Find a Builder you can trust in Ferryside.

Rendering a house’s external walls is one of the cheapest and most effective ways by which a building can be made waterproof and also good looking. If you’re thinking about rendering your house, figuring out the cost of completion is usually one of the most important things you’ll have to consider before you proceed and if you don’t know where to start, finding an experienced tradesperson who possesses several years of experience as well as the ability to overcome the different issues that he may be faced with while on the project is paramount. If you’re able to get one, however, you should know that they rarely come cheap.

When trying to determine the accurate house rendering cost estimate , a tradesperson will put into consideration a great number of factors. Even at that, a rough estimate still requires both skills and expertise to be able to take into account all the necessary factors. In general, a typical 3 bedroom home in the UK will cost within the range of £4000 to about £5500 for a complete render job on the outside and covering from top to bottom.

Usually, the most important factor which play the biggest role when determining rendering costs is the area that’s going to be covered by the render mix. Professional contractors will provide a quote based on the rendering costs per square metre. Below are some rough estimates of rendering costs of properties depending on their size (without VAT).

✓ For a small mid terrace house of about 40 to 50 square metre, the total rendering cost estimate is £3000 to £4000.

✓ For a large mid terrace house of about 70 to 180 square metre, the total rendering cost estimate is £3000 to £5000.

✓ For a three bedroom detached house of about 100 to 160 square metre, the total rendering cost estimate is £4000 to £5500.

Are you considering a dormer loft conversion for your home? If yes, then you’d probably want to know how much it costs. Unfortunately, due to the several variables and influencing factors, a precise answer can not be provided for all dormer loft conversions. In this article we’ll give you a vague idea of the general cost so you can set a more realistic budget and start planning.

There are three main types of loft conversion which includes the Velux, Dormer, and Mansard. Out of the three types, the dormer happens to be the most common type and possesses a small flat roofed extension with a window. The dormer loft conversion will usually cost within the range of £25,000 to £30,000.

The price for a smaller dormer loft conversion, mid range dormer loft conversion and large scale dormer loft conversion will be at £2,000 to £7,000, £10,000 to £30,000 and £40,000 to £60,000 respectively. However, you should take note that the prices given are all based on varying influencing factors such as the type of installation that is selected, the type of the rood, en suite conversion as well as other customization. Changes in price can be as a result of the materials required and the extra time per labour that’s needed to complete this home improvement project by the tradesmen employed.

Furthermore, a dormer loft conversion average cost will also depend on the type of dormer you opt for. Here is a list of the most common applications:

✓ Blind dormer loft conversion - £3,200 to £4,400

✓ Recessed dormer - £1,300 to £1,850

✓ Barrel roof dormer - £3,000 to £4,600

✓ Gable dormer - £5,500 to £7,500

✓ Hipped roof dormer - £5,600 to £6,660

✓ Pedimented dormer - £12,700 to £23,100

✓ Flat roof dormer loft conversion - £13,800 to £21,600

No matter how big or small a building is, it can only be as good as it’s foundation - and that’s a fact! It all starts from the footing and when it isn’t deep enough, unlike badly installed gutters or gapped hardwood flooring, can make the whole building collapse to the ground. Just like any code recommendations, the depth of the footings of your porch is a parameter that must be complied with and adjusted to suit your local code requirements.

As a rule of thumb, you should always dig below the frost line when excavating your footings. At this depth level, the moisture present in the soil will be frozen. Ultimately, this will help the ground to act as a barrier to insulate the soil below the footing from freezing during the cold months. As a result, in regions where the weather is almost always very cold the depth of your footings is expected to be at least 48 inches. But in areas featuring a warm climate, you may be allowed to install your footings on grade.

In addition, it’s compulsory that your footings must be installed at a minimum depth of 12 inches below unsettled soil. However, if you’re constructing the structure into a steep hill’s side or by the side of a retaining wall, it’s required that you maintain the least distance to grade both vertically and laterally. In the event whereby you need to achieve a good lateral barrier, you’ll need to have your foundation dug a lot deeper compared to if it’s on a flat surface. For a more accurate and updated information, you can consult your local building inspection department to get familiar with the requirements in your area.

How To Plasterboard A Wall

If you’re looking to plasterboard your wall, one of the essential things to have in mind is that the plasterboard must be hung horizontally and not vertically. Due to the way they’re manufactured, plasterboard sheets normally possess a “grain along the length. This implies that, it’s only when they’re firmly placed perpendicular against the wall that they’re able to achieve their maximum strength. Materials you’ll need to complete this task includes: Tape measure, stanley knife, pencil, spirit level, drill driver or screw gun, surform, drywall screws and handsaw. Now let’s have a look at the wall plasterboarding steps!

• To plasterboard a wall the first step to take is to place each board in such a way to make the edges the centre of the noggins and upright. Also, the the adjoining walls and door openings should fit closely to the edges.

• Work from the door opening to the ending wall. From the the stud’s edge to the noggin’s centre, use your tape measure to measure a cut board and as a rule to mark up.

• Place your spirit level on the marks and use the Stanley knife to run a line along the intended cut. Once done, turn the board on its edge and give a sharp push on the back to split.

• Cut the paper left with the knife after folding the split edge back on itself. This way, you should get a nice and clean edge.

• In its right position, place the board up against the studwork. Install the screws on the board’s edges where a noggin or upright can be seen.

• Mark lines down across the board at the stud’s centre.

• Cut the end boards to length.

• Install the remaining boards as mentioned above. While doing this, make sure the factory edges are together.

• Cut any board extending into an opening and finish the edges using a surform.

We’d recommend you hire the professional services of a plasterer for the best results especially if you lack the necessary training or experience. Plasterboarding a wall can be a tricky challenge and you’d save yourself some time, money and effort by getting it right on the first trial.

If you’re planning to construct a kitchen extension on your property, one of the first things that comes to mind is whether or not you’ll require a planning permission before you proceed. Generally, kitchen extensions are normally classified as permitted development which allows you to carry out your project without any interruptions from the law or your local authority. In other words, if your extension is meets up with the guidelines of the permitted development rights, you won’t have to apply for a planning permission. However if otherwise, you’ll have to apply for a planning permission to your local council and may require additional reports. And regardless of your position, you’ll always need building regulations approval before you can carry out any kitchen extension project. It may also be required that you’ll have to issue a part wall notice if you’re to build on or close to the boundary with a neighbour.

If you don’t want to go through the hassle and stress involved in applying for a planning permission with your local council, then you must ensure the following:

✓ Your kitchen extension must not be over half of the area of land around your main house.

✓ The kitchen extension must not be side elevation onto a highway or forward of the principal elevation.

✓ The extension must not be taller than the highest part of the roof.

✓ The height of your kitchen extension must not go beyond four metres.

✓ Kitchen extension that’s more than one storey must not go exceed the rear wall of the main house by more than three metres.

✓ Two storey kitchen extensions must not be closer to rear boundary by anything less than seven metres.

✓ The kitchen extension must not include balconies, verandas or any raised platforms.

Due to the fact that we live in a country (the UK) with so much history as well as architectural beauty, there’s a need to have what’s commonly called “Conservation Area. A Conservation Area is basically an area which is designated by the local authority and is established in order to protect and enhance areas of historical and architectural interest which includes both rural and urban areas. Therefore, when it comes to refurbishment project in a conservation area, there’s usually a lot of things that needs to be put into consideration as well as hurdles to scale in order to make alterations to your property without any interruptions from the law.

In general, all properties in a conservation area have strict regulations governing the outlook of the houses, as this plays a major role in the appearance of the area as a whole. As a result, if you wish to bring down a building, fence, wall or even railing and the likes, you’ll need to obtain prior consent before you proceed. An easy way to go about any refurbishment plan is to to ensure the usage of exactly the same materials that exists in the current house. When you abide by the rules, you’ll be in a more favourable position to acquire the needed prior consent.

The short and simple answer to the question is yes, you can refurbish a house in a conservation area but subject to the approval of the local authority through a planning permission. And when it comes to submitting a planning application for approval, some are aspects will usually be subjected to more intense examinations than the others. Hence, the need to make sure that your refurbishment plans are all friendly in a similar way to the neighbouring buildings and environment.

Whether a basement is worth converting depends on your location and how much work it requires.

A basement conversion can be a great way to add space to your home, and can raise your property value. However, it can also be one of the most expensive ways to do this, so if there’s a possibility to extend your property, or convert a loft or garage, it’s worth considering this first.

You should also compare how much your basement conversion will cost with the amount it could raise your property value by. In some areas, a quality basement conversion could earn you money in the long run, but in others it’ll only cost you. If you’re planning on staying in your property for a long time this might not matter to you, but if it’s not your forever home then it’s an important thing to think about.

Cladding comes in a range of styles, such as flush, shiplap, and featheredge. Many types of cladding are also available in a variety of colours to suit any property. A cladding specialist will be able to discuss what solution is best for your property and how it works.