards the back of the plasterboard sheet and on the part of the board is reaches beyond the edge.

• Using a fine sandpaper, remove all forms of paper burrs.

The process of cutting plasterboard requires a lot of practice. If you lack the training and experience, the cutting process is best left to a proficient professional who can guarantee the best results the first time and save you some additional costs due to potential damages.

Render serves two basic functions. One is it’s protective qualities as render acts as waterproof for the wall which enables them breathe by allowing water vapour move from the inside to the outside of the structure while also working to prevent water or rain from finding its way inside the structure. While the second function is the decorative qualities as render is able to provide the structure with a fine finish and colour to make the building a lot more appealing and correcting faults in line and level in the masonry.

If you wish to apply render on your external wall, you’d probably be wondering just how thick the render should be to perfectly serve both of functions. In this article, we’re going to take a look at just that!

For a render thickness, the British Standard Wind Driven Rain Index has come up with 4 ratings which include Sheltered, Moderate, Severe as well as Very Severe. An area with Very Severe rating include South West England. This rating implies that the thickness of the render in this area should be increased to at least 20mm for a direct one coat render applications as well as 5 to 6 external wall insulation base coat applications. And if you happen to reside within one mile of the coast, it’s strongly recommended you incorporate an extra repellent protection like Paraguard AG from Parex.

In general, render that’s prepared on site with cement and sand should be have a minimum of 20mm to 25mm thickness. Although, it should be noted that the quality of the render is based on quality of the sand incorporated, the design mix as well as being largely dependent on how good the mixing technique from the applicator is. The most common reasons why traditional renders fails is due to both poor mixing ratios and low quality materials used.

Builders are everywhere, but finding one for your project can be tricky and stressful, with both cost and reliability coming into question. This is even more worrisome when you’re fully aware that your house extension can only be as good as the builder. If you’re also facing the same challenge, then you’ve come to the right place. In this article, we’ll share with you some tips on how to choose a professional and reliable builder who’ll ensure you get immense value for every penny spent. Let’s take a look!

✓ Ask for recommendations. To find a tradesperson, not just a builder, personal recommendations is the best way to go. Building a house extension is a major undertaking which comes with a lot of costs, so if you’re going to do it the least you can do is ensure you do it right. Carry out your research, ask friends and family, neighbours and loved ones if the know of any reliable builder in the local area. If they’ve have one they’ve used, you can request for the cost, quality of the job done, the duration of the project and any other detail you feel you should know.

✓ Search Online. Use our search feature to look at the builders available or submit and enquiry and we will find you one. Our site holds details of numerous builders and building companies which you can go through their ratings to select the best.

✓ Select a reliable builder from trading association. Most reliable builders are usually a member of a recognized trading association or the other. Though this is not obligatory for builders, but it can be used as a dependable medium to find a good builder. We list what trade association the builders are a member of.

Many types of loft are suitable for a loft conversion. In general, you will need at least 2.3 metres of headroom in your existing loft. This is to make sure there is enough headroom after the conversion. Speak to a conversion specialist about the probability and possibility of doing this in your house.

As with every home development project, a home makeover comes with heaps of preparation and, hard work, but it is a remarkable way to breathe new life into an old home.

RESEARCH PERIOD FEATURES AND SAFEGUARD THEM

Get to know your household better, the time it was constructed in, and the kind of individuals who would have lived there. The greatest tactic is to repair current structures, make the house dry and safe.

CHECK FOR RENOVATION RESTRICTIONS BEFORE YOU START

There are certain restrictions that don’t allow you to remodel your house after a certain extent, it should be made clear to you when you purchase the property but if you are unsure about the regulations you should check them up, as it is a criminal offence to carry out unauthorised work to a listed home. Restrictions in Conservation Areas generally affect only the exterior of the property as the intention is to ‘preserve or enhance the character or appearance’ of an area, but the right to develop your house will be affected. This means the kind of work that you could have easily completed in a different location may need certain planning and even permissions to complete in your area.

CREATE A DESIGN FOR YOUR HOUSE RENOVATION

It is very important that you take your time to perfect the design. This will help to ensure that the finished work is in tune with your needs. You will also need to figure it out how the changes might play with the original building.

FIND THE BEST CONTRACTORS FOR YOUR RENOVATION

If you are planning on managing the renovation project yourself, it is advisable to ask from friends or family who have renovated their house before and have undergone a similar experience. They can help you find the right architect and builder. Or else, you can always opt for a project manager.

How To Repair Sunken Concrete Driveway

If you have concrete driveway that’s cracked, uneven and mostly especially sunken, you’d know how distasteful it can be just viewing it on your property. A sunken concrete driveway is most likely caused by rainwater erosion removing the soil under it or a big root under it which as rotted over time. Another possible cause of the sunken concrete is an improperly prepared base which implies that the soil beneath wasn’t fully compact when the concrete was poured on it. Later on the soil beneath will eventually settle and shift below the concrete driveway which weakens the integrity of the entire driveway, making it more vulnerable to cracks, unevenness and sunken.

Two ways in which you can fix this problem includes either demolishing the whole driveway, re-compact the soil underneath and fill with new concrete or repair the entire driveway using an easy process called slabjacking. In this article, we’re going to look at the slabjacking repair process as it’s significantly less expensive than the demolishing approach and will also cause minimal disruption to your lifestyle.

Also referred to as mudjacking or concrete lifting, slabjacking is simply a process used to float your existing concrete back to its original position. If you are not a competent DIYer or lack confidence to pull this off, we’d recommend reach out to a professional for help. If otherwise, then you can practice the slabjacking process given below.

✓ Drill holes through the slab.

✓ Pump grout mixture through the holes. This mixture will spread out beneath he driveway and raise it up.

✓ Lastly, fill the holes and level the concrete driveway surface.in such a way to hide the signs of the repair made.

This is a process that works to efficiently get your driveway back in a top condition relatively quickly.

If you’re currently experiencing some structural issues with your building or property and you’ve heard a thing or two about the several benefits associated with getting underpinning done, you may be wondering if underpinning might just be the answer to your worries. Well, one thing you should when it comes to underpinning is the fact that, while there are some structural issues that may actually warrant an underpinning job, there are also some situations that can not be fixed by underpinning. In this post, we’re going to consider the events whereby underpinning of your house will be required. Let’s take a look!

First and foremost, you should know that underpinning isn’t required for issues related to slab heave. Footing movements which are likely to reverse normally occur when the content of the soil moisture changes unevenly which gives rise to slab heave. This movement results for a reversible effect.

Generally, underpinning is done to remedy problems related with the movement of the footings of a building or property, but as stated above – not all movements require underpinning. So, when is underpinning required? More often than not, a situation that’s resolved by underpinning is the event whereby the footings of a building or structure drops or subside as a result of some reasons that are irreversible. For example, footing movements caused by a footing set on a soft or loose soil which may be irreversible.

In the event whereby the footings of your house haven’t been installed as deep as required during the initial construction, then you will need to have your building underpinned to make it more stable. If you’re also looking to increase the load on your foundation like adding another storey, you may also need to have your house underpinned to support the extra weight added.