Find a Builder you can trust in Brora.

How To Fit Plasterboard

If you’re planning to renovate your house, then here is a must-read guide! Fitting of plasterboard is a crucial step when it comes to renovation. If you’re bringing down an existing lath and plaster for an upgraded surface or adding a new wall, a plasterboard is required for your project to be a true success. If you’re a novice with no prior practice or experience, you can protect your investment by hiring the services of a professional plasterer to guarantee the best results, the first time. However, we’ve put together this guide to give you an insight on how the plasterboard fitting process is done.

To get started, you’ll need a power drill, hammer, plasterboard nails or screws, broad knife, utility knife, measurement tape, pencil, ladder as well as a joint tape.

Before proceeding, you need to identify the number of plasterboard sheets needed to commence the project by measuring the height and width of the wall as well as calculating the square footage. If you possess a stud timber wall, the steps below will get you the best results.

• Measure the walls and mark the plasterboard where you’ll make the cuts. Start with a full sheet and cut pieces down in such a way that would fit

• Score the front paper of the plasterboard with utility knife. Fold the sheet to get a clean cut through the board and make use of the knife to the remaining paper.

• Place the first sheet against the wall and use an offcut to prevent the plasterboard from touch the floor.

• Make the plasterboard rest snugly against the wall in position and screw it firmly on each stud. Once done, fasten it at all the sheets’ edges and in a line down the stud to make for a firm connection. Follow the same process for the remaining plasterboard sheet till the wall is fully covered.

In recent times, more and more home and property owners are starting to come to terms with the large returns and little investment in cavity wall insulation provides. For a relatively little amount you can achieve a lot, from an increase in your home’s energy efficiency and reduction in heating bills to a huge boost in your property’s resale value and lots more. This makes you wonder how an ordinary insulation can help you achieve so much, right? Well, you’re definitely not alone! Several other potential investors are also eager to know exactly how the cavity wall insulation works to deliver all these juicy benefits. In this post, we’re going to go provide you with a detailed insight on how cavity wall insulation works. Let’s take a look!

Typically, cavity wall insulation works as acting as a shield which prevents the escape of heat from your home. It features a reflective surface which serves as a barrier to reflect heat from one side of the panel, effectively minimizing the amount of heat conduction that escapes through. This protection of your home from heat penetration comes with a couple of benefits with the obvious one being an incredible thermal efficiency. An insulated home or property is able to maintain a much more balanced temperature throughout the year – staying a lot cooler during the summer months and retain the heat generated during the winter months. However, a less talked about benefit is the fact that when an insulation is done during the construction of a house, the whole development phase can be completed a lot quicker. This is mainly because insulation offers total protection against weather conditions which enables internal trades to continue without the need to wait for brickwork or cladding to be completed.

How Much Do Roof Rooms Cost?

The price of your roof room may vary depending on your location within the country. Other factors that can also play a key role in determining the price of a roof room includes the conversion’s type as well as the legal and technical issues it’s currently facing. Usually, the cost of roof rooms will range between £1,200 to £2,000 per square metre. The differences in the price per square metre is influenced by the size of the alterations to the roof, the type of roof room to be constructed, the access, location as well as the finishing type.

• DORMER LOFT CONVERSION.

Here, one of the slopes of a pitched roof is substituted for a box-shaped structure. The outcome is a flat roof space which enables the fitting of full sized windows as well as the incorporation of several appliances. This is quite expensive as it involves a total rebuilding of one roof pitch alongside the complete internal works that are associated. The average cost of a standard dormer loft project will range between £25,000 to £50,000.

• HIP TO GABLE LOFT CONVERSION

Here a vertical brick wall is used to substitute the roof’s slope at the ending part of the terrace on detached buildings. The average cost of this type of roof room will range between £32,000 to £60,000.

• ROOFLIGHT LOFT CONVERSION

This basically involves fitting rooflight windows in the roof. Other improvements include flooring, plasterboarding, strengthening of the existing floor, as well as installation of rooflights. The average cost of this type of roof room will range between £15,000 to £25,000.

• MANSARD LOFT EXTENSION

This roof room can create an extra storey on top of an existing building as it makes a space featuring two or four external walls that are a bit sloped. The average cost of this type of roof room will range between £40,000 to £70,000.

No matter how big or small a building is, it can only be as good as it’s foundation - and that’s a fact! It all starts from the footing and when it isn’t deep enough, unlike badly installed gutters or gapped hardwood flooring, can make the whole building collapse to the ground. Just like any code recommendations, the depth of the footings of your porch is a parameter that must be complied with and adjusted to suit your local code requirements.

As a rule of thumb, you should always dig below the frost line when excavating your footings. At this depth level, the moisture present in the soil will be frozen. Ultimately, this will help the ground to act as a barrier to insulate the soil below the footing from freezing during the cold months. As a result, in regions where the weather is almost always very cold the depth of your footings is expected to be at least 48 inches. But in areas featuring a warm climate, you may be allowed to install your footings on grade.

In addition, it’s compulsory that your footings must be installed at a minimum depth of 12 inches below unsettled soil. However, if you’re constructing the structure into a steep hill’s side or by the side of a retaining wall, it’s required that you maintain the least distance to grade both vertically and laterally. In the event whereby you need to achieve a good lateral barrier, you’ll need to have your foundation dug a lot deeper compared to if it’s on a flat surface. For a more accurate and updated information, you can consult your local building inspection department to get familiar with the requirements in your area.

Finding a builder nearby can have enormous assistance when it comes to your build. Period on site, their familiarity of local planning permission, constructors’ dealers and other local trades are all vital bits of knowledge that you’ll welcome on site.

It is always wise to walk around in your local area or drive to a site where any construction work is going on. It’ll give you a proper impression of the constructors who are active nearby. You don’t have to like their style of work or the project they are currently carrying out – after all, a builder can only produce what’s on the plans in front of them.

Find a Builder Other Tradesmen Recommend

If you’ve had to call an electrician before or a local plumber and liked their work, you can always ask them if they have any builders whom they would recommend. Maximum tradesmen get used to seeing the similar acquainted names from one place to another in the sites they are working on and every so often has favourites for who they like to work with — and who they see as a good source of work.

Always Talk to Previous Customers

Once you’ve found a builder you would like to work with, ask them for a list of previous customers they have worked with; they ought to be glad to offer particulars if they’re self-assured they’ve done an effective job.

Look for a builder online

A decent place to start looking for builders online is on sites like the ours so that you can find quality tradespeople and see genuine reviews from previous customers. Not all online review sites can be trusted to display real reviews.

A double house extension is basically a construction to any aspect of your house that elevates up to offer two floors of space. It can be structured to suit your existing home in two storeys or as a side wing on a taller property. If you’re considering building a double house extension, then estimating the cost is a very important task to do before commencing the project. In this article, we’ll give you an idea of the cost of a double house extension so you can estimate yours accordingly.

The double house extension cost depends on several factors that’s specific to your home as well as your design choice. These includes:

• Location of your property. Places like London and the southeast will generally cost more than the other regions due to higher demands.

• Accessibility of the site. The ease of your site’s accessibility also plays a key role in the price.

• Size of the extension. The more the extension’s size in footprint and square metres, the higher the possible costs.

• Materials used in making the roof as well as the complexity of the roof design.

• Your choice of finishing. These includes flooring window and door frames, glazing, underfloor heating and roof lights.

• Your property’s soil type. Different types of soil requires varying treatments as well as materials to develop solid foundations.

Constructing a double house extension is a quite simple build in terms of technicality when its to the side or rear of your house as this can also help you save some money. Generally, considerably expanding your home’s space by building a double house extension will cost within the range of £1,500 per m2 to about £2,800 per m2.

For 2 metre solid fences it’s recommended to use concrete posts to support each panel. For smaller 1 metre fences or for picket fences with gaps between each timber piece you can use timber posts. A fencing contractor will be able to advise you on the best materials from the length and requirements of a new fence.

How long it takes to install insulation will depend on the size of your property. In general, loft and cavity wall insulation can be installed in a day or two. External wall insulation will usually take longer to install. The rep or installer will be able to advise you when quoting for the job how long this will be.