Find a Builder you can trust in Gorebridge.

Due to the fact that we live in a country (the UK) with so much history as well as architectural beauty, there’s a need to have what’s commonly called “Conservation Area. A Conservation Area is basically an area which is designated by the local authority and is established in order to protect and enhance areas of historical and architectural interest which includes both rural and urban areas. Therefore, when it comes to refurbishment project in a conservation area, there’s usually a lot of things that needs to be put into consideration as well as hurdles to scale in order to make alterations to your property without any interruptions from the law.

In general, all properties in a conservation area have strict regulations governing the outlook of the houses, as this plays a major role in the appearance of the area as a whole. As a result, if you wish to bring down a building, fence, wall or even railing and the likes, you’ll need to obtain prior consent before you proceed. An easy way to go about any refurbishment plan is to to ensure the usage of exactly the same materials that exists in the current house. When you abide by the rules, you’ll be in a more favourable position to acquire the needed prior consent.

The short and simple answer to the question is yes, you can refurbish a house in a conservation area but subject to the approval of the local authority through a planning permission. And when it comes to submitting a planning application for approval, some are aspects will usually be subjected to more intense examinations than the others. Hence, the need to make sure that your refurbishment plans are all friendly in a similar way to the neighbouring buildings and environment.

Aside from the cold weather not being the most pleasant condition to work in, the winter weather can also cause a lot of problems for construction workers and even more so when you’re working with render. Poor weather conditions can generally cause a lot of harms on the final finish of a render. Below are some of the reasons why you should not consider rendering in a bad weather.

✓ Lime bloom. Render can be impacted by lime bloom as they are subjected to damp conditions and low temperatures while curing. This is due to the fact that cement are intolerant to slower drying conditions especially immediately affect its application.

✓ Top coats can be compromised. Coating are likely to get washed off before they’re even afforded the chance to set if drying conditions are low.

However, because its cold out there doesn’t necessarily imply that work must stop. It’s very possible to render during the winter months but to avoid potential pitfalls, we’ve got some tip that can be of great help. Let’s have a look!

✓ Check the weather forecast. Determine the drying and curing time and watch the forecast for the temperature dropping at night.

✓ Select the most suitable render. There are renders that are suitable for application in low temperatures to about 5℃ or even as low as 1℃. These types of render are fast setting which makes them perfect for the cold condition.

✓ Watch out for frost. Frost and render are enemies. Therefore, it won’t be wise to work with frosted materials, on frosted subtrates or apply below the recommended temperature that’s written on the product’s datasheet.

✓ Protect the finish. Make use of artificial enclosures around the scaffolding to battle adverse weather conditions.

When your driveway is suffering from depression, it becomes unsafe for driving (a danger zone) and ugly - no homeowner wants that! Unfortunately, most driveways won’t hold flat for long as they tend to develop cracks and potholes pretty quickly. Here, we are going to take you through how to fill asphalt driveways’ depression so as to ensure the sinkholes in your driveway poses no threat to you or your loved ones, while also beautifying your property. The approach to be used depends on the intensity of the depression. If its only a few cracks and holes, this can easily be repaired with some equipment. But if otherwise is the case, then calling a reliable professional will be your best bet. In this article, we’ll show you how to repair dips in your asphalt driveway relatively quickly.

✓ Pick a date with warm and sunny weather. This is because if you work in a cold weather, chances are the materials will freeze and hence, unusable. So find a day when the temperature will over 50 degrees Fahrenheit and below 80 degrees Celsius and when there would be no rain. We’ll advise a day between May to October.

✓ Prepare the area. Remove all loose stones, soil, dirt as well as vegetation from the holes. Once done, you can then proceed to washing the area with a pressure washer or sweep with a broom.

✓ Apply a thin mixture of asphalt to the area. Use a flat stirring stick to coat the low driveway area with a thin mixture of asphalt.

✓ Tamp the asphalt repair mix. Purchase the right kind of asphalt to repair the driveway. Fine aggregate asphalt mixture is more suited to filling small holes, whereas the coarse aggregate is more suited to filling larger holes. Apply layers ( about 2 inches each time) of the asphalt repair mix to the sunken area and use a shovel to give it a smooth finish. Once done, simply make the area smooth and protect it with a piece of plywood. Do not walk or drive on the area for a couple of days.

How To Lay Loft Boards

Do you need more storage space in your home or property? If you live in a tiny space especially where extensions can’t be made sideways, why not look to the topmost area of your home and consider boarding out your loft to make it usable?

Boarding your loft can make for a fairly easy DIY project but like every other home improvement tasks, it requires some specific skill sets as well as knowledge for a successful construction. Therefore, we’d recommend you hire the services of a reliable professional in order to guarantee the best possible outcome, especially if you lack proper training or experience that’ll help you avoid some costly mistakes. Here, we’ll give you a good insight into the loft board laying procedures.

• Get The Right Tools & Equipment

The materials and supplies you’ll need to lay loft boards include loft boards, screws, tape measure and pencil, drill, hammer, saw, protective gear such as gloves and dust mask.

• Work Out The Area

Measure up the area you need the boards to cover. The standard loft features two different sizes (both are 18mm thick) which include 2400mm x 600mm and 1220mm x 320mm. You should ensure that the board you opt for fits through the loft hatch perfectly.

• Start Laying

Once you’re done working out the area, the next step is to put on your protective gear and start putting the boards in place. You should lay the boards in a staggered pattern so as to give a better strength. While doing this, watch out for any wire running through your loft so they don’t get trapped, you should also cut the boards for easy access to the light fittings’ top.

• Make It Permanent

Upon the successful placement of the boards in a way that offer a safe area to store things and stand on, you’ll have to screw them in place. Start by drilling 2 or 5 holes along the edge of individual boards in such a way that lines up with the centre of the joist below. Once done, then you can fix them in place with screws.

Cutting a plasterboard is a relatively simple process requiring only some basic tools. Unfortunately, the lack of knowledge serves as big deterrent for many people who wishes to put it to good use. Plasterboard can actually be sawn using an ordinary timber saw that’s fine-toothed to get a cleaner edge. However, the basic tools you may also need includes a sharp knife (Stanley Knife), pencil, a fine sandpaper, a straight edge and measurement tape as well as a wall board saw. Let’s have a look at the cutting process!

• Firstly, you need to put the plasterboard sheet flat on a firm surface.

• Use the tape measurement to measure the cut you wish to make.

• With the help of a pencil, simply mark out the part you wish to cut on the plasterboard’s front side.

• Once marked, place a spirited level over the marked spot on the plasterboard sheet you want to cut.

• Cut a shallow mark into the plasterboard sheet using the Stanley Knife to cut along the edge.

• The cut should be slow and gradual to ensure you do not wander off the edge of the marked area.

• Once the shallow cut has been made, turn the plasterboard sheet on its edge and deliver a quick and sharp push towards the plasterboard’s back and on one side of the cut.

• Place the plasterboard sheet backing against a flat surface ensuring the line of the cut is over an edge. Once done, give a quick and sharp push towards the back of the plasterboard sheet and on the part of the board is reaches beyond the edge.

• Using a fine sandpaper, remove all forms of paper burrs.

The process of cutting plasterboard requires a lot of practice. If you lack the training and experience, the cutting process is best left to a proficient professional who can guarantee the best results the first time and save you some additional costs due to potential damages.

Whether a basement is worth converting depends on your location and how much work it requires.

A basement conversion can be a great way to add space to your home, and can raise your property value. However, it can also be one of the most expensive ways to do this, so if there’s a possibility to extend your property, or convert a loft or garage, it’s worth considering this first.

You should also compare how much your basement conversion will cost with the amount it could raise your property value by. In some areas, a quality basement conversion could earn you money in the long run, but in others it’ll only cost you. If you’re planning on staying in your property for a long time this might not matter to you, but if it’s not your forever home then it’s an important thing to think about.

What is your garage being used for? If your answer is anything besides your vehicle, you’re in the majority in the UK. In the country, according to a research by Admiralty Loans, several home and property owners now use their garage as dumping ground for all sorts of stuffs asides a car. Ultimately, this gives rise to garage conversions as the more or less underutilized space can be converted into a living space which can be more beneficial while also adding more value to the property.

A garage conversion is a fast and relatively affordable route to adding more floor space within your home. It’s basically the act of changing your garage into something other than a storage or a place in which you can park your car. This can be anything from a bedroom to a playroom and anything in between. It’s a great way to provide extra space to allow your family to spread out and have more privacy while still within the walls of your home.

A garage conversion project is a huge one which mostly does not require a planning application so far the conversion is internal. However if you’re planning to increase the garage’s size or change the exterior of your home, or convert your garage into a separate room, then you may require a planning permission before getting started. It’s always wise to consult your local authority before carrying out any work to be on the safer side.

A project of garage conversion’s magnitude is better left to a reliable professional who have the experience when it comes to dealing with building regulations and more. This way, you’d also get to save yourself some headaches and some extra cash which may result from possible costly errors.

Driveway surfacing materials like concrete, asphalt and clay brick usually crack because they’ve been exposed to extreme temperatures or put under high pressure. It’s important to repair driveway cracks before they get worse and cause damage to vehicles and perhaps others to trip on raised cracks.