Find a Builder you can trust in Williton.

Driveways usually sink because they haven’t been laid properly. They may not have been dug deep enough, or the installer might not have used the right materials. This will need to be corrected at the earliest opportunity, although in extreme cases, the driveway may need to be completly be relaid.

The main reason that people use cladding or rendering on their property is the aesthetic benefit. These materials can really boost the appearance of a home. Cladding and rendering can also increase the thermal performance of a property. Speak to a specialist to find out whether your property will benefit.

Pebble dash is an effective way to tune up your house or property as it can go a long way to enhance its curb appeal while also add to its resale value if you should decide to sell later on. Although, it’s highly recommended to leave this task for a reputable specialist, it’s also something that can be done as a DIY task. It must be states that this is a pretty difficult job and even more so if you haven’t attempted it before. In this post we’re going to take you through the processes involved in pebble dashing a wall. Let’s take a look!

• Mix up water with the lime strictly following the manufacturer’s instructions. Once done, leave it covered up to hydrate for at least 24 hours.
• Take one part of the slaked lime and mix it up with cement and six parts sand. This is to give the base mixture required to spread onto the surface.
• Use a trowel to apply the mixture onto the wall. Ensure that the trowel is level and use the edges to make a flat and smooth layer of the mixture on the surface as a base layer. Allow the base layer to dry for up to an hour. Then, rake the surface using a notched trowel and allow to dry for a minimum of 24 hours.
• Rinse and drain your pebbles. Then, set them under the wall you’re pebble dashing.
• Take the top coat of five parts sand and mix with one part cement and one part slaked lime. Use a trowel to apply this mixture over the base layer and smoothen it with the trowel to create a flat and even top layer.
• Spread a plastic sheet beneath the wall you’re pebble dashing to capture any loose pebbles as they fall.
• Grab the bucket of pebbles below the wall and scoop some of the pebbles up using a scoop or trowel. Some will stick and some will fall into the plastic sheet already placed below. Continue throwing the pebble dash until the surface is completely and evenly covered with pebbles.
• Lightly press and fit the pebbles on each section into the wall and leave for at least 24 hours to dry.

Well the reality is, sometimes, neighbours just don’t get along. With several individuals living in close proximity, it’s little surprise they tend to get on one another’s nerves from time to time. However, there’s a difference between having a tiff and being able to transform your house the way you want without having to obtain your neighbour’s approval.

The short and simple answer to this question is, not necessarily. However, you must first educate yourself by thinking about your extension and how it affects the houses around you. We’d strongly recommend you talk proposals through with your neighbour so as to avoid possible conflicts later. There are a number of reasons why your neighbour can protest to your new home extension plans. Let’s take a look!

• In the event whereby your new extension is blocking their view or providing an unwanted shade on their property. Here, they have a legitimate reason to protest as no one would want their once sunny garden suddenly covered or plummet into shade.
• In the event where it leads to a loss of privacy. For instance, if your new extension possesses a window which overlooks the neighbour’s property in any way. This is likely to be taken as an invasion of privacy and that has a little to no chance of being a welcomed idea.
• If it’s a major project and going to take a lot of weeks before completion. The noise generated, especially when your neighbours are enjoying your summer holidays or weekends, can make their gardens not as relaxing as it used to be.

When it comes to laying of bricks, it is essential to get the right mortar mix. It is vital, be it for construction or maintenance projects, so far mortar is required. There are several materials incorporated in getting mortar which includes both cement and sharp sand, soft sand or plasterer’s sand and lots more. Here, we are going to look at the right ratio for cement and sand mix in bricklaying.

Cement include ingredients such as iron, aluminium, as well as silicon and it is mainly used for mortars like aerated cement mortar, Portland cement mortar and gauged mortar. Sand, on the other hand, comes in different forms such as sharp sand, soft sand and plasterer’s sand. The sharp sand consists of a larger grain size than the others and is usually incorporated in the construction areas that requires more strength as well as flexibility. Soft sand is the most common one used in mortar and it’s also referred to as bricklayers’ sand. These are used to make all types of mortar. Finally the plasterer’s sand which neither has the sharp sand’s coarseness nor the fineness of the soft sand, but can also be used for any form of mortar.

Cement and sand mortar is used for a plethora of bricklaying jobs serving as a glue for bricks, walls and pillars, while also repairing or maintaining old listed buildings. The preferred ratio here is 1:3 to 1:5 of cement and building sand. Meanwhile, to get a sand cement mix, essential materials that are required includes water, soft building sand as well as cement. However, you must also note that a sand and cement mortar is not used for structural projects, rather a concrete ratio is used.

If you’re considering converting a barn or buying one, you shouldn’t need to worry about it being cold. This is because building regulations dictate that when you convert a barn, you need to insulate it to meet specific standards. However, it’s worth considering its heating system and ceiling heights carefully – some barn conversions are likely to take longer and be more expensive to heat up than others.

There are two main types of cladding. The first is material cladding, which refers to layers of a material that are attached to the external walls. The material used could be timber, PVC, stone, or other materials. The second type of cladding is rendering, where a coat of plaster is applied to the wall.

How long it takes to install insulation will depend on the size of your property. In general, loft and cavity wall insulation can be installed in a day or two. External wall insulation will usually take longer to install. The rep or installer will be able to advise you when quoting for the job how long this will be.