Find a Builder you can trust in Wolverhampton.

How To Plasterboard A Wall

If you’re looking to plasterboard your wall, one of the essential things to have in mind is that the plasterboard must be hung horizontally and not vertically. Due to the way they’re manufactured, plasterboard sheets normally possess a “grain along the length. This implies that, it’s only when they’re firmly placed perpendicular against the wall that they’re able to achieve their maximum strength. Materials you’ll need to complete this task includes: Tape measure, stanley knife, pencil, spirit level, drill driver or screw gun, surform, drywall screws and handsaw. Now let’s have a look at the wall plasterboarding steps!

• To plasterboard a wall the first step to take is to place each board in such a way to make the edges the centre of the noggins and upright. Also, the the adjoining walls and door openings should fit closely to the edges.

• Work from the door opening to the ending wall. From the the stud’s edge to the noggin’s centre, use your tape measure to measure a cut board and as a rule to mark up.

• Place your spirit level on the marks and use the Stanley knife to run a line along the intended cut. Once done, turn the board on its edge and give a sharp push on the back to split.

• Cut the paper left with the knife after folding the split edge back on itself. This way, you should get a nice and clean edge.

• In its right position, place the board up against the studwork. Install the screws on the board’s edges where a noggin or upright can be seen.

• Mark lines down across the board at the stud’s centre.

• Cut the end boards to length.

• Install the remaining boards as mentioned above. While doing this, make sure the factory edges are together.

• Cut any board extending into an opening and finish the edges using a surform.

We’d recommend you hire the professional services of a plasterer for the best results especially if you lack the necessary training or experience. Plasterboarding a wall can be a tricky challenge and you’d save yourself some time, money and effort by getting it right on the first trial.

Yes. Most extensions will add substantial value to your home, and you may find that the extension adds more value than it cost. However, it’s important to be sure that the home remains balanced. Extending your garage and leaving your property with no parking spaces, for example, may impact your ability to sell.

Windows or lightwells can be a great way to introduce natural light into your basement, making it a more valuable, enjoyable space. However, they’re not always an essential requirement.

It’s important for your basement conversion to meet ventilation and fire safety building regulations. Windows can be a good way to do this, but they’re not the only option. Stack or mechanical ventilation, or ensuring that stairs up from your basement connect to an exit can be a good alternative.

So, while windows can be a great asset to your basement conversion, if you can’t afford them or they’re not structurally feasible, you can still create a basement conversion without them.

Damp issues on a property are usually generated by a lot of factors such as a poor or broken guttering, condensation and lots more. The question arising here is what is the possibility of External Wall Insulation (EWI) preventing condensation? Not only is EWI a reliable way to reduce condensation-caused damp, but it’s also one of the major reasons property owners in solid wall homes consider thermally rendering or cladding their external walls.

Condensation arises as a result of warm moist internal air hitting a cold surface such as the steaming up of both windows and mirror when having a shower. What happens here is the condensation of the water vapour in the air from a gas to liquid in the process of touching the cold surface - one whose temperature is significantly reduced to reach the dew point. At the dew point, condensation is very rampant, and to tackle this issue you’ll have to heighten the wall temperature in order to convert the moisture to vapour and permit it to pass through the wall. And that’s exactly the job of an external wall insulation!

To get started you must ensure that the walls are clean and dry prior to fitting the external wall insulation. The month of May through to September when the weather tends to be dry and more stable are usually the best period to carry out the project. The external wall insulation will function just like a cosy blanket around the building. Ultimately, changing the feel and temperature of the inside of your home. As a result, the previously cold walls will no longer be cold which goes a long way to mitigate the effects of condensation. Furthermore, when an EWI is installed, the rooms of your home will automatically trap more thermal mass as the heat is saved in the walls’ fabric and released back when the temperature drops.

Over the years, garden rooms have gradually become a popular choice amongst homeowners as a cost effective way of expanding living space within a home or property. A garden room is basically a living space and a type of pavilion building made from wood that’s well insulated, double glazed as well as electrically wired. It’s however a building which is subsidiary to the main one, built with the purpose of creating an extra functional space within the property. These garden outbuildings are very functional and can be used as a garden studio, office, salon and much more. They can also be incorporated for recreational purposes for evening relaxations, family and friends get-together, lounge or even spa. Other possible uses of a garden room include gyms, pool houses, playrooms, dens, home cinemas and game rooms.

Garden rooms are functional living spaces that are usable throughout the year. And with the rate at which their popularity is growing, you’ll find some companies offering cheap and low quality alternatives featuring shed like construction and felt roof. Garden rooms, on the other hand, are a valuable investment with superior designs and top notch build. They’re constructed in a very similar way to houses with timber frames. Furthermore, they are fully insulated and can also include the normal building solutions such as heating and running water, electricity and many more depending on the requirements of the home or property owner. With the durability of garden rooms being a major objective, they’re typically clad in natural solid timber like Cedar, Larch or Acacia. Materials such as EPDM rubber or cedar shingles are normally used for the roof covering. What’s more? They usually have large expanses of glazing and glazed doors fitted.

Cement is a crucial element in bricklaying that’s widely used in both construction as well as finishing works. Generally, they’re used to aerate concrete blocks, connect bricks, prepare plaster, floor levelling as well as the making of precast products. The major reason cement is one of the most common construction materials as its incredible ability to hold structure together. To get a cement plaster, you’d simply have to mix cement with both water and sand. However, when you mix cement with lime, sand and water, you’ll get a mortar.

For cements mortars to be used inside joints, you’ll have to include 1 part cement at the minimum to not more than 2 parts sand by weight which should be dry mixed and moistened with enough water to allow for troweling and packing without falling apart. Generally, the cement sand ratio in a mortar is in between 1:2 to 1:6. The cement and sand mix ratio is largely based on the importance of the project.

Cement provides a plethora of uses in bricklaying and these includes:

• Preparation of cement concrete

• Preparation of cement mortar

• Building fireproof and thermal proof structures

• Building chemical proof structures

• Serving as a grout material

• Building hydrographic and frost resistant structures

• Manufacturing precast members

• Constructing aesthetic concrete

• Constructing cement concrete roads

There are several types of cements with each having its specific purpose. For instance, the type of cement more suited to building a fire proof structure is a high alumnia cement and to build a hydrographic structure, cements like expanding cement, hydrophobic cement, pozzolana cement and quick setting cement are the best bet. Acid resistant cements are more useful in building chemical proof structures, portland cements are best suited to making grout materials, while coloured cements are preferable to building aesthetic structures.

Are you looking to create some more space in your home with your garage being almost dispensable? If yes, then considering a garage conversion project may be the way to go. Unlike many other extension options, garage conversion does not take up an additional space as it only changes the current structure of the garage. As a result, the cost of completing a garage conversion project can be relatively attractive when compared to other space creating alternatives. So exactly how much would a garage conversion project cost? Well, there’s no precise answer for this as several influencing factors come to play. However, in this guide we’ll give you a rough idea of the average costs that you’re likely going to encounter. Some of the factors that can influence your budget dramatically includes the following:

• The size of the conversion. The larger the size of the garage per square feet, the more cost you’ll have to expend.

• The type of your property - listed buildings are usually more expensive.

• Your location in the UK. If you stay in London where there’s a higher demand, you’ll most likely pay more.

• You’re likely to pay more if a specialist knowledge is required.

• The amount of glazing to be installed

• Quality of the materials to be incorporated.

• Quality of the professional to carry out the installation service.

On average, when it comes to garage conversion projects, you’re likely to pay the following depending on the per square metre given:

• A single garage of about 15 square metre will cost within the range of £6,000 to £15,000.

• A double garage of about 30 square metre will cost within the range of £12,000 to £30,000.

Fitted wardrobes are the best choice of wardrobe for most households and they’re a popular option for several homeowners for a good reason. Not only are they able to efficiently maximize your space and fit into any space no matter how awkward, but they can also be customized to fit your personal needs to feature custom lighting and many more. So if you’re planning to have one fitted but on a tight budget, you’d probably be wondering how you can install a fitted wardrobe in an alcove by yourself. This is a relatively easy task if you’re attentive to the details, however, if you’re not confident enough to pull this off, we’d advise that you get in touch with a professional who can guarantee the best results for help.

To construct a fitted wardrobe in an alcove, simply follow these steps:

✓ Take a measurement of the available space including the length, breadth and width.

✓ Sketch out what you want the wardrobe to look like while also staying within the measurements. Here, you’ll have to be particular about everything like the drawers, shelves etc.

✓ Build the frames upon which every other construction would be made.

✓ Attach the frames to the wall and floor. Make use of a hammer drill with a masonry bit to drill the holes if its a concrete floor.

✓ At this stage, you’ll have to start building your shelves in accordance to the number you’ll need.

✓ Based on the design in step 2 above, you’ll have to add the door at this stage. This is however optional as some homeowners prefer door-less wardrobes.

✓ The final step is to paint the the finished wardrobe to your taste with your choice of colour.