Find an Electrician you can trust in Broadstone.

If you’re looking to install a solar thermal system in your home, this is usually one of the first concerns several homeowners have. Being fully aware that solar water heating systems are usually more expensive than their counterparts - the conventional water heating systems, the question arises whether or not you’ll be able to save some money from your solar water heating system in the long run. In this article, we aim provide an answer to this important question. Let’s take a closer look!

When it comes to solar thermal systems, the money you’ll be able to save in the long run depends on a wide range of factors. These factor includes:

✓ Your system’s performance.

✓ Your geographical location and solar resource

✓ Your household’s hot water demand

✓ Financing and incentive options that are available.

✓ The cost of fuel that’s being used for your alternative or backup water heating system, if you own one.

✓ The cost of conventional fuels such as oil, electricity or natural gas.

There are several benefits, however, that comes with the installation of a solar water heating system. Since the sun is absolutely free, future fuel shortages and price hikes will have little impact on you. Also, on the average if you decide to fit a solar thermal system your water heating bills is expected to drop about 50 percent to 80 percent. What’s more? The economics are even a lot more attractive when you’re just about to build a new home or refinancing. When you include the price of a solar water system in a 30 year mortgage, it’ll normally amount to very low price per month. Therefore, on a monthly basis you’ll be saving more and paying less.

There are two different types: flat plate, where lots of thin tubes carry water through a flat absorber panel, and evacuated tube, where vacuum glass tubes capture the sun’s energy directly. There is little difference in performance between the two but evacuated tube panels do more obviously extrude from the roof.

Tesla’s top-of-the-range battery storage system is still one of the most expensive on the market. It has a huge 13.5kWh usable capacity and can even keep you up and running during a power cut. But how long does a Tesla Powerwall battery last? And does this mean it’s worth investing in one?

The Tesla Powerwall 2.0 comes with a 10-year warranty. But Tesla says that it should last way beyond this – at least 5 years longer. The standard warranty says that it should work at 70% capacity for the full 10 years – so if it loses more than 30% of its storage capacity within that time, it should still be covered.

While the Tesla Powerwall does last a long time, it has a large capacity that most average households won’t require, and it’s a costly option. After installation, the Powerwall 2.0 will set you back between £6,500 and £9,000, so ideally you want it to last past its 10-year warranty.

Before you splash out, consider the size of the solar panel system you want to install or you already have. Will it generate enough electricity to make it worth storing in the Powerwall? If not, are you expecting to upgrade your solar panels to a larger system in the future? If you are, then it might be worth investing in a Powerwall. It might also be better to wait until you come to upgrade your solar panels – the solar battery price trend is going the same way as solar panels, so they will probably continue to decrease in price as more people adopt the technology.

The importance of selecting the right size battery for your home simply cannot be overemphasized. A lot of home and property owners are facing this challenge and understandably so. Selecting the right battery size for your needs depend on a number of factors which includes your motive for adding a battery, your electricity usage, your budget as well as your panel array size, be it new or existing. In this post, we’re going to take you through some of these factors to help you determine the right battery size for your home or property. Let’s take a look!

• Your motive for getting a battery. While most people purchase a battery to wipe out their need to purchase electricity from the grid with the hope of making some savings, others add a battery so as to enjoy backup power. There are also some who just needs it to power their home with solar energy. It’ll not be economical to size a battery to effectively take you off the grid, but if your motive is to make savings, then you’ll should expect to purchase some electricity from the grid during the year.
• Electricity usage. The average household uses about 16kWh of electricity on a daily basis. During the daylight hours, most of these household will use a third of their electricity when the solar panels are still generating electricity, while the remaining two third are purchased from the grid. In other words, you’ll require a minimum of 10kWh battery capacity if you were to use a battery to power the electricity you purchase from the grid.

For a typical British household, you’ll most likely need a 5kWh solar power system which normally generates about 17 to 21 kWh on a daily basis depending on your location in the UK.

If you’re a home or property owner planning to get an electric vehicle, having a Level 2 charger installed in your garage or near your driveway can go a long way to make charging really convenient for you. So if at all you want to take on this task by yourself, you should ensure to do it the right way. If you lack the confidence or skills required to pull this off, then we’d strongly recommend you hire the services of a professional who can guarantee the best results the first time. In this post, we’re going to provide you with an good insight on the home electric charger installation process. Let’s take a look!

• Determine the eligibility of your home. Make sure your home is eligible for a charger installation by consulting with your Technical Safety BC.
• Confirm you have sufficient electricity supply. Is there enough electricity distributed to your home to support an ev charger?
• Confirm that your electrical panel has enough space to accommodate a circuit breaker for the electric vehicle charger. If not, you’ll need to hire the services of an electrician.
• Get an electrical permit. Apply for an electrical permit with your municipality or Technical Safety BC.
• Charger installation. Proceed to fit the ev charger, but make sure a safety officer is on hand to examine your electrical work before you conceal any wiring or attach to a supply source. Then your electrician will have to complete the contractor consultancy form once the installation is done.
• Inspection. The inspection should be inspected by your municipality or Technical Safety BC.
• Apply for a rebate.

If you’re planning to get an electric vehicle, the next thing that naturally comes to mind is getting a good charger with it. As a result, this is one of the most common questions asked when it comes to electric vehicles. We’ve put together this list of some great home ev chargers to help you make the best informed decision possible moving forward. Let’s take a look!

• Charge Point Wi-Fi Enabled Level 2 EV Charger. If what you need is a faster charge for your car due to the high frequency of usage of the electric vehicle, then this charger might just be the best option for you. It’s claimed to charge electric vehicle batteries six times faster than a standard 120 volt home system. What’s more? The mobile application will inform you about the amount of charge your battery has regardless of your location. This feature can be of great benefit especially when you’re trying to determine whether to put in an additional hour at work or heat straight home.
• Juice Box Pro 40 Level 2 EV Charger. This is a level 2 charger which features a web based charging control so as to allow you control the charging parts of your vehicle from anywhere, be it in the comfort of your home or office without having to go to the garage or parking lot.
• Siemens VersiCharge VC30GRYU. This is an easy-to-use plug and play installation that comes with a mounting bracket if you happen to own a NEMA 50 receptacle. It boasts a charging time that’s 4 times faster than level 1 electric vehicle chargers and possess a charge delay feature or 2, 4, 6 or 8 hours.

If your fuse box keeps tripping or blowing fuses, it may need replacing. Other signs that your fuse box is not working properly include humming, sparking and lack of power. Contact an electrician and ask for a safety report, this will diagnose the problem and lead to a quick fix.

Unlike in houses built in the 1970s where a good majority of the houses will not need to be rewired, for houses built in the 1960s you’d probably need to rewire the entire house unless the wiring is the modern PVCu coated type. Generally, the homes built especially in the 1960s and 1970s brought about enormous changes. This is because over the years our way of living began to change and as a result, our need for electricity became even greater. In response to this, the electrical systems we incorporate needed to change in order to match the new set standards.

In the 1960s, the amperage normally used was increased to 100, which enables home and property owners to power their dishwasher, microwave as well as refrigerator all on one circuit. However, while this may be a remarkable improvement for our grand parents, this is just enough to cater for our modern day appliances. In recent times, new homes are constructed using a wide range of dedicated circuits due to the fact that each of our appliances makes use of much more electricity to function. Consequently because the 100 amp panels of the 1960s possessed restricted space for breakers, home and property owners who still had the units in their homes will inevitably require a sub panel or a new panel entirely - meaning a total rewiring of their property.

Furthermore in the 1960s, builders turned to aluminium from the previously used copper as it was a great conductor and also happens to be relatively cheap. However, after a couple of years a host of electrical fires cropped up in houses that are wired using aluminium. It was later discovered that when the switch to aluminium was made, the light switches or receptacles which were originally made for the previously used copper was overlooked. It was learned that there’s a corrosive chemical reaction that arises as a result of the two dissimilar metals when connected. Hence, the more reason why aluminium wired houses in the 1960s needs to be rewired.