Find a Builder you can trust in Humberside.

Did you try rendering a wall but it doesn’t turn out the way you would have hoped for? Or perhaps you’ve been watching your wall render gradually deteriorate over time. Regard of your purpose, learning how to repair render cracks on wall is usually a great skill to have with your home maintenance in mind. However, whenever these crack are too large or difficult, we’d recommend you call in a reliable professional who can guarantee the best results for help. In this guide, we’re going to take you through the wall render repairing process. Let’s have a look!

No matter how solid a building material is, over time it’ll yield to the elements. When it comes to wall rendering it may be a case of too much sunshine or a costly mistake in the application process, but in truth, it cracks just because it cracks.

In order to repair render cracks, you’d have to start with a removal of damaged or cracked render. You’ll have to remove all the render or just a small section depending on the area you’re working on. If you’re able to clean all of the existing render as well as the paint over it all (both old and new), then removing a small section would work better as it makes it look neat and redone. Upon the removal of the existing render, the next important step would be to remove all loose material as well. Once done, you can then leave for up to 2 days to allow any trapped moisture to come out. Unfortunately, if the rains you’d have to wait till that dries too before you proceed.

Once dried, you can buy a pre-prepared render mix which already contains cement, lime and sand. Mix a 20kg bag with 4 litres of water (or check the product instructions and follow strictly), the mix to a fine consistency. Render is quick to dry, so you’d want to apply within 30 minutes of mixing. Make use of a trowel to apply the render on the affected spots and blend with the surrounding area.

Driveway surfacing materials like concrete, asphalt and clay brick usually crack because they’ve been exposed to extreme temperatures or put under high pressure. It’s important to repair driveway cracks before they get worse and cause damage to vehicles and perhaps others to trip on raised cracks.

Generally, it’s possible to extend a barn conversion, but there are certain conditions that you’ll probably need to meet. Ultimately, it’s up to your local planning office to decide whether to approve your planned barn conversion extension or not.

Typically, small extensions on the side of a barn conversion are often approved, particularly if they serve to preserve the original character of the barn. This could be because the extension will mimic the appearance of the original structure, or house facilities that would look odd in the original building.

However, you probably won’t be allowed to build a larger extension, or one that isn’t in keeping with the appearance of the original barn.

There are so many benefits that comes with building a porch in your home premises. It’s an extra space where a lot can be achieved such as drying a dripping wet dog, taking off your dirty shoes or boot and lots more. So if you’re considering to construct a porch, it’s definitely going to be a wise decision. However, before you get started, there’s a need to determine if you’ll need planning permission for a porch. It’s important to take note that planning laws are dynamic and can be updated at any point, so be sure only to use trusted sources only as your guide. If you’re the homeowner or landlord, it’s entirely your responsibility to obtain the right approval for any development project you wish to carry out within your premises.

A Porch can not be termed as an extension and neither is it a conservatory, they’re basically built to the home’s front covering the main entrance using a stone base or a brick. As a result, a porch does not need planning permission due to the fact that it’s covered by the permitted development rights if the specific guidelines for porches are complied with. Below are the instances where you WILL need planning permission for a porch.

✓ If the floor space is more than 3sqm (the wall inclusive).

✓ The highest point has a height of more than 3 metres.

✓ If the porch is situated within 2 metres of a boundary directly facing on to the road.

You may need planning permission if the house is a listed building, designated area or falls under an Article 4 Direction.

In order to build a porch without planning permission, you need to consider all the criteria stated above. You can also visit the Planning Portal website to get more detailed information before getting started.

How To Put Up Plasterboard

Putting up a plasterboard is a vital process when it comes to home renovations. However as daunting as it may seem, with a good guide and regular practice you can master the skill within a small period of time. If you lack proper training and experience, we’d recommend you hire a seasoned professional plasterer for help so as to get the best result and also avoid additional costs due to possible damages.

Putting up plasterboard is way quicker than wet plastering and also significantly reduces the drying time that can slow down your renovation plans. With a plasterboard, you can delve straight into the decorating stage and achieve a smooth finish. Below are the steps required to put up a plasterboard.

• The first step is cutting the plasterboard to shape which be one of the most challenging parts of the process. This is because you’ll need to fit the board around things such as plug sockets and window sills. As a result, this involves cutting complex shapes rather than just a simple straight line. To get this done, simply mark out the cut required with the use of a tape measure, combination square and spirit level for a better precision. Once done, you can then use a plasterboard pad saw to cut along the marked spots.

• After you made the required cuts, the next step is putting up the plasterboard. And depending on where the boards are going to be put, this could be a very challenging task. If you’re going to put the boards on the ceiling or somewhere very high up, you’d probably need an extra pair of hands for help. To get this done, use the appropriate screws to secure the boards in place if you’re installing them directly on studs. However, if you’d be fixing them onto bricks or blocks, a drywall adhesive is your best bet.

How To Dot And Dab A Plasterboard

If you want a fast and simple way to achieve a smooth and sturdy wall which is decoration-ready, then dot and dab plasterboard is the way to go! It’s a relative simple process but can also be a bit challenging. Therefore, if you lack the necessary training or experience, hiring a professional would be a great step to protect your investment and guarantee the best results. Here, we’ll provide you with a deep insight into the plasterboard’s dot and dab procedures. Let’s have a look!

• At the thickness of the board with the adhesive, mark the ceiling and floor as well as the wall to indicate the centre of each board.

• Ensure the wall’s height is 15mm more than the plasterboard

• Make a mixture of the adhesive and achieve a thick consistency. Apply a consistent layer of the mixture around the wall’s perimeter, edge of the ceiling and any other openings with the use of a trowel.

• Select dabs that are about 250mm long and 50mm to 75mm wide and apply the adhesive in them. Make use of 3 vertical rows for individual boards. Also ensure to apply, at skirting level, a band of adhesive.

• Position the board’s reverse side against the dabs, and laying against the packers. Then make the board align with the ceiling and floor marks with the help of a straight edge.

• Raise the board till its tight against the ceiling with a board lifter. Once done, use the plasterboard to wedge the board into place before you remove the board lifter.

• Repeat the same process for the remaining parts of the room. Once completed, make sure the adhesive is set before you remove the boards.

Do you want to inject a new lease of life into your home or property, or transform it into a more modern style that better suits your taste? Or perhaps you’re only looking to add more value to your property to enable you sell for a profit in the nearest future. Regardless of your purpose, determining the cost of your home renovation can be incredibly difficult. However, you can still obtain a reasonable budget for the project with proper planning as well as preparation. It’s almost impossible to get an exact figure for any home renovation cost, however, this article aims to give you a good idea of cost range to enable you make informed decisions.

The cost of renovating a house can vary significantly depending on a wide range of factors. Some costs are fixed while others may vary greatly. As a result, if you want to have a more exact figure, you’ll have to call in a professional beforehand to give you an idea of how much they’ll charge. Below are some of the most significant costs you’ll most likely face during property renovation.

✓ Administrative cost. Asides from material and labour, the administrative costs is another important cost you’ll need to factor in. The first thing here is usually insurance, this is because all regular building insurance policies does not cover large scale renovation projects. So if what you’re planning is a huge structural change to your property, then it’s more likely that it won’t be covered by your buildings insurance policy. In this event, you’ll have to take out a specialist renovation insurance.

✓ Planning permission and property renovation. This is another potential cost you’ll have to factor in. Submitting a planning application in the UK usually ranges between £200 to £250.

✓ Adding an extension. Generally, a 4m by 5m extension would cost within the range of £30,000 to £40,000.

How Much Does It Cost To Have A Loft Boarded?

More often than not, several homeowners fail to realize there’s so much value sitting right under their roof - the loft. When a loft is boarded, there are so many juicy benefits that can be derived. It can be used as a storage room, spare bathroom, home office and several more functions. Therefore, if you really wish to maximize the space under your home’s roof, you’d have to considering boarding it. So how much would it cost to have your loft boarded? Here, you’ll discover the cost of boarding your lofts so you that you can set a budget and start to plan.

The cost of boarding a loft is actually affordable for several individuals, simply because you’re allowed to floor as much or as little as you require. And while you’re up there flooring and fitting the loft boards, you can as well decide to upgrade the insulation of the loft too. This way, you be able to prevent heat from escaping through the roof of the house which helps improve energy efficiency and ultimately, save you some money on heating bills.

If you’d prefer to make it a DIY project, the cost of 18mm chipboard is about £8 to £10 per sheet sized 2400m x 600m. Meanwhile the insulation boards should range between £18 to £22 for a sheet.

For a professional service, you’ll be provided with a quote for both the materials and labour. The amount will be based on the number of boarding required as well as the method selected. For an average storage space needs, flooring size of about 15m2 is suitable. The price for this quantity would be between the range of £50 to £700 for the counter barren method or above £1000 for a more sophisticated method.