Find a Conservatory Installer you can trust in Seascale.

Do You Need A Building Reg For A Conservatory?

If you’re planning to build a conservatory in your home, it’s only logical to consider whether or not you require a building reg for such a structure. Generally, several conservatories, summer buildings, sheds as well as outbuildings do not require building regulation approval to erect. One of the applicable rules is the fact that if they’re ( small or less than 30m2) or constructed with non combustible material, or are differentiated from structures nearby or land and don’t feature sleeping accommodation or room, then they’re not required to submit a building regulations approval application. However, it’s strongly recommended to check with your local authority before you commence the project as only they can provide the most accurate information.

Generally, conservatories should be primarily built of translucent walls and roofs, while also possessing an external type door separating them from the main building within a property. What’s more? The foundations and floors, however, can be laid in a number of ways, but you’ll have to put into consideration the conditions of the ground, trees as well as the existing drains. It’s also a wise decision to include insulation which makes the structure a lot easier to heat especially during the cold months.

Overall, conservatories are usually exempt from building regulations if the following conditions are met:

✓ If the conservatory is erected at ground level and are not up to 30 square metres in floor area.

✓ If the structure is separated from the rest of the house with an external quality walls, windows or doors

✓ If the conservatory features an independent heating system with different temperature as well as on/off controls

✓ If the glazing and electrical installations are in total compliancewith the relevant regulatory requirements.

This varies according to the quality of the conservatory and installation work. If these are both high quality, your conservatory should last at least 25 years. But obviously if you notice deterioration or leaks, then this could be an early warning sign that time is running out.

• The rules only apply to houses – flats and maisonettes are not included
• Only 50% of the area of land around the original house can be covered by extensions, including conservatories, and other buildings
• You mustn’t build the conservatory higher than the highest part of the original roof
• Where the wooden conservatory comes within 2 metres of the boundary, the height at the eaves can’t exceed 3 metres
• A rear wooden conservatory can’t extend beyond the rear wall of the original house by more than 4 metres if it’s a detached house, or more than 3 metres for any other type of house
• For side extensions, for example a lean-to wooden conservatory, it can’t exceed 4 metres in height and can only be up to half the width of the original house

A good way to get rid of your conservatory is to sell it. Depending on its condition you may not make much money from it, but it’s an easy and financially viable way to get your old conservatory dismantled and out of the way. If you are replacing it, the installer can easily remove this for you completely.

You might think that all wooden conservatories are the same. But there are actually lots of differences between them, and some conservatories are better than others. One of the most important factors to consider when you’re looking for a wooden conservatory is the type of wood that it’s made from. Generally, there are two different types to look out for: softwood and hardwood. So what wood should be used for a wooden conservatory?

Softwood conservatories are usually made from European redwood or Siberian larch. These types of conservatories are the cheapest wooden conservatories you can buy because the wood grows much faster than hardwoods. However, due to their soft nature, they may only last 7-15 years, reducing their cost-effectivity.

The best wood to use for a wooden conservatory is a hardwood. The most expensive type is oak, but you get what you pay for – it looks fabulous and it can also be coated with a bug and pest-resistant solution to increase its longevity. If you haven’t got the budget for oak, other hardwood options include Brazilian cedar, idigbo and luan, which are still great choices. Make sure you speak to your conservatory installer about the ‘closeness’ of the wood grains, as close-grained hardwoods are said to be the most suitable for conservatories. You should also check that your supplier has strict control of the quality of the wood so can ensure that it’s been well seasoned and prepared for use in construction.

Generally, if you want to do a job, you can as well ensure that’s done properly. You may be considering building a small base for an orangery, but no matter how small it is, it just shouldn’t be done to any other than a compliant standard, and that’s whether or not an approval is needed. When it comes to building work which is covered by Building Regulations, you are required to comply (by the law) with the regulations and to make use of one of the two types of Building Control Service available. These includes the Building Control Service given by your local authority or the Building Control Service given by approved inspectors.

Regardless of the service you opt for, you’re going to pay but the preferred service may offer an advice before commencement of the project. The individual carrying out the building work is charged with the responsibility of ensuring total compliance with the regulations. Therefore, if you select to undertake the project by yourself, the responsibility is primarily on you. In the same vein, if you opt for a building company the responsibility would be the company’s, but you should always ensure to confirm this position before commencement of the project. You must also take note that you may be served with an enforcement notice if you fail to comply with the regulations as the owner of the building. So it’s advisable that you choose your builder very carefully.

There are a bunch of elements you may require approval for like the structural integrity, appropriate insulation levels, or the construction of a building over drainage or sewage. In cases where it’s obvious that you’d need building regulations, you can simply submit the building and planning application together at once.

The roof is the place that your conservatory is most likely to get grubby, but cleaning it is easy. You shouldn’t need to use any powerful cleaners – just warm water and a mild detergent.

The best tool to use to access your conservatory roof is a telescopic brush. This will help you get into corners and high areas without needing to work from height. You can use a ladder to help you clean your conservatory roof, but you should be very careful to avoid leaning it against any glazing

.

Consider investing in a telescopic cleaner with squeegee, brush and mop attachments to help you achieve a great finish on your aluminium conservatory.

A polycarbonate conservatory roof is made using a polycarbonate which is a contemporary plastic material that features several beneficial properties which gives it a high optical clarity as well as a good durability. Visually, it’s very similar to glass but its a lot more resistant to impact  which makes it just as strong as some metals. As a result, there are a lot of cases where polycarbonate is used as a replacement for security windows and more. If you happen to possess a polycarbonate conservatory, then you’d probably like to know how you can fix it in case of any damages. In this post, we’re going to consider how to repair polycarbonate conservatory roofs. Let’s take a look!

There are a bunch of effective methods you can consider for fusing or gluing polycarbonate plastic. Glues will leave an adhesive behind, while fusing results in a chemical reaction which enables the material to melt back together. Here is a great method you can use to repair polycarbonate plastic:

• Use of methyl methacrylate. Due to the fact that this creates a strong, resilient bond, methyl methacrylate is the best way to fuse polycarbonate. According to some of the users, if they try to pull the polycarbonate apart the unaffected part will break before the bond does. During the application of methyl methacrylate, you’d have to ensure you’re in a well ventilated area or outdoor. This is because the fume generated from methyl methacrylate can be toxic if it’s inhaled in a high concentration.