Find an Electrician you can trust in Didcot.

Are you thinking about installing a solar thermal system in your home? If yes, the you’d most likely be wondering the exact amount the system is going to cost. Well, you’re not alone. This is one of the most common question when it comes to solar thermal systems and we aim to answer that in this article. So let’s get started!

Unfortunately, the cost of a solar thermal system can’t be given in a single, accurate answer as they vary widely. However, when getting a new solar thermal system, you can expect to pay a sum within the range of £3000 to £6000 ( this includes a lowered VAT rate of 5 percent). The figures provided takes into account the installation costs as well as all the parts ( such as control panel, solar collectors, hot water tank and pipes).

To determine the price of your system, the quality and type of the panels matter. For instance, according to the Solar Trade Association, a properly insulated twin coil cylinder system would be priced at around £4500. in the same tone, it’s also possible to get DIY solar thermal kits that includes all the required hardware which will cost within the range of £1500 to £250. This however, may not be eligible for government support. In order to benefit from the RHI, your system must be fitted by a MCS accredited installer.

The varying prices of the solar thermal system’s initial cost is based on the specification of each individual house. For example, in situations where the building is having complicated water system, the plumbing cost is expected to increase which will have a serious impact on the overall cost of the solar thermal power system.

Unlike in houses built in the 1970s where a good majority of the houses will not need to be rewired, for houses built in the 1960s you’d probably need to rewire the entire house unless the wiring is the modern PVCu coated type. Generally, the homes built especially in the 1960s and 1970s brought about enormous changes. This is because over the years our way of living began to change and as a result, our need for electricity became even greater. In response to this, the electrical systems we incorporate needed to change in order to match the new set standards.

In the 1960s, the amperage normally used was increased to 100, which enables home and property owners to power their dishwasher, microwave as well as refrigerator all on one circuit. However, while this may be a remarkable improvement for our grand parents, this is just enough to cater for our modern day appliances. In recent times, new homes are constructed using a wide range of dedicated circuits due to the fact that each of our appliances makes use of much more electricity to function. Consequently because the 100 amp panels of the 1960s possessed restricted space for breakers, home and property owners who still had the units in their homes will inevitably require a sub panel or a new panel entirely - meaning a total rewiring of their property.

Furthermore in the 1960s, builders turned to aluminium from the previously used copper as it was a great conductor and also happens to be relatively cheap. However, after a couple of years a host of electrical fires cropped up in houses that are wired using aluminium. It was later discovered that when the switch to aluminium was made, the light switches or receptacles which were originally made for the previously used copper was overlooked. It was learned that there’s a corrosive chemical reaction that arises as a result of the two dissimilar metals when connected. Hence, the more reason why aluminium wired houses in the 1960s needs to be rewired.

How Much Does Pat Testing Cost?

When it comes to Portable Appliance Testing (PAT) there’s no particular rule that determines how much such services can cost. However as a rule of thumb, you should take note that when calling in a professional PAT testing company they’re likely to charge within the range of £1 to £3 per appliance that’s going to be tested. However, if you have quite a number of appliances to be tested, then there’s a good chance that the price per appliance can be reduced to serve as a bulk discount. So the more the appliances to be tested, the better.

There are companies that actually offer a pricing that’s below £1 per item, however companies likely are most definitely going to have a fixed minimum number of appliances that are required to be tested or a fixed minimum fee like 60 portable appliances. It must, however, be noted that pricing can also go beyond PAT Testing as several professional companies will add some additional advantages which is more than just the test of each individual appliance. This kind of pricing can include other services such as a thorough visual inspection, plug rewiring as well as fuse replacements. They can also include stuffs like Pail and Fail labels in the pricing.

Generally, the average price of PAT testing will be based on various influencing factors such as the type of the appliance, setting, number of appliance to be tested as well as other related expenses. What’s more? Most PAT companies will offer a company with a PAT Testing Certificate so as to certify that the company is in total compliance and also remains a safe environment to work.

Smart EV charger is basically a set of functionalities in EVBox charging stations which allows the owner of the station to run several charging stations in a manner that’s cost effective and energy efficient. The word “smart, technologically speaking can mean a number of things, but generally it simply implies automation or your device’s ability to connect to other devices. Talking of smart ev chargers, this enables your charger to communicate with your car, the electric grid, as well as the ev charging infrastructure or other chargers. In other words, this means that any time you plug in your car to charge, the charger is able to transmit data to the charging operator. This operator can then make use of this data to identify the best time for you car to be charged and as a result, puts much less pressure on the grid and could also turn to be very cost effective in the long run.

Here are some of the primary benefits of smart ev charging

• They’re a lot quicker than three-pin plug. This is perhaps the most obvious benefit you can get from a smart ev charger. Overall, the charging time is much shorter due to fact that it possesses up to 3 times the power of a three pin plug.
• Schedule the charging to suit your lifestyle. If your ev home charger is connected to the internet, there are additional benefits you can derive from it. These includes being able to sync it with your calender. Once you add your schedule to the smart charger app, your ev will be well charged and ready to go any time it’s needed.

If you’re considering getting a solar thermal system, one of the first things that comes to mind is the possibility of the system functioning properly during the cold months. The short and simple answer to this question is yes, a solar thermal system works in the winter. However, the downside here is that it’ll be a lot less efficient when compared to how it operates during the warmer months or summer. As a result of this fact, you’ll likely need to rely more on your boiler, immersion heater or any other backup heating system during this period as your solar thermal system will fail to contribute as much as it does during the warmer months. So what exactly is the reason why solar thermal is less effective and less efficient in the winter period? Let’s have a look!

As you know, solar thermal system banks on the sun’s energy to heat the water for your home’s use. During the cold months or winter, the sunlight becomes a lot less available when compared to the warmer months, as a result, there’s less sunlight that’s available to be used for its solar energy. And even more so at the periods when the days are shorter or skies are clearly overcast.

Also having a great impact on a solar thermal system’s output is heavy snow. Flat plate collectors normally have the capacity to cope better during snowy conditions as the light that’s able to travel through the snow will heat up the absorber plate - thereby making the snow slide off more quickly. However, the case is contrary with evacuated tube collectors which possesses a form of vacuum insulation that’s crafted to minimize the loss of heat, meaning they can’t generate heat to melt and cause the snow to slide off in a similar way.

If you’re a home or property owner planning to get an electric vehicle, having a Level 2 charger installed in your garage or near your driveway can go a long way to make charging really convenient for you. So if at all you want to take on this task by yourself, you should ensure to do it the right way. If you lack the confidence or skills required to pull this off, then we’d strongly recommend you hire the services of a professional who can guarantee the best results the first time. In this post, we’re going to provide you with an good insight on the home electric charger installation process. Let’s take a look!

• Determine the eligibility of your home. Make sure your home is eligible for a charger installation by consulting with your Technical Safety BC.
• Confirm you have sufficient electricity supply. Is there enough electricity distributed to your home to support an ev charger?
• Confirm that your electrical panel has enough space to accommodate a circuit breaker for the electric vehicle charger. If not, you’ll need to hire the services of an electrician.
• Get an electrical permit. Apply for an electrical permit with your municipality or Technical Safety BC.
• Charger installation. Proceed to fit the ev charger, but make sure a safety officer is on hand to examine your electrical work before you conceal any wiring or attach to a supply source. Then your electrician will have to complete the contractor consultancy form once the installation is done.
• Inspection. The inspection should be inspected by your municipality or Technical Safety BC.
• Apply for a rebate.

Most domestic solar thermal panels do not need planning permission and are covered by permitted development rights. There are restrictions on the size and location of these systems. If you live in a conservation area or listed building, or want to install a very large solar thermal system, check with your local authority to see if you will need planning permission.

How Much To Install Solar Panels And Battery?

Are you thinking about installing solar panels and battery in your home and wondering how much the installation is going to cost? Well, you’re not alone. This is one of the most commonly asked questions in the solar world, but unfortunately a precise answer can not be provided. This is mainly due to the fact that solar panel systems come in varying sizes which is the main influencing factor that determines how much electricity that can be generated. In other words, the larger the system, the more the electricity that’ll be produced to your home’s benefit.

Generally, for a solar system size of 1kW, the average cost of the solar panel ranges between £1800 to £1850, 2kW is between £3600 to £3700, solar panel size of 3kW ranges between £5500 to £5600 and finally, 4kW is between £6000 to £6050. For example, with the aforementioned prices in mind, the cost of solar panels for a standard 3 bedroom house will range between £5520 to £6040 as the high electricity demands will need the installation of 3 to 4kW solar system size.

Meanwhile the installation cost of solar batteries is also dependent on a number of influencing factors like the size as well as the make of the battery. Generally, you can expect to spend within the range of £500 to £2000 to install your batteries depending on aforementioned factors. In the event whereby you’ll be retrofitting, you might also need to include an additional cost of £1000 for an inverter. However, it’s important to note that there are only quite a few hybrid systems which are able to combine a battery storage with an inverter.