Find an Electrician you can trust in Ballyclare.

Unlike in houses built in the 1970s where a good majority of the houses will not need to be rewired, for houses built in the 1960s you’d probably need to rewire the entire house unless the wiring is the modern PVCu coated type. Generally, the homes built especially in the 1960s and 1970s brought about enormous changes. This is because over the years our way of living began to change and as a result, our need for electricity became even greater. In response to this, the electrical systems we incorporate needed to change in order to match the new set standards.

In the 1960s, the amperage normally used was increased to 100, which enables home and property owners to power their dishwasher, microwave as well as refrigerator all on one circuit. However, while this may be a remarkable improvement for our grand parents, this is just enough to cater for our modern day appliances. In recent times, new homes are constructed using a wide range of dedicated circuits due to the fact that each of our appliances makes use of much more electricity to function. Consequently because the 100 amp panels of the 1960s possessed restricted space for breakers, home and property owners who still had the units in their homes will inevitably require a sub panel or a new panel entirely - meaning a total rewiring of their property.

Furthermore in the 1960s, builders turned to aluminium from the previously used copper as it was a great conductor and also happens to be relatively cheap. However, after a couple of years a host of electrical fires cropped up in houses that are wired using aluminium. It was later discovered that when the switch to aluminium was made, the light switches or receptacles which were originally made for the previously used copper was overlooked. It was learned that there’s a corrosive chemical reaction that arises as a result of the two dissimilar metals when connected. Hence, the more reason why aluminium wired houses in the 1960s needs to be rewired.

There are two different types: flat plate, where lots of thin tubes carry water through a flat absorber panel, and evacuated tube, where vacuum glass tubes capture the sun’s energy directly. There is little difference in performance between the two but evacuated tube panels do more obviously extrude from the roof.

Fuse box prices will vary and a periodic inspection should be carried out first. However, domestic fuse boxes cost an average of £460. A qualified electrician will advise if yours needs to be replaced and it's always a good idea to obtain a number of quotes before committing to this.

Electric heating has several benefits. It can be paired with renewable electricity generation, so the electricity used to heat your home will be sustainable. Underfloor heating is very efficient and can be cheaper than comparable gas or oil fired systems.

If you’re about to acquire an electrical safety certificate, it’s quite normal to be a bit curious about the length of time the certificate is expected to last for. Well, this is also a bit tricky as the duration is determined by your type of property. In this post, we aim to shed more light into this topic in order to give you a detailed insight and help you make informed decisions moving forward.

As earlier stated, the validity of your electrical safety certificate or report is based on the type of property you own. In event whereby you happen to have tenants living in the property, the electrical safety certificate will last for 5 years or with every change of tenancy, depending on whichever comes first. However, in the event whereby you happen to live in your property, the electrical safety certificate is going to remain valid for 10 years. What’s more? For commercial properties, the electrical safety certificate is also valid for only 5 years. Meanwhile for caravans and swimming pools, the electrical safety certificate possesses a shorter lifespan of just 3 year and 1 year respectively.

The suggested length of validity is only the industry standard. And as such, landlords are not under any legal obligation to get their electrical safety certificate updated at the aforementioned times. According to the Landlord and Tenant Act of 1985, landlords are only required to keep the electrical wiring in proper condition at all times. It does not in any form require landlords to get an electrical safety report or certificate.

One of the primary reasons why you need to get an electrical certificate is that you may not be allowed to show legal proof that the wiring and electrical set up in your property was in the best possible condition in the event of an electrical accident. Several insurance companies will not accept your claims if you’re unable to present the electrical safety certificate.

Also commonly referred to as a consumer unit in recent times, a fuse box is responsible for controlling and allocating of the electricity in your home. They hold the power any time there’s an overload in one of the circuits which in turn, prevents fire as well as electrical damage. Fuse boxes are often incorporated in homes but consumer units are very rapidly replacing them. Therefore, when your fuse box breaks down, it’s always a smart decision to replace them with consumer units due to the fact that they’re safer and also comply with building regulations while also being a lot easier to use. If you’re extending your home, upgrading to a larger capacity model enables you to make use of more power with the power overloading. In this post, we’re going to cover the amount you’re expected to pay to replace or install a new fuse box or consumer unit as well as the factors that may affect the cost.

For a 10 way dual RCD consumer unit, the typical cost range will be between £250 to £600, meanwhile 15 way dual RCD consumer unit should cost within the range of £300 to £700. Overall, the smaller the house, the fewer the circuits that’ll be needed, hence the difference in the aforementioned prices.

There a number of factors that can affect the cost of replacing a fuse box. These factors includes the the size of the house in question ( the bigger the house , the more the circuits there are and the bigger the fuse box needed), the location ( for instance, places like London where there are higher demands are likely to be more expensive than other regions ).

It might be possible to fit electrics in your shed, depending on where it is and what it’s made of. You should get in touch with a qualified electrician to find out whether it’s possible. Never attempt to run electrical cable from your house to an outbuilding!

How Much Does Pat Testing Cost?

When it comes to Portable Appliance Testing (PAT) there’s no particular rule that determines how much such services can cost. However as a rule of thumb, you should take note that when calling in a professional PAT testing company they’re likely to charge within the range of £1 to £3 per appliance that’s going to be tested. However, if you have quite a number of appliances to be tested, then there’s a good chance that the price per appliance can be reduced to serve as a bulk discount. So the more the appliances to be tested, the better.

There are companies that actually offer a pricing that’s below £1 per item, however companies likely are most definitely going to have a fixed minimum number of appliances that are required to be tested or a fixed minimum fee like 60 portable appliances. It must, however, be noted that pricing can also go beyond PAT Testing as several professional companies will add some additional advantages which is more than just the test of each individual appliance. This kind of pricing can include other services such as a thorough visual inspection, plug rewiring as well as fuse replacements. They can also include stuffs like Pail and Fail labels in the pricing.

Generally, the average price of PAT testing will be based on various influencing factors such as the type of the appliance, setting, number of appliance to be tested as well as other related expenses. What’s more? Most PAT companies will offer a company with a PAT Testing Certificate so as to certify that the company is in total compliance and also remains a safe environment to work.