Find a Builder you can trust in Isle Of Canna.

When it comes to laying of bricks, it is essential to get the right mortar mix. It is vital, be it for construction or maintenance projects, so far mortar is required. There are several materials incorporated in getting mortar which includes both cement and sharp sand, soft sand or plasterer’s sand and lots more. Here, we are going to look at the right ratio for cement and sand mix in bricklaying.

Cement include ingredients such as iron, aluminium, as well as silicon and it is mainly used for mortars like aerated cement mortar, Portland cement mortar and gauged mortar. Sand, on the other hand, comes in different forms such as sharp sand, soft sand and plasterer’s sand. The sharp sand consists of a larger grain size than the others and is usually incorporated in the construction areas that requires more strength as well as flexibility. Soft sand is the most common one used in mortar and it’s also referred to as bricklayers’ sand. These are used to make all types of mortar. Finally the plasterer’s sand which neither has the sharp sand’s coarseness nor the fineness of the soft sand, but can also be used for any form of mortar.

Cement and sand mortar is used for a plethora of bricklaying jobs serving as a glue for bricks, walls and pillars, while also repairing or maintaining old listed buildings. The preferred ratio here is 1:3 to 1:5 of cement and building sand. Meanwhile, to get a sand cement mix, essential materials that are required includes water, soft building sand as well as cement. However, you must also note that a sand and cement mortar is not used for structural projects, rather a concrete ratio is used.

Cutting a plasterboard is a relatively simple process requiring only some basic tools. Unfortunately, the lack of knowledge serves as big deterrent for many people who wishes to put it to good use. Plasterboard can actually be sawn using an ordinary timber saw that’s fine-toothed to get a cleaner edge. However, the basic tools you may also need includes a sharp knife (Stanley Knife), pencil, a fine sandpaper, a straight edge and measurement tape as well as a wall board saw. Let’s have a look at the cutting process!

• Firstly, you need to put the plasterboard sheet flat on a firm surface.

• Use the tape measurement to measure the cut you wish to make.

• With the help of a pencil, simply mark out the part you wish to cut on the plasterboard’s front side.

• Once marked, place a spirited level over the marked spot on the plasterboard sheet you want to cut.

• Cut a shallow mark into the plasterboard sheet using the Stanley Knife to cut along the edge.

• The cut should be slow and gradual to ensure you do not wander off the edge of the marked area.

• Once the shallow cut has been made, turn the plasterboard sheet on its edge and deliver a quick and sharp push towards the plasterboard’s back and on one side of the cut.

• Place the plasterboard sheet backing against a flat surface ensuring the line of the cut is over an edge. Once done, give a quick and sharp push towards the back of the plasterboard sheet and on the part of the board is reaches beyond the edge.

• Using a fine sandpaper, remove all forms of paper burrs.

The process of cutting plasterboard requires a lot of practice. If you lack the training and experience, the cutting process is best left to a proficient professional who can guarantee the best results the first time and save you some additional costs due to potential damages.

This is a type of loft conversion that extends your roof on the sloping side. It is a great option to go for especially where a hipped roof effectively makes the usable floor area a lot smaller which can be a tricky affair when it comes to putting in a new staircase. Here, the roof is extended from the current ridge in such a way that it effectively fills the gap between them. As a result, this turns the hip (in a hipped roof) into a gable to create space in your roof for a loft conversion - hence the name “hip to gable.

The new gable can be done in whatever way that suits both your taste as well as your property. You can make the new gable construction in woods and then tiled to match your existing roof while you can also go for other options such as brick block pebbledash or rendering. You are also free to fit in a new window into the loft conversion end so as to allow for natural light into the loft space.

A hip to gable loft conversion is mostly found on both semi detached and end terrace buildings, particularly those constructed in the 1930s. Overall, this type of loft conversion is particularly ideal for homes that features a hipped roof and with a sloping roof at the side of the property. Some detached properties can also possess a hipped roof on the side - and as such, a double hip to gable loft conversion can also be deal as it’ll create more loft space for usage. If your home fits into the bill, then you should be aware that once the project is completed, you’ll have plenty of usable space available to both you and your loved ones.

How To Plasterboard A Brick Wall

Do you want to cover your brick wall with plasterboard? The key to success here is the preparation. You must ensure that brick wall is prepared well enough to receive the plasterboard. To get started, there’s the need to attach wood furring strips to the wall which serves as studs in a wood frame structure. This way, the plasterboard will be prevented from getting in touch with the brick. You can always hang pictures or any other forms of decoration in between the gap between the walls. Let’s have a look!

lAttach Furring Strips

• Get a 2 inch by 4 inch wood stud and apply a bead of construction adhesive.

• Using a masonry bit, drill a pilot hole through the wood stud’s base as well as the brick wall.

• Hit a 3 inch fluted nail through the hole using a sledgehammer

• Using a construction adhesive, bind a horizontal 2 inch by 3 inch stud to the upper edge of the wall.

• Using an adhesive, bind the length of a 2 inch by 3 inch stud on its wide side.

• Use a masonry drill to drill a hole on the wood stud and 1 1/2 inches into the brick wall.

• Hit a 3 inch fluted nail through the pilot hole.

lApply Plasterboard

• Hold a plasterboard sheet against the furring strips.

• Use plasterboard screw to hold the drywall sheets in place.

• Use fibreglass to cover the joints where the two plasterboard sheets meet.

• Use a thin layer of the joint compound on the tape. Once done, screw it using a 6 inch taping knife, then allow to dry overnight.

• Use a sandpaper to smooth the joint compound.

• Use a fresh coat of the joint compound to block the holes and joints. Once done, allow the compound to dry.

• Use a light sandpaper to smooth the final coat.

Plasterboarding a brick wall is a simple task but the preparation part must be done right to protect your investment. Therefore, we’d recommend you hire the services of a skilful professional, who can guarantee the best results especially if you lack enough training and experience to carry out a DIY project.

When it comes to extending a home, the rear of the house often comes to mind a lot more than the front. However, this doesn’t mean that you can’t extend the front of your house. This can be done either as part of a renovation project whereby the entire house is incorporated or it can also be done in isolation. It’s possible to extend the front of your house without the need to apply for a planning permission, however, there are a bunch of limitations you’d have to comply with if you wish to carry out with such a project. Sometimes, this may imply that extending to the front of your home is more tedious and tasking than extending your home’s rear. So exactly how far can you extend the front of your home without planning permission?

The short and simple answer to this question is 2 metres square area with a height not more than 3 metres. Generally, you do not need a planning permission to build a front porch as long as its area doesn’t go beyond 2 square metres from a public road or walkway. Also, a tiled or slated roof can be as much as 4 metres but other roofs must not go beyond 3 metres in height. If you want to extend the front of your home beyond the restrictions specified, then you’ll have to apply for a planning permission.

Extending the front of home can be quite costly, but this can be controlled by not building to the extension to the highest specification, not including an extension on kitchens or bathrooms and more.

If your basement has a cavity drain membrane, it’ll need a pump to move water away from the exterior of your basement and prevent flooding.

Sump pumps can be noisy, but they don’t have to be. Generally, if you have a well-designed pump that’s installed correctly, you shouldn’t find it a problem. For best results, hire a skilled, experienced professional to supply and install your drainage system.

In the event whereby you’ve got big refurbishment ideas for your house but a small budget, then you know it’s time to be a bit more creative and apply some cheap and simple tricks. The best possible way to go about this is to invest time in acquiring new skills rather than trying to save up more money to pay a pro to deliver the results you want. After all, the most significant cost when it comes to house refurbishments is usually the labour cost.

The key to making cheap tricks a lot effective in the refurbishment process is by undertaking small tasks that’ll make a huge impact. A great way to start would be by taking it one task at a time rather than rushing to complete all at once. This way, you’ll have enough time to perfect your skills before moving on to the next.

✓ Paint the interior walls. Although this is a simple task but it’ll save you a lot of money if done as a DIY project. To get started, you’d have to text colour options by painting samplex on the wall first. Once done, you can go for the one that adds warmth, dynamism as well as energy to the room.

✓ Fix up your furniture. This involves re-upholstering and refinishing any piece of furniture that appears tired or overly worn (you can leave out the ones that you do not really like or unnecessary items).

✓ Spruce up small but important items used on a daily basis. This includes spray-painting inexpensive picture frames, recovering lampshades with a vibrant paper or patterned fabric, adding throw pillows to armchairs and couches and the likes.

✓ Fix all small things that are broken. This includes activities like patching the nail holes in the wall, repairing the latch on the kitchen cabinet, fixing the gutter, putting a new handle on the door and lots more.

External cladding will have an impact on a damp problem. However, it’s important that cladding is the last part of a damp treatment, as installing cladding over a damp wall will make the problem worse. Do not cut corners or try to remedy a problem with the cheapest solution, a damp proof course may need to be put in place before cladding.