Find a Builder you can trust in Arisaig.

Insulating a cavity wall should not affect the damp proofing of the wall. All insulation approved for use in cavity walls has been tested to ensure that it does not allow damp to pass through the wall. Some walls which receive a lot of wind driven rain are unsuitable for cavity wall insulation.

For 2 metre solid fences it’s recommended to use concrete posts to support each panel. For smaller 1 metre fences or for picket fences with gaps between each timber piece you can use timber posts. A fencing contractor will be able to advise you on the best materials from the length and requirements of a new fence.

With the ability to add approximately one third of your existing living space ( by converting your old, unused attic) to your home or property without having to let go of your garden, it’s quite easy to see the reason why loft conversion has rapidly grown to become one of the most popular home improvements in the UK. However some homeowners usually shy away from the idea simply by looking at the perceived high cost of carrying out such a project, despite several researches showing that loft conversions offers the best rate of return on initial investment when compared to the other home improvement projects. So exactly how much would it cost to carry out this project?

Just like several other home improvement projects, the cost of a loft conversion varies greatly depending on a wide range of influencing factors. These factors include the size of your home, how old your home is as well as the quality of the fixtures and fittings you want to install. For instance, a high end bathtub alone can cost you thousands of pounds, meanwhile you can also construct a full bathroom suite on just a couple of hundred pounds. However, to give you an idea of the minimum cost of a loft project we’ll look at the most popular types and the minimum cost of each.

✓ Internal Loft Conversion - The most affordable type of loft conversion tends to start from £25,000 and above.

✓ Dormer or L-Shaped Dormer Loft Conversion. These are the most popular types of loft conversion. Dormer price tends to start from £35,000, while the L-shaped dormer starts from £45,000.

✓ Mansard Loft Conversion - This involves replacing the entire side of a sloping roof with a vertical wall and flat roof. It requires a planning permission. The type of loft conversion usually starts from £45,000.

✓ Hip To Gable Loft Conversion - This usually starts from £50,000.

How To Plasterboard A Brick Wall

Do you want to cover your brick wall with plasterboard? The key to success here is the preparation. You must ensure that brick wall is prepared well enough to receive the plasterboard. To get started, there’s the need to attach wood furring strips to the wall which serves as studs in a wood frame structure. This way, the plasterboard will be prevented from getting in touch with the brick. You can always hang pictures or any other forms of decoration in between the gap between the walls. Let’s have a look!

lAttach Furring Strips

• Get a 2 inch by 4 inch wood stud and apply a bead of construction adhesive.

• Using a masonry bit, drill a pilot hole through the wood stud’s base as well as the brick wall.

• Hit a 3 inch fluted nail through the hole using a sledgehammer

• Using a construction adhesive, bind a horizontal 2 inch by 3 inch stud to the upper edge of the wall.

• Using an adhesive, bind the length of a 2 inch by 3 inch stud on its wide side.

• Use a masonry drill to drill a hole on the wood stud and 1 1/2 inches into the brick wall.

• Hit a 3 inch fluted nail through the pilot hole.

lApply Plasterboard

• Hold a plasterboard sheet against the furring strips.

• Use plasterboard screw to hold the drywall sheets in place.

• Use fibreglass to cover the joints where the two plasterboard sheets meet.

• Use a thin layer of the joint compound on the tape. Once done, screw it using a 6 inch taping knife, then allow to dry overnight.

• Use a sandpaper to smooth the joint compound.

• Use a fresh coat of the joint compound to block the holes and joints. Once done, allow the compound to dry.

• Use a light sandpaper to smooth the final coat.

Plasterboarding a brick wall is a simple task but the preparation part must be done right to protect your investment. Therefore, we’d recommend you hire the services of a skilful professional, who can guarantee the best results especially if you lack enough training and experience to carry out a DIY project.

How To Plasterboard A Wall

If you’re looking to plasterboard your wall, one of the essential things to have in mind is that the plasterboard must be hung horizontally and not vertically. Due to the way they’re manufactured, plasterboard sheets normally possess a “grain along the length. This implies that, it’s only when they’re firmly placed perpendicular against the wall that they’re able to achieve their maximum strength. Materials you’ll need to complete this task includes: Tape measure, stanley knife, pencil, spirit level, drill driver or screw gun, surform, drywall screws and handsaw. Now let’s have a look at the wall plasterboarding steps!

• To plasterboard a wall the first step to take is to place each board in such a way to make the edges the centre of the noggins and upright. Also, the the adjoining walls and door openings should fit closely to the edges.

• Work from the door opening to the ending wall. From the the stud’s edge to the noggin’s centre, use your tape measure to measure a cut board and as a rule to mark up.

• Place your spirit level on the marks and use the Stanley knife to run a line along the intended cut. Once done, turn the board on its edge and give a sharp push on the back to split.

• Cut the paper left with the knife after folding the split edge back on itself. This way, you should get a nice and clean edge.

• In its right position, place the board up against the studwork. Install the screws on the board’s edges where a noggin or upright can be seen.

• Mark lines down across the board at the stud’s centre.

• Cut the end boards to length.

• Install the remaining boards as mentioned above. While doing this, make sure the factory edges are together.

• Cut any board extending into an opening and finish the edges using a surform.

We’d recommend you hire the professional services of a plasterer for the best results especially if you lack the necessary training or experience. Plasterboarding a wall can be a tricky challenge and you’d save yourself some time, money and effort by getting it right on the first trial.

How Much Plasterboard Do I Need?

Although many people especially contractors have a tough time estimating the number of drywall or plasterboard needed to complete a project, it’s a rather simple task if all factors are taken into consideration. If you’re able to follow the same procedures taken by professionals to count dry wall sheets, you’ll be in the right direction. Let’s have a look at the procedures to follow!

lTake Square Footage Measurement

• Measure the square footage of the area where the plasterboard will be fitted.

• Multiply the height by the width of each wall or ceiling area.

• Add all quantities to obtain a total square-foot amount.

lCalculate Drywall Sheets

• To calculate the number of drywall or plasterboard sheet is very simple once you’ve gotten the total square footage.

• To get started, simply divide the total square footage of area by 32 (that’s if you are using a 4 by 8 sheets) or you can also make use of 48 to make the division (only if you’re making use of the 4 by 12 sheets).

• The answer you get after the division will give you the full number of plasterboard sheets that’s required to complete the project.

We’d recommend you include an extra 10 to 15 percent of whatever you calculate to take care of the possible odd cuts and wastages. This implies that if your total area is 1600 square feet while incorporating 4 by 8 sheets, simply divide 1600 by 32 which equals 50 sheets, now take 10% of 50 which equals 5, then add back the 5 extra to the 50 sheets earlier calculated to get 55 sheets. If you wish to estimate the cost, simply multiply the number of sheets gotten by the price per sheet. Do not forget to include delivery charges and local taxes.

External cladding will have an impact on a damp problem. However, it’s important that cladding is the last part of a damp treatment, as installing cladding over a damp wall will make the problem worse. Do not cut corners or try to remedy a problem with the cheapest solution, a damp proof course may need to be put in place before cladding.

In a nutshell, a mortgage loan is for the acquisition of an asset, so lenders won’t tend to give you anything else in a mortgage that is going to cover your home renovation costs. When you are applying for your mortgage, your provider will examine the price of your new household. For example, if you’re planning to buy a property for £200,000, but you need another £50,000 to help improve it, you’ll find that your lender might turn you down.

Essentially, with any mortgage loans that you take out on your possessions, the bank or creditor theoretically owns your home till you’ve entirely paid off your loan, which is why it is very unlikely that you will get extra funds from them. There are some mortgage providers who will be willing to add on some building costs, but it is entirely up to you whether to choose it or not.

With most mortgages, banks and other lenders will usually give you a maximum of 95% of what you purchased your property for. That means, that even if you contemplate the household has the probability to be valued at so much more, you’ll have to find an alternative way of paying for the developments you have in attention. So, if the accumulation of extra funds on to your mortgage loan is out of the question, you’ll need to find additional ways of paying for the home developments.

It is well and good if you have the cash saved up, or else, you can explore other payment options which your bank or lender may be able to help you with. There are several methods by which you can collect the cost to pay for the improvements, from personal loans to credit cards or even overdrafts, there are tons of ways to lending money. Keep in mind these are all forms of debt so keep an eye out for the interest rates when you are repaying.