Find a Builder you can trust in Lymington.

With the title of this blog, do not be deceived into thinking the purpose is to encourage you to install an external insulation by yourself. Even as a competent DIYer, it’s not advisable to buy a couple of materials and start slapping it into the wall hoping for the best outcome. External insulation is by no means a DIY job and without the proper training and experience, it can easily turn out disastrous resulting in loss of time, effort and money in such a valuable project. This blog, however, will give you a great insight on how the installation process works and help maximize knowledge ensuring you do not spend more than necessary.

External Insulation Installation

lRender Test

• This is done to ensure the existing render is good enough for insulation support.

• If positive, the insulation can be applied directly onto it.

• If negative, ensure removal of the old render before fitting the insulation.

lPipework Adjustment & Removal

• Remove all pipework prior to insulation fitting

• Install temporary downpipes to ensure water is not wasted and everything continue to function normally during the insulation fitting process.

lWindow Protection

• Protect the window with a protective layer or film.

lStarter Track Fitting

• Determine level you want the insulation to start (height).

• Fit the aluminium start track or carrier tray at the identified level.

lInsulation Boards Fitting

• Apply a layer of adhesive to the board and glue them to the wall in a staggered pattern.

• Cut to fit round all obstructions and windows.

• File off the edge of the board where necessary using a rasp upon successful fitting of the boards

lMechanical Fixing Inclusion

• Hammer around 10 fixings per square metre into the board.

• This is to secure the insulation boards.

lBeading Fitting

• Add corner beads and stop beads to ensure the insulation is secure and to prevent it from making contact with other materials.

lReinforcing Mesh & Render Addition

• Apply two layers of strengthening properties and between the two layers of render, include a fibre glass mesh.

lPrimer Application

• Paint on the primer

lFinal Render Application

• Choose your most preferred texture and colour as this will be the last coating of the installation process.

lPipework Re-installation

• Re-install all detached pipework at the start of the installation process.

Do you want to beautify and increase the value of your home? If yes, a refurb and house extension is definitely a great option to consider. Depending on your home extension project, the value that’ll be added to your home’s resale value varies. However, the cost of completing a house extension project can be huge, so you just might want to consider your financing options. Fortunately, there are various options through which your house extension project can be funded with each having its own pros and cons. Your specific circumstances will determine the one that’s going to work best for you, so let’s take a look at some of the best options to help you fund your project.

• Home Remortgaging

The process whereby a mortgage is transferred from one provider to the other is known as remortgaging. This is usually done to generate funds for a project by entering a more lengthy repayment term commitment when switching. If you want to raise your funds in a quick manner, this process works best.

• Savings

This is a good reason to cultivate a good saving habits. If you’ve been able to save up some mega bucks then you’d probably won’t have to borrow money to finance your house extension.

• Unsecured Loans

If you do not buy into the idea of borrowing more against your property, you may just be able to apply for an unsecured loan especially if you have a good credit record. A secured loan makes use of collaterals like a car or house to serve as a cover for the lender, meanwhile an unsecured loan is based mainly on the credit managing history of the borrower.

• Credit Card

There are some great benefits that comes with financing your small or medium scale extension project with your credit card. Not only does it offer some real lifeline if problems arise during the project, but you can also avoid paying excessive interest on the investment by ensuring your deal has a 0% introductory rate.

If you’re considering converting a barn or buying one, you shouldn’t need to worry about it being cold. This is because building regulations dictate that when you convert a barn, you need to insulate it to meet specific standards. However, it’s worth considering its heating system and ceiling heights carefully – some barn conversions are likely to take longer and be more expensive to heat up than others.

This is a type of loft conversion that extends your roof on the sloping side. It is a great option to go for especially where a hipped roof effectively makes the usable floor area a lot smaller which can be a tricky affair when it comes to putting in a new staircase. Here, the roof is extended from the current ridge in such a way that it effectively fills the gap between them. As a result, this turns the hip (in a hipped roof) into a gable to create space in your roof for a loft conversion - hence the name “hip to gable.

The new gable can be done in whatever way that suits both your taste as well as your property. You can make the new gable construction in woods and then tiled to match your existing roof while you can also go for other options such as brick block pebbledash or rendering. You are also free to fit in a new window into the loft conversion end so as to allow for natural light into the loft space.

A hip to gable loft conversion is mostly found on both semi detached and end terrace buildings, particularly those constructed in the 1930s. Overall, this type of loft conversion is particularly ideal for homes that features a hipped roof and with a sloping roof at the side of the property. Some detached properties can also possess a hipped roof on the side - and as such, a double hip to gable loft conversion can also be deal as it’ll create more loft space for usage. If your home fits into the bill, then you should be aware that once the project is completed, you’ll have plenty of usable space available to both you and your loved ones.

How To Dot And Dab A Plasterboard

If you want a fast and simple way to achieve a smooth and sturdy wall which is decoration-ready, then dot and dab plasterboard is the way to go! It’s a relative simple process but can also be a bit challenging. Therefore, if you lack the necessary training or experience, hiring a professional would be a great step to protect your investment and guarantee the best results. Here, we’ll provide you with a deep insight into the plasterboard’s dot and dab procedures. Let’s have a look!

• At the thickness of the board with the adhesive, mark the ceiling and floor as well as the wall to indicate the centre of each board.

• Ensure the wall’s height is 15mm more than the plasterboard

• Make a mixture of the adhesive and achieve a thick consistency. Apply a consistent layer of the mixture around the wall’s perimeter, edge of the ceiling and any other openings with the use of a trowel.

• Select dabs that are about 250mm long and 50mm to 75mm wide and apply the adhesive in them. Make use of 3 vertical rows for individual boards. Also ensure to apply, at skirting level, a band of adhesive.

• Position the board’s reverse side against the dabs, and laying against the packers. Then make the board align with the ceiling and floor marks with the help of a straight edge.

• Raise the board till its tight against the ceiling with a board lifter. Once done, use the plasterboard to wedge the board into place before you remove the board lifter.

• Repeat the same process for the remaining parts of the room. Once completed, make sure the adhesive is set before you remove the boards.

How To Fit Plasterboard

If you’re planning to renovate your house, then here is a must-read guide! Fitting of plasterboard is a crucial step when it comes to renovation. If you’re bringing down an existing lath and plaster for an upgraded surface or adding a new wall, a plasterboard is required for your project to be a true success. If you’re a novice with no prior practice or experience, you can protect your investment by hiring the services of a professional plasterer to guarantee the best results, the first time. However, we’ve put together this guide to give you an insight on how the plasterboard fitting process is done.

To get started, you’ll need a power drill, hammer, plasterboard nails or screws, broad knife, utility knife, measurement tape, pencil, ladder as well as a joint tape.

Before proceeding, you need to identify the number of plasterboard sheets needed to commence the project by measuring the height and width of the wall as well as calculating the square footage. If you possess a stud timber wall, the steps below will get you the best results.

• Measure the walls and mark the plasterboard where you’ll make the cuts. Start with a full sheet and cut pieces down in such a way that would fit

• Score the front paper of the plasterboard with utility knife. Fold the sheet to get a clean cut through the board and make use of the knife to the remaining paper.

• Place the first sheet against the wall and use an offcut to prevent the plasterboard from touch the floor.

• Make the plasterboard rest snugly against the wall in position and screw it firmly on each stud. Once done, fasten it at all the sheets’ edges and in a line down the stud to make for a firm connection. Follow the same process for the remaining plasterboard sheet till the wall is fully covered.

How To Put Up Plasterboard

Putting up a plasterboard is a vital process when it comes to home renovations. However as daunting as it may seem, with a good guide and regular practice you can master the skill within a small period of time. If you lack proper training and experience, we’d recommend you hire a seasoned professional plasterer for help so as to get the best result and also avoid additional costs due to possible damages.

Putting up plasterboard is way quicker than wet plastering and also significantly reduces the drying time that can slow down your renovation plans. With a plasterboard, you can delve straight into the decorating stage and achieve a smooth finish. Below are the steps required to put up a plasterboard.

• The first step is cutting the plasterboard to shape which be one of the most challenging parts of the process. This is because you’ll need to fit the board around things such as plug sockets and window sills. As a result, this involves cutting complex shapes rather than just a simple straight line. To get this done, simply mark out the cut required with the use of a tape measure, combination square and spirit level for a better precision. Once done, you can then use a plasterboard pad saw to cut along the marked spots.

• After you made the required cuts, the next step is putting up the plasterboard. And depending on where the boards are going to be put, this could be a very challenging task. If you’re going to put the boards on the ceiling or somewhere very high up, you’d probably need an extra pair of hands for help. To get this done, use the appropriate screws to secure the boards in place if you’re installing them directly on studs. However, if you’d be fixing them onto bricks or blocks, a drywall adhesive is your best bet.

With the prices of buying a house skyrocketing, many of us are tempted to building our own house. This is sometimes an excellent choice, but you will first need to understand the costs of building a house from scratch. As per a general estimate, the cost of self-build ranges between £300 per m2 to £3,000 per m2.

As you can see, this is quite a variation in price from lowest to highest. Location is a prime factor in determining the costs. Building a house in London and the South is more expensive compared to other regions. Aside from location, several other factors make up the price.

Self-manage with subcontractors

You hire professionals directly like builders and carpenters. You also buy all the materials yourself allowing you to get the best prices.

Hiring a main contractor with other subcontractors

You will first need a main contractor who will help to create the watertight structure for your house. For the rest of the work, try hiring out subcontractors. Make sure that you buy all the materials yourself to get the best price.

External cladding materials

If you are looking to install other external material other than brick, you will also need to factor in the cost for the same.

Here are some example prices:

• Render on blockwork costs around £25 per m²

• Timber cladding is around £25 per m²

• Hand¬made all-weather tiling costs around £54 per m²

• Rubble walling or flint is around £90 per m²

• Reconstituted stone costs about £48 per m²

• Natural stone is about £75 per m²

Make sure to include these costs when coming up with the estimate.

Roofing materials

Non-standard roofing materials tend to add more to the cost and therefore you will also need to account in for this factor.

Here are some examples:

Welsh slate – £60 per m²

Second-hand slates – £35 per m²

Handmade clay tiles – £65 per m²

Reed thatch – £80/m²

If you choose to add any unique material to your roofing, be sure that you remember to factor in its cost.