Find a Builder you can trust in Totland Bay.

There are so many benefits that comes with building a porch in your home premises. It’s an extra space where a lot can be achieved such as drying a dripping wet dog, taking off your dirty shoes or boot and lots more. So if you’re considering to construct a porch, it’s definitely going to be a wise decision. However, before you get started, there’s a need to determine if you’ll need planning permission for a porch. It’s important to take note that planning laws are dynamic and can be updated at any point, so be sure only to use trusted sources only as your guide. If you’re the homeowner or landlord, it’s entirely your responsibility to obtain the right approval for any development project you wish to carry out within your premises.

A Porch can not be termed as an extension and neither is it a conservatory, they’re basically built to the home’s front covering the main entrance using a stone base or a brick. As a result, a porch does not need planning permission due to the fact that it’s covered by the permitted development rights if the specific guidelines for porches are complied with. Below are the instances where you WILL need planning permission for a porch.

✓ If the floor space is more than 3sqm (the wall inclusive).

✓ The highest point has a height of more than 3 metres.

✓ If the porch is situated within 2 metres of a boundary directly facing on to the road.

You may need planning permission if the house is a listed building, designated area or falls under an Article 4 Direction.

In order to build a porch without planning permission, you need to consider all the criteria stated above. You can also visit the Planning Portal website to get more detailed information before getting started.

Windows or lightwells can be a great way to introduce natural light into your basement, making it a more valuable, enjoyable space. However, they’re not always an essential requirement.

It’s important for your basement conversion to meet ventilation and fire safety building regulations. Windows can be a good way to do this, but they’re not the only option. Stack or mechanical ventilation, or ensuring that stairs up from your basement connect to an exit can be a good alternative.

So, while windows can be a great asset to your basement conversion, if you can’t afford them or they’re not structurally feasible, you can still create a basement conversion without them.

Finding a builder nearby can have enormous assistance when it comes to your build. Period on site, their familiarity of local planning permission, constructors’ dealers and other local trades are all vital bits of knowledge that you’ll welcome on site.

It is always wise to walk around in your local area or drive to a site where any construction work is going on. It’ll give you a proper impression of the constructors who are active nearby. You don’t have to like their style of work or the project they are currently carrying out – after all, a builder can only produce what’s on the plans in front of them.

Find a Builder Other Tradesmen Recommend

If you’ve had to call an electrician before or a local plumber and liked their work, you can always ask them if they have any builders whom they would recommend. Maximum tradesmen get used to seeing the similar acquainted names from one place to another in the sites they are working on and every so often has favourites for who they like to work with — and who they see as a good source of work.

Always Talk to Previous Customers

Once you’ve found a builder you would like to work with, ask them for a list of previous customers they have worked with; they ought to be glad to offer particulars if they’re self-assured they’ve done an effective job.

Look for a builder online

A decent place to start looking for builders online is on sites like the Federation of Master Builders. They have a search tool where you can find precise crafts in your area and look at their situations. All FMB members are assessed and individualistically examined and are checked to ensure that they have the correct insurances in place.

Generally, a paved driveway is always subjected to regular usage and yours isn’t likely to be an exception, otherwise you won’t be here. Regular usage automatically necessitates regular maintenance of the driveway in order to extend its lifespan, make your property safer and add more value to it. This maintenance will involve a frequent inspection of the paved driveway so as to identify and repair divots, cracks as well as rutting. Paved driveways usually have a lifespan ranging between 15 to 20 years, but this can only be guaranteed when backed by regular maintenance activities. Failure to provide your paved driveway with a regular maintenance will lead to a rapid deterioration within just a couple of years after installation.

The issues commonly faced by paved driveways is usually different based on several factors such as the weather, your location, your property’s sub base as well as some other elements. The ability to identify the problems and solve or repair them on time is key to success while it’s also save you some time and money. In this article we’re going to look at how to go about do-it-yourself tasks that involves minor cracks. More intense damages are advised to be handled only by professionals.

✓ Prepare the area. Clear the debris, weed the plants or vegetation (if any).

✓ Use a strong spray from a garden hose to wash clean the cracks

✓ In the event whereby the crack is deep, simply fill it until it reach about a quarter inch of the surface with sand.

✓ Tamp down the sand to make it more compact.

✓ Apply a patching compound to the surface of the cracked paved driveway.

✓ Leave it for some time to cure.

✓ Once cured, you can then apply your sealant.

With the title of this blog, do not be deceived into thinking the purpose is to encourage you to install an external insulation by yourself. Even as a competent DIYer, it’s not advisable to buy a couple of materials and start slapping it into the wall hoping for the best outcome. External insulation is by no means a DIY job and without the proper training and experience, it can easily turn out disastrous resulting in loss of time, effort and money in such a valuable project. This blog, however, will give you a great insight on how the installation process works and help maximize knowledge ensuring you do not spend more than necessary.

External Insulation Installation

lRender Test

• This is done to ensure the existing render is good enough for insulation support.

• If positive, the insulation can be applied directly onto it.

• If negative, ensure removal of the old render before fitting the insulation.

lPipework Adjustment & Removal

• Remove all pipework prior to insulation fitting

• Install temporary downpipes to ensure water is not wasted and everything continue to function normally during the insulation fitting process.

lWindow Protection

• Protect the window with a protective layer or film.

lStarter Track Fitting

• Determine level you want the insulation to start (height).

• Fit the aluminium start track or carrier tray at the identified level.

lInsulation Boards Fitting

• Apply a layer of adhesive to the board and glue them to the wall in a staggered pattern.

• Cut to fit round all obstructions and windows.

• File off the edge of the board where necessary using a rasp upon successful fitting of the boards

lMechanical Fixing Inclusion

• Hammer around 10 fixings per square metre into the board.

• This is to secure the insulation boards.

lBeading Fitting

• Add corner beads and stop beads to ensure the insulation is secure and to prevent it from making contact with other materials.

lReinforcing Mesh & Render Addition

• Apply two layers of strengthening properties and between the two layers of render, include a fibre glass mesh.

lPrimer Application

• Paint on the primer

lFinal Render Application

• Choose your most preferred texture and colour as this will be the last coating of the installation process.

lPipework Re-installation

• Re-install all detached pipework at the start of the installation process.

If you’re considering converting a barn or buying one, you shouldn’t need to worry about it being cold. This is because building regulations dictate that when you convert a barn, you need to insulate it to meet specific standards. However, it’s worth considering its heating system and ceiling heights carefully – some barn conversions are likely to take longer and be more expensive to heat up than others.

If you’re thinking about refurbishing your house or property but don’t know how to go about it, then you’ve come to the right place. In truth, not every home refurbishment works goes in exactly the same order, however it’ll do you some good to abide by a specific plan in order to avoid both unnecessary works as well as expenses. For instance, how would it feel if you have already closed walls and paint only to realize that there’s a need to include a new plumbing stack that has to go behind the wall? Not good, right? Well, this guide is designed to help you avoid such frustrating situations. Let’s have a look!

✓ Establish a plan. This involves carrying out a good assessment of what you’d like to refurbish and set the priorities like deciding where to start and making sure you have both the time and budget to complete the project.

✓ Set a budget. Establish a final amount that’ll be the threshold to your spending. It’s always good to add an additional 10% to 15% to cover unexpected costs.

✓ Hire a contractor. Carry out a research, reach out to many contractors, compare their prices, work quality as well as integrity before hiring.

✓ Talk to your insurance company. Find out if you have the amount of coverage that suits your needs from your insurance company before and after your project.

✓ Secure permits and order materials. Make sure you check with the latest regulations before commencement. Once done, you can start ordering the required materials.

✓ Start demolition. This is optional as it only applies if space is being added.

✓ Work behind the walls. This include doing all the works necessary behind the walls like plumbing, electrical, heating etc.

✓ Paint and install flooring

✓ Fit in the cabinetry

✓ Add finishing touches. This includes the last details and decorations.

Any residential building work requires a general builder. The term Residential building work means any work which is involved in building a house or changing or adding to a home. It also comprises of mending, refurbishing, ornamenting or applying shielding treatment to home. A dwelling is defined as a building or a part where people live. This might include an apartment, house or a townhouse.

Here is a list of some of the works that require a building licence:

• construction of a garage, carport or a shed

• renovation for bathroom, kitchen or laundry

• structural landscaping and building swimming pools

• construction of conservatories and atriums

• house lifting for example, raising the height of an existing structure permanently

• removing and resitting dwellings

• steam rooms and saunas.

General building contracts might also involve work that needs a specialist. These works can be appropriately subcontracted. However, this work must be carried out by the container of a permitted contractor licence or competent administrator certificate in that specialist category.

There are a number of different categories of licences that are available depending on whether you want to oversee the work or have an agreement with another party. When you have a contractor licence, you will have the option of submitting a contact to bid on the work. You can only do the categories of work designated on your licence card. Contractor licences can be allotted to people and businesses and partnerships.

With a certificate of a qualified supervisor, you will be able to supervise the type of work specified in the certificate. Such certificates are only issued to individuals and do not allow you to contract for work.

The licence of an endorsed contractor is issued to those individuals who have applied for a contractor licence but also possess the necessary qualifications and experience to become a qualified supervisor.