Find an Electrician you can trust in Haverfordwest.

If you’re thinking about installing a solar system in your home or property, this is probably one of the things you’d like to know before making a purchase decision. Well, you’ve come to the right place! In this post, we’re going to give you a good insight into this to help you make the best informed decision possible moving forward. Let’s take a look!

First and foremost, it must be stated that providing a short and accurate answer to this question is nearly impossible as the amount of time a solar panel will last after dark is influenced by a number of factors. These factors include the size of your solar system, the battery size as well as your power usage. As you would have imagined, batteries are charged when there is excess energy that’s being produced by your solar system but it’s not being incorporated to power your home or property. More often than not, this occurs during the sunlight’s peak periods from about 10am to 2pm.

The time it’ll take for your battery to charge is influenced by the size of your solar system in Kilowatts, the size of your battery as well as the rate in which your system is being used. Your battery can be charged in a day or two, of course unless it’s an over-sized battery for your system.

When the sun sets and your solar panels can no longer directly run your appliances via electricity generation, the battery then kicks in. You will use about 1 to 2 kW’s of power if you’re watching TV, using the oven as well as lights internet etc. in other words, even a small solar panel battery will last all night. However, the same doesn’t apply if you’re having a party with running floodlights, three fridges and air conditioner as the battery will drain a lot faster.

Obviously the performance of a solar thermal system will vary depending on the location of the home, the insulation of the property, and your own hot water requirements. Solar thermal panels are capable of providing all of your hot water requirements from April to September. They will still make a contribution to your hot water needs for the rest of the year, but in general you will need a backup system to further heat the water in the colder months.

Unlike in houses built in the 1970s where a good majority of the houses will not need to be rewired, for houses built in the 1960s you’d probably need to rewire the entire house unless the wiring is the modern PVCu coated type. Generally, the homes built especially in the 1960s and 1970s brought about enormous changes. This is because over the years our way of living began to change and as a result, our need for electricity became even greater. In response to this, the electrical systems we incorporate needed to change in order to match the new set standards.

In the 1960s, the amperage normally used was increased to 100, which enables home and property owners to power their dishwasher, microwave as well as refrigerator all on one circuit. However, while this may be a remarkable improvement for our grand parents, this is just enough to cater for our modern day appliances. In recent times, new homes are constructed using a wide range of dedicated circuits due to the fact that each of our appliances makes use of much more electricity to function. Consequently because the 100 amp panels of the 1960s possessed restricted space for breakers, home and property owners who still had the units in their homes will inevitably require a sub panel or a new panel entirely - meaning a total rewiring of their property.

Furthermore in the 1960s, builders turned to aluminium from the previously used copper as it was a great conductor and also happens to be relatively cheap. However, after a couple of years a host of electrical fires cropped up in houses that are wired using aluminium. It was later discovered that when the switch to aluminium was made, the light switches or receptacles which were originally made for the previously used copper was overlooked. It was learned that there’s a corrosive chemical reaction that arises as a result of the two dissimilar metals when connected. Hence, the more reason why aluminium wired houses in the 1960s needs to be rewired.

There are two different types: flat plate, where lots of thin tubes carry water through a flat absorber panel, and evacuated tube, where vacuum glass tubes capture the sun’s energy directly. There is little difference in performance between the two but evacuated tube panels do more obviously extrude from the roof.

Are Electric Radiators Expensive To Run?

Just like many home additions, the running costs of electric radiators varies largely on a number of factors. Great number of electric radiators typically comes with an in built thermostat which is designed to turn itself off automatically when not in use in order to save energy.

However the energy provider’s set electricity charge tariff will also have a great influence on an electric radiator’s running cost. Let’s take a look at the running costs of an electric radiator!

A 600 Watt electric radiator ( on a standard electricity tariff) will usually have a running cost ranging between 4 to 6 pence each hour. However you should also take note that this scenario might change in situations whereby the electric radiator is not calling for heat the full 60 minutes of each hour. And this is more likely to be the situation as the thermostat is programmed in such a way that enables it to turn itself off immediately there’s an achievement of your required room temperature level - usually within 10 minutes from the time it was switched on. As a result of this, the running cost per hour of electric radiators will be greatly reduced to just about 1 to 2 pence.

It’s also important to note that enhancing the insulation of your home can go a long way to add to the heat retention value of each room. Consequently, the duration at which the electric radiator calls more heating will be significantly reduced, which in turn, implies a lower electricity bill.

Another key factor that can play a huge role in saving on your heating bills is the programming as well as usage of your electric radiators. Every radiator comes with an independent digital thermostat with a number of 24/7 programming options to help achieve maximum efficiency. When the radiator is properly set according to your lifestyle, you can save as much as 50 percent on your heating bills.

Asides from the fact that solar energy can be converted into electricity with the help of solar panels, there’s also another pretty cool way the sun’s power can be harnessed - solar thermal technologies. These technologies are able to convert sunlight into heat rather than power and these are in fact the very first solar energy products that were commercialized in the United Kingdom. Solar thermal panels, in a similar way to solar PVs, can help in minimizing your carbon footprint while also assisting you to save good money on your energy bills by providing the much needed coverage for your heating needs with the help of a renewable energy source that’s totally free.

Solar thermal panels provides some great benefits which is capable of making all homeowners in the UK consider installing one in their respective homes. Let’s take a closer look at these benefits.

✓ When compared to solar PV panels, they’re a more affordable heating option and also have a shorter payback period.

✓ Solar thermal panels are more efficient than PV panels due to the fact that the heat waves are able to hold more energy than sunlight and also because there’s no electricity transformation process.

✓ Solar thermal panels are able to operate in cold climates, strong wind as well as overcast weather, and make use of an energy storage system.

✓ They can help you save about 600kg of carbon dioxide emissions on an annual basis.

✓ Although most of the solar thermal panel systems come with a warranty usually within the range of 5 to 10 years, they’re able to last up to 25 years. What’s more? The require just a little maintenance, meaning the main cost you’d have to worry about is the cost of installation.

There’s a need to ensure that all the paperwork are in place,before putting your house up for sale on the property market. An very good example of such essential document is the Electrical Installation Certificate (EIC) which is used as a proof to attest to the fact that the electrical installation works carried out on the property in question was actually done and also whether or not it satisfies the building regulations. It’ll be a contravention of the law to put your house up for sale or actually sell it without producing this important document. Therefore, if you’re looking to sell your house you may wish to know the electrical documentations you need to complete the task. In this post, we aim to provide you an in depth insight into the electrical certificates needed to sell your house while also helping you make informed decisions along the process. Let’s take a look!

You’ll need to obtain two certificates in the event whereby the electrical work done was performed by a registered and qualified electrician. The two documents include:

• The Building Regulations Compliance Certificate - This is provided to confirm that the electrical works done complies with the Building regulations.
• The Electrical Installation Certificate (EIC), alternatively you can have a Minor Electrical Installation Works Certificate which is provided to confirm that the electrical works done satisfies the BS 7671.

In addition, the local building control body must be provided with a copy of these documents. In such an event whereby the electrical work was completed after 2013 and either it was done by yourself or by an individual who isn’t a registered professional, then there’s a need to make sure that work is inspected by a registered third party certifier within 5 days of completion. If the work is found to be satisfactory, you’ll be issued a copy of an Electrical Installation Condition Report.

It’s always recommended to use a certified electrician to carry out electrical work. They can self-certify that their work meets building regulations. While some parts of electric heating systems can be installed as a DIY project, the thermostat and other control wiring legally must be installed by a certified electrician. There are a range of competent persons schemes in operation.