Find a Builder you can trust in Stornoway.

Yes, bricklayers can work during the cold months, but it all depends on the type of work involved. For instance, residential housing maintenance works such as tuck pointing deficient mortar joints on exterior walls and columns as well as rebuilding of chimneys are best tackled during summer or simply put, the warmer months of the year. This is is mainly because the best results for these activities are achieved in the warmer months and several bricklayers will agree to this fact.

Mixing of mortar using anti-freeze technique to counter-act the effects of a cold weather can lead to white marks trailing down the brick when warmer temperatures comes knocking. As a result, even mortar mixing should be done at temperatures exceeding zero degree farenheit which will hold no serious consequences if the temperature should change to a little bit below the norms. During the winter, a good technique that can be incorporated to when mixing mortar would be to mix them in smaller quantities in a warmer environment. These small quantities will immediately be fed by the labourers to the bricklayers and in such circumstances, the mixed mortars will not be subjected to a freezing temperature for too long.

Generally, it would be very unwise to consider any bricklaying work to be done whenever the temperature jumps to a certain level which would be considered to be very inconvenient to work in. Interior works like remodelling of fireplaces can be tackled so long there is a warm space to mix the mortars while also keeping the materials at an indoor temperature. Bricklaying works that have, however, been completed during the colder months should be subjected to a very close inspection as well as looking for potential damage that can be caused to existing works as a result of the harsh weather.

When Does A Loft Become A Habitable Room?

When a loft is being converted to functional space, there are a multiple options it can offer. It’s not uncommon that at the conversion of this space, many household may not have a specific plan on how it’s going to be used. However, they know later on an actual need might arise, perhaps as you start working from home, developing other hobbies that requires an extra space or the family grows.

The loft can easily be converted into a game room, study room, playroom or even a household’s “breathing space etc. However, when the family grows and you wish to make use of the space on the top of your home as an extra bedroom, there are many factors to consider. The fact is, just because there’s enough space to fit a bed, doesn’t make it habitable. For a loft to become habitable, it must be built specifically for the purpose of being a sleeping area and must also comply with the relevant building regulations. It’s as a result of this, many property sale particulars include “potential third bedroom, subject to regulations statement written on it as well as the boarded and insulated loft space’s dimensions.

Loft conversions building regulations are set in such a way to ensure that adequate attention is given to both safety and structural elements to build a new space that’s fit for undetermined household use. These regulations are established minimum requirements to guarantee the following:

• The new floor and ceiling’s structural integrity.

• The existing roof and party wall modification’s structural stability.

• Safety during fire incidents plus an escape route.

• An appropriate stairway access.

• The proposed changes’ structural suitability to the external environment in association with the local area as well as any unique factors specific to the property.

The holy grail of home extensions is basically the need for additional space for living as well as leisure. However, before commencing your home extension project, you’d probably want to know just how big your new building can be. In this article, you’ll find the answer to this question which is also frequently asked by many other home or property owners in the UK.

Besides your budget, there are two other major influencing factors that can determine just how much extra room that can be added. These factors include whether you wish to carry out the extension project under Permitted Development rights which is usually for a smaller project or you’d prefer to opt for a larger project which is covered by Planning Permission.

Apart from the limitations in the size of an extension under Permitted Development, the extensions are also a lot more affordable and consumes less time when compared to the extensions under planning permission. So what exactly is the size limit for an extension under Permitted Development and the ones under Planning Permission?

For a single storey extension, the maximum size that can be constructed without having to submit an application for Planning Permission includes:

• An extension should have a maximum length of 6m, if you reside in a terraced home or a semi-detached property.

• Extensions for detached properties can have a maximum length of 8m.

• The extension built must not go beyond half your garden’s area.

• The extension should have a maximum height of 4 metres, but in the event whereby the extension is situated within 2 metres of the boundary of your property, it should not exceed a height of 3 metres.

• The extension should not be higher than the highest part of the existing house’s roof.

Insulating your loft roof comes with a wide range of benefits. Not only do you get to maintain a comfortable temperature in your house for longer, but you’ll also get to cut down on your heating bills. If you wish to insulate your loft roof, you’ve come to the right place! This process can be very tedious and time consuming especially if you don’t what you’re doing or lack the required confidence to pull it off. It’s advisable to hire the services of a reputable professional who can guarantee the best results for help and also save you some time and money that can come from potentially costly errors.

Before you start rolling out, you’d have to make sure that all cracks, gaps and holes in the ceiling are filled with either a standard filler or decorators caulk. You can also clean between between the gaps in the joists thoroughly. And finally, check for hazards that can cause you problems before getting stated.

• Remember to leave ventilation gaps as you start from the eaves. Then work towards the loft’s centre, starting from the point furthest from the hatch.
• Lay the first layer between the joists which should be 100 mm and then the subsequent layer should be 170 mm to make it up to the recommended 270 mm.
• Carry the electric cables above the insulation and work around visible light fittings.
• Cut the roll in the centre of the floor when rolling out from the eaves on both sides with the help of a craft knife. Ensure that there are no gaps between the insulation and the joists’ edges.
• Lag pipes as you go in order to prevent walking over the insulation to get back to them.
• Ensure that the loft is totally insulated
• Insulate the hatch.

Typically, loft conversions do not require planning permission except in certain situations. They’re usually covered under what’s known as Permitted Development. Certain building works like loft conversion, rear extension and conservatories are granted planning permission by local authorities. Permitted Development, however, gives you a free range to improve your home without having any issues from the councils or regulations. Before your planned loft conversion can be covered under Permitted Development, there are some certain criteria that must be met. This criteria includes the following:

✓ The extension must not go beyond the existing slope of the roof at the front of the house.

✓ The loft space converted must not go beyond 40 cubic metres in a terraced house.

✓ The roof’s height must not be increased by the extension.

✓ The loft space converted must not reach beyond 50 cubic metres in a detached or semi detached house.

✓ The plan for the extension mustn’t involve structures like balconies, verandas or anything other structures of this nature.

✓ The roof extension should be positioned as far back as possible or at least 20cm from the existing eaves.

✓ The side that faces the window openings should be at least 1.7m beyond the floor and the windows should also be obscured.

✓ The roof extension must not overhang the existing roof or wall of the house.

✓ The materials that are to be used must be similar or the same to the materials that has already been used on the house’s exterior.

However, you should bear in mind that there are some properties that are exempt from Permitted Development. Examples of these type of properties include conservation areas, Areas Of Outstanding Natural Beauty and World Heritage sites. Permitted Development does not also provide coverage for listed buildings.

There are two main types of cladding. The first is material cladding, which refers to layers of a material that are attached to the external walls. The material used could be timber, PVC, stone, or other materials. The second type of cladding is rendering, where a coat of plaster is applied to the wall.

Do you want your house to be built using brick? Or perhaps you just require the professional services of a bricklayer. Regardless of your bricklaying needs, the cost charged depends on each job as every job is unique. Bricklayers generally look at each task individually and charges based on the complexity of each. We’ve put together this guide to give you an idea of the costs charged by bricklayers. Let’s have a look!

Generally, bricklayers charge either based on a daily rate or a fixed price for a particular amount of bricks ( usually a thousand bricks or 10 - 12 metres square). On the average, an experienced bricklayer can charge within a range of £150 to £200 daily rate and if a labour is needed for the job, an additional £60 to £100 may be included to get the job completed in a quick and fast manner. If the quoting is done based on the number of bricks to be incorporated, then a thousand bricks will be quoted in between £350 to £450 which should be completed in a couple of days.

You should however take note that most times, the bricklayer’s cost will depend on the amount of work involved in the project. As a result, a more tedious and challenging project will most definitely cost more than a simpler one. Examples of some difficult projects that’s likely to cost more are hard to reach areas, difficult sites as well as second storeys which are considered to be more challenging than single storey buildings. What’s more? The complexity of the project is also a great cost factor. While some projects are basically direct and straightforward, others involve curves and more complex designs which will ultimately make the cost jump up.

Aside from the cold weather not being the most pleasant condition to work in, the winter weather can also cause a lot of problems for construction workers and even more so when you’re working with render. Poor weather conditions can generally cause a lot of harms on the final finish of a render. Below are some of the reasons why you should not consider rendering in a bad weather.

✓ Lime bloom. Render can be impacted by lime bloom as they are subjected to damp conditions and low temperatures while curing. This is due to the fact that cement are intolerant to slower drying conditions especially immediately affect its application.

✓ Top coats can be compromised. Coating are likely to get washed off before they’re even afforded the chance to set if drying conditions are low.

However, because its cold out there doesn’t necessarily imply that work must stop. It’s very possible to render during the winter months but to avoid potential pitfalls, we’ve got some tip that can be of great help. Let’s have a look!

✓ Check the weather forecast. Determine the drying and curing time and watch the forecast for the temperature dropping at night.

✓ Select the most suitable render. There are renders that are suitable for application in low temperatures to about 5℃ or even as low as 1℃. These types of render are fast setting which makes them perfect for the cold condition.

✓ Watch out for frost. Frost and render are enemies. Therefore, it won’t be wise to work with frosted materials, on frosted subtrates or apply below the recommended temperature that’s written on the product’s datasheet.

✓ Protect the finish. Make use of artificial enclosures around the scaffolding to battle adverse weather conditions.