Find a Builder you can trust in Warwickshire.

If you’re planning to construct a kitchen extension on your property, one of the first things that comes to mind is whether or not you’ll require a planning permission before you proceed. Generally, kitchen extensions are normally classified as permitted development which allows you to carry out your project without any interruptions from the law or your local authority. In other words, if your extension is meets up with the guidelines of the permitted development rights, you won’t have to apply for a planning permission. However if otherwise, you’ll have to apply for a planning permission to your local council and may require additional reports. And regardless of your position, you’ll always need building regulations approval before you can carry out any kitchen extension project. It may also be required that you’ll have to issue a part wall notice if you’re to build on or close to the boundary with a neighbour.

If you don’t want to go through the hassle and stress involved in applying for a planning permission with your local council, then you must ensure the following:

✓ Your kitchen extension must not be over half of the area of land around your main house.

✓ The kitchen extension must not be side elevation onto a highway or forward of the principal elevation.

✓ The extension must not be taller than the highest part of the roof.

✓ The height of your kitchen extension must not go beyond four metres.

✓ Kitchen extension that’s more than one storey must not go exceed the rear wall of the main house by more than three metres.

✓ Two storey kitchen extensions must not be closer to rear boundary by anything less than seven metres.

✓ The kitchen extension must not include balconies, verandas or any raised platforms.

Insulating a cavity wall should not affect the damp proofing of the wall. All insulation approved for use in cavity walls has been tested to ensure that it does not allow damp to pass through the wall. Some walls which receive a lot of wind driven rain are unsuitable for cavity wall insulation.

How To Plasterboard A Wall

If you’re looking to plasterboard your wall, one of the essential things to have in mind is that the plasterboard must be hung horizontally and not vertically. Due to the way they’re manufactured, plasterboard sheets normally possess a “grain along the length. This implies that, it’s only when they’re firmly placed perpendicular against the wall that they’re able to achieve their maximum strength. Materials you’ll need to complete this task includes: Tape measure, stanley knife, pencil, spirit level, drill driver or screw gun, surform, drywall screws and handsaw. Now let’s have a look at the wall plasterboarding steps!

• To plasterboard a wall the first step to take is to place each board in such a way to make the edges the centre of the noggins and upright. Also, the the adjoining walls and door openings should fit closely to the edges.

• Work from the door opening to the ending wall. From the the stud’s edge to the noggin’s centre, use your tape measure to measure a cut board and as a rule to mark up.

• Place your spirit level on the marks and use the Stanley knife to run a line along the intended cut. Once done, turn the board on its edge and give a sharp push on the back to split.

• Cut the paper left with the knife after folding the split edge back on itself. This way, you should get a nice and clean edge.

• In its right position, place the board up against the studwork. Install the screws on the board’s edges where a noggin or upright can be seen.

• Mark lines down across the board at the stud’s centre.

• Cut the end boards to length.

• Install the remaining boards as mentioned above. While doing this, make sure the factory edges are together.

• Cut any board extending into an opening and finish the edges using a surform.

We’d recommend you hire the professional services of a plasterer for the best results especially if you lack the necessary training or experience. Plasterboarding a wall can be a tricky challenge and you’d save yourself some time, money and effort by getting it right on the first trial.

Over the years there has been an increase in the recommended thickness of loft insulation by the government. Obviously, the reason behind this is pretty simply - the thicker the layer of your loft insulation the bigger your savings. The UK government is very keen to every house in the country to have loft insulation fitted where possible as it helps to minimize the heating demands of these properties. Households get to benefit from loft insulation in so many ways which includes reduced energy energy bills as well as having a home that stays at a more comfortable temperature for longer.

Generally, for the government energy efficiency is crucial as it implies that the highest demand ( which is usually the time of the day when gas or electricity use is at its peak ) reduces, since each building requires slightly less energy. Overall, that ultimately implies that new power plants don’t have to be built which is some nice cost savings for the government.

In the 1980’s, any thickness of loft insulation from 25 mm to 50 mm was considered the standard. But then, building regulations stated that homes should have as much as 100 mm of loft insulation. Over time, this gradually increased to 270mm for new builds and also recommended for other properties, although not essential. As a result of this, there’s always a need to check how much insulation you currently have in your loft before you decide to purchase more. You may discover that you already have something within the range of 20 mm to 200 mm up there and knowing this and the insulation values will assist in determining how much more you’ll need to purchase, if any at all. You should also note that some modern materials can offer the same thermal insulation whilst not being as thick.

Finding a builder nearby can have enormous assistance when it comes to your build. Period on site, their familiarity of local planning permission, constructors’ dealers and other local trades are all vital bits of knowledge that you’ll welcome on site.

It is always wise to walk around in your local area or drive to a site where any construction work is going on. It’ll give you a proper impression of the constructors who are active nearby. You don’t have to like their style of work or the project they are currently carrying out – after all, a builder can only produce what’s on the plans in front of them.

Find a Builder Other Tradesmen Recommend

If you’ve had to call an electrician before or a local plumber and liked their work, you can always ask them if they have any builders whom they would recommend. Maximum tradesmen get used to seeing the similar acquainted names from one place to another in the sites they are working on and every so often has favourites for who they like to work with — and who they see as a good source of work.

Always Talk to Previous Customers

Once you’ve found a builder you would like to work with, ask them for a list of previous customers they have worked with; they ought to be glad to offer particulars if they’re self-assured they’ve done an effective job.

Look for a builder online

A decent place to start looking for builders online is on sites like the Federation of Master Builders. They have a search tool where you can find precise crafts in your area and look at their situations. All FMB members are assessed and individualistically examined and are checked to ensure that they have the correct insurances in place.

Are you about to start a new construction job when it’s a heavily rainy period? Or perhaps you’re just interested in knowing how bricklayers work. Well regardless of your purpose, one thing you should know is laying of bricks has a few rules and one of them is not to lay a brick wall when its raining. This is mainly because your structure’s quality and integrity would be heavily compromised if water comes in contact with the mortar before it gets the time to dry. However, with the help of a concrete protective tent, you can prevent water from coming in contact and damaging the mortar. So let’s look at the procedures to follow to work in the rain!

lDetermine The Concrete Protective Tents Required

• Concrete protective tents come in various sizes so you have to know what’s required to get the job done.

• Firstly, calculate the amount of space required to lay the brick wall

• Then, incorporate the appropriate size and number of tents.

lSet Up The Tents

• Follow the manufacturer’s instruction to set up the tents

• Once installed, the tent should extend past the location for the bricklaying and slope downwards.

l Access The Area

• Inspect the location during rainfall to ensure water is not sneaking through.

lBuild a Lumber Frame

• Use 2 to 4 pieces of lumber to build a frame.

• Set it into the ground depending on the size of your wall

lApply Concrete or Mortar

• Fill up the frame with either concrete or mortar.

• Follow the manufacturer’s instruction to allow the mixture to cure.

lPrepare the Brick Wall’s Mortar

• Mix the mortar for the brick wall construction

• Follow the manufacturer’s instruction for the process.

When you’re done laying the bricks, you can remove the protective tents once you’re certain the rain has stopped. Exposure to sun and air will speed up the curing process, which is quite important to protect the integrity of your structure.

When it comes to extending a home, the rear of the house often comes to mind a lot more than the front. However, this doesn’t mean that you can’t extend the front of your house. This can be done either as part of a renovation project whereby the entire house is incorporated or it can also be done in isolation. It’s possible to extend the front of your house without the need to apply for a planning permission, however, there are a bunch of limitations you’d have to comply with if you wish to carry out with such a project. Sometimes, this may imply that extending to the front of your home is more tedious and tasking than extending your home’s rear. So exactly how far can you extend the front of your home without planning permission?

The short and simple answer to this question is 2 metres square area with a height not more than 3 metres. Generally, you do not need a planning permission to build a front porch as long as its area doesn’t go beyond 2 square metres from a public road or walkway. Also, a tiled or slated roof can be as much as 4 metres but other roofs must not go beyond 3 metres in height. If you want to extend the front of your home beyond the restrictions specified, then you’ll have to apply for a planning permission.

Extending the front of home can be quite costly, but this can be controlled by not building to the extension to the highest specification, not including an extension on kitchens or bathrooms and more.

General construction work should be restricted to the following hours: Monday to Friday 8am to 6pm. Saturdays 8am to 1pm. Most councils advice that noisy work is prohibited on Sundays and bank holidays but you should check with your local council to confirm this.