Find a Builder you can trust in Shropshire.

How To Plasterboard A Wall

If you’re looking to plasterboard your wall, one of the essential things to have in mind is that the plasterboard must be hung horizontally and not vertically. Due to the way they’re manufactured, plasterboard sheets normally possess a “grain along the length. This implies that, it’s only when they’re firmly placed perpendicular against the wall that they’re able to achieve their maximum strength. Materials you’ll need to complete this task includes: Tape measure, stanley knife, pencil, spirit level, drill driver or screw gun, surform, drywall screws and handsaw. Now let’s have a look at the wall plasterboarding steps!

• To plasterboard a wall the first step to take is to place each board in such a way to make the edges the centre of the noggins and upright. Also, the the adjoining walls and door openings should fit closely to the edges.

• Work from the door opening to the ending wall. From the the stud’s edge to the noggin’s centre, use your tape measure to measure a cut board and as a rule to mark up.

• Place your spirit level on the marks and use the Stanley knife to run a line along the intended cut. Once done, turn the board on its edge and give a sharp push on the back to split.

• Cut the paper left with the knife after folding the split edge back on itself. This way, you should get a nice and clean edge.

• In its right position, place the board up against the studwork. Install the screws on the board’s edges where a noggin or upright can be seen.

• Mark lines down across the board at the stud’s centre.

• Cut the end boards to length.

• Install the remaining boards as mentioned above. While doing this, make sure the factory edges are together.

• Cut any board extending into an opening and finish the edges using a surform.

We’d recommend you hire the professional services of a plasterer for the best results especially if you lack the necessary training or experience. Plasterboarding a wall can be a tricky challenge and you’d save yourself some time, money and effort by getting it right on the first trial.

Typically, loft conversions do not require planning permission except in certain situations. They’re usually covered under what’s known as Permitted Development. Certain building works like loft conversion, rear extension and conservatories are granted planning permission by local authorities. Permitted Development, however, gives you a free range to improve your home without having any issues from the councils or regulations. Before your planned loft conversion can be covered under Permitted Development, there are some certain criteria that must be met. This criteria includes the following:

✓ The extension must not go beyond the existing slope of the roof at the front of the house.

✓ The loft space converted must not go beyond 40 cubic metres in a terraced house.

✓ The roof’s height must not be increased by the extension.

✓ The loft space converted must not reach beyond 50 cubic metres in a detached or semi detached house.

✓ The plan for the extension mustn’t involve structures like balconies, verandas or anything other structures of this nature.

✓ The roof extension should be positioned as far back as possible or at least 20cm from the existing eaves.

✓ The side that faces the window openings should be at least 1.7m beyond the floor and the windows should also be obscured.

✓ The roof extension must not overhang the existing roof or wall of the house.

✓ The materials that are to be used must be similar or the same to the materials that has already been used on the house’s exterior.

However, you should bear in mind that there are some properties that are exempt from Permitted Development. Examples of these type of properties include conservation areas, Areas Of Outstanding Natural Beauty and World Heritage sites. Permitted Development does not also provide coverage for listed buildings.

Sand is a very important element in bricklaying as far as a mortar mix is concerned. Generally, the quality of the sand is the major factor determining the quality of a plaster mix or mortar mix. It’s recommended that the sand should have enough ‘fines’ (- 75 micron material) to get a good plastic mix with a water content that’s less than 350 litres/m3. Generally, a mortar mix or plaster mix is made within the range of one bag of cement to 200 to 300 litres of damp sand.

Apart from experience the next best indicator of the quality of sand is a field test. In other words, if you do not have the required training or experience in bricklaying, the best bet to determine the amount of sand for a good quality mix is by carrying out a field test. Let’s have a look!

• Get about 50kg of sand and air dry it.

• Scoop 25kg of the sand, 5 kg of cement as well as litres of water ( with 1 litre and 1.5 litres of the water in different containers).

• Mix the cement and sand to form a smooth, uniform and consistent colour.

• One after the other, mix the the sand - cement mixture in the three quantities of water. Do this until you’re able to achieve a mix that’s workable enough to use as plaster.

With that done, you should take note that if 5 litres of water is sufficient then the quality and quantity of the sand is perfect. If you’d require 6 litres of water to get a mix workable as a plaster, then both the quality and quantity of the sand is average. However, if you’d need 7 litres of water to get a mix workable as a plaster, then the quality of the sand is poor. Any requirement of water above 7 litres implies a very poor quality of sand.

If you want to install an external wall, it is only wise to consider whether or not a planning permission is required in order to avoid a hefty fine. In a great kudos to the government and a welcome relief to home and property owners, the installation of external wall insulation is seen as an “improvement to the house and not an “extension or an “enlargement. Ultimately, this implies that external wall insulation fitting is to be done under permitted development and a planning application may not be required. However, like many other regulations, there are also exceptions to this rule and the main one is if the activity changes the appearance of your property. Properties such as a listed building having tighter regulations may pose some issues. As a result, we’d advise you to consult your local authority to ensure that there’s no fast rule to this topic before commencement of the external wall insulation project.

At the moment, according to the Government Building Regulations, the surface of the entire wall is to be improved to existing standards if the area to be insulated exceeds 25 percent of the wall. In normal situations this is usually the typical case, however to prevent avoidable fines and other possible punishments, it is always best to reach to your local authority and check out the rules guiding external wall insulation in your constituency. Furthermore, since external wall insulation is not a task that’s recommended to be done by yourself, you can also ask the professional external wall insulation fitting company for the applying rules before proceeding. As a good professional, the company should have a better knowledge of the rules and regulation guiding its activities.

There is a variety of methods available to ensure that your paving drains properly, for example draining into a lawn or soakaway. Correct drainage of paving is a requirement for planning permission. See our guide on planning permission for paving for more information.

Aside from the cold weather not being the most pleasant condition to work in, the winter weather can also cause a lot of problems for construction workers and even more so when you’re working with render. Poor weather conditions can generally cause a lot of harms on the final finish of a render. Below are some of the reasons why you should not consider rendering in a bad weather.

✓ Lime bloom. Render can be impacted by lime bloom as they are subjected to damp conditions and low temperatures while curing. This is due to the fact that cement are intolerant to slower drying conditions especially immediately affect its application.

✓ Top coats can be compromised. Coating are likely to get washed off before they’re even afforded the chance to set if drying conditions are low.

However, because its cold out there doesn’t necessarily imply that work must stop. It’s very possible to render during the winter months but to avoid potential pitfalls, we’ve got some tip that can be of great help. Let’s have a look!

✓ Check the weather forecast. Determine the drying and curing time and watch the forecast for the temperature dropping at night.

✓ Select the most suitable render. There are renders that are suitable for application in low temperatures to about 5℃ or even as low as 1℃. These types of render are fast setting which makes them perfect for the cold condition.

✓ Watch out for frost. Frost and render are enemies. Therefore, it won’t be wise to work with frosted materials, on frosted subtrates or apply below the recommended temperature that’s written on the product’s datasheet.

✓ Protect the finish. Make use of artificial enclosures around the scaffolding to battle adverse weather conditions.

Getting the opportunity to fit your very own bespoke wardrobe in your home is a really exciting prospect. However, when planning to install customizable fitted wardrobe, one factor that turns off most home and property owners is the belief that the bespoke solution is actually a very expensive one. But the fact, in reality, is that so far you’re prepared for any associated costs bespoke fitted wardrobes should not make you break the bank to get one done in your home. So if you’re planning to install this type of fitted wardrobe and wondering about the cost, you’ve come to the right place! In this article, we’ve put together the price range estimate as well as the potential extra costs to help you plan ahead and get your dream wardrobe without having to worry too much about unpleasant surprises along the way. Let’s take a look!

With some companies you’ll be provided with a fixed price which can’t be negotiated. While prices from other suppliers will usually start within the range of £1400 to about £1700 for the standard wood finish wardrobe, but this can also reach about £5000 or more for high end or premium finishes, without taking the cost of the added extras into consideration. Ultimately, this often implies having to pay out more money for interiors and additional features than you’re likely going to need. Below is a rough guide to the cost of fitted wardrobes from Spaceslide:

✓ The price for a 2, 3 or 4 door sliding wardrobe starts at £452.37.

✓ The price for a 3 door fitted wardrobe starts at £659.07

✓ The price for a 4 door fitted fitted wardrobe starts at £865.77.

Additional costs you’ll have to consider before getting started includes the cost of hiring installers as well as delivery and removal cost.

The short and simple answer is yes, fitted wardrobes add value to any home or property. Owning a home is mostly the single most expensive asset that a person can possess. And as a result, your home is a very special asset that you’d want to make conducive and maintain to the best of your ability. To retain the value of your home or even add to it, you have to learn how to maximize its potentials using different means. In the UK, a big issue for most households is usually the lack of storage space and most especially, the quickly shaped bedrooms which is really affected with storage problems. It almost always seems like there isn’t enough space to keep our clothes as well as the never-ending portfolio of accessories, devices and gadgets. Therefore, an extra or excess usable room inside a home is always a premium.

In other words maximizing the space you have, especially the unused ones, is a great way to add value to your property. Custom made fitted wardrobes are a great means to making the most out of the space within your home and are also designed to last for several years. Unlike the freestanding wardrobes, modern and fitted wardrobes are not only visually appealing, but they’re also customizable to fully maximize every inch of space within the room. As a result, they’re the ideal solution especially for loft rooms where the bedroom may be slope or oddly shaped to make the best out of the space available.

Potential investors are always eager to invest in homes with enough space that are well maximized. Therefore, a fitted wardrobe will not only help you create a better demand for your home at the point of selling, but it’ll also go a long to increase its value in so many ways.