Find an Electrician you can trust in Selkirk.

For most homeowners, rewiring a house is always a sore subject they’d prefer to avoid especially when they think of the expenses they’d have to incur or the mess and complexity that the project involves. However, this is a subject we’d all have to face sooner or later as an old wiring poses a lot of drawbacks, while an improper wiring can also prove to be more expensive and even cause more damage as it can lead to not only electrical shorts but also electrical fires. When a wire triggers a spark or a current overload, this can cause fire and the entire house may be down in ashes within a couple of minutes. Hence, one of the several reasons why house rewiring is just too important to ignore.

In this FAQ, we’re going to take you through the house rewiring process so as to ensure that your project is done to perfection. However, if you do not feel confident enough to pull this off, we’d strongly recommend you get in touch with a reliable electrical professional who can guarantee that a safe and effective work is done.

• Firstly, you’d have to upgrade the main service panel to a minimum of 100 amps
• Fit dedicated circuits in the service panel for all the home’s major appliances.
• Allow for a space of about 6 to 8 feet between electrical outlets throughout the house in order to cut out the need to run extension cords which could be a fire hazard.
• Install only three-prong type to avoid electrical shocks when fitting new outlets.
• Using ground fault circuit interrupters, fit outlets in the bathrooms, kitchen as well as outdoors. These outlets will shut themselves out so as to prevent electrical shock when wet.

If you’re thinking about adding new power sockets to your room, then you’ve come to the right place! This task can be a very tricky one especially if you don’t know how to go about it. If you don’t have the skills or experience necessary to pull this off, then we’d strongly recommend you hire the services of qualified and licensed electrician who can guarantee the best results for help. In this guide, we’re going to take you through the numerous steps you’d have to take to make sure your new power sockets is added successfully. Let’s take a look!

• All the power to the working area at the primary electrical panel should be turned off.
• Identify the cut area for individual electrical box.
• Pilot saw blade by drilling corner holes
• Drill into framing for wiring, if required
• Connect electrical wires to the electrical panel from the outlet box holes, pulling four feet through the wall.
• Attach white wires to silver screws as well as black wires to brass screws and also the ground wire.
• Incorporate electrical tape to tape around the box
• Connect the box to the wall and cover with the outlet plate
• Carry out the process for individual outlet needed
• De-energize the entire electrical panel by shutting off the house’s main breaker
• Fit an arc volt breaker by connecting white and black wire to the breaker
• Connect white wire from the new breaker directly onto the neutral bar of the electrical panel
• Finally, you can turn the main breaker back on.

If you are thinking of buying an electric vehicle, then one of the first things you’d have to put into consideration is charging. When it comes to charging of your electric vehicle, doing it at home is one of the most convenient things that comes with it. Not only do you get to avoid the fuel stations, but you’d also get to drive a car in a much cheaper way. Fitting an EV charger or wallbox at your residential space gives you the option to add miles to your battery in a lot faster manner than making use of a three pin plug. In fact, there are also some chargers that offers a lot more than just being a fast way to charge your vehicle.

So which home ev charger should you use? There are a wide range of options available in the market today, however you can get the perfect match for your vehicle by answering these few questions:

• Can you park two cars side by side? If yes, then a tethered charger might just be your most suitable option. A tethered cable is one that’s always connected to your home’s charger. One of the major benefits of using this is that you can get home and plug the charger straight it without having to fetch the cable or carry it around.
• Is size and design crucial? If yes, then you can consider wallbox chargers or untethered wallboxes which are smaller in size and minimalist in design.
• What if your WiFi isn’t accessible? If your WiFi signal is poor in the spot where the charger is to installed but your mobile phone signal is good, then Ohme is a good option to consider.

If you’re thinking of adding a solar battery to your home, you might be wondering whether or not it’s going to work in a power cut. If yes, then you’re not alone as this is one of the most common questions asked when it comes to solar batteries. In this post, we aim to provide you with a detailed answer to solve this concern once and for all.

The answer to this question is, it depends. The main reason why your solar batteries will usually not work or provide your home with the much-needed back up power is as a result of the several threats it poses. You should be aware that both your solar panels and battery are connected to the main grid. When a power cut occurs, your engineers will have to operate on the grid. If the solar panels or batteries are in operation at the period there’s a high chance the engineers would be electrocuted by the electricity that’s being produced. As a result of this, solar inverters are usually designed to automatically switch off once a power cut occurs. However, it should also be noted that if your solar battery possesses backup functionality, you’ll be able to make use of your solar energy in the event of a power cut. In other words, what determines if your home battery would work in a power cut is the availability or otherwise of a backup functionality.

Furthermore, you might also wish to know if your solar panels will continue to charge the battery in a power cut. Well, this depends on the type of backup system you possess. There are some more affordable batteries that are designed to automatically release their stored energy upon the detection of a power cut. And this is mostly because the battery inverter is usually smaller than the solar inverter which allows the energy from the solar inverter to the transmitted to the battery - risking an overload. However, if otherwise, then energy can continue to be transmitted to the battery until its fully charged.

It might be possible to fit electrics in your shed, depending on where it is and what it’s made of. You should get in touch with a qualified electrician to find out whether it’s possible. Never attempt to run electrical cable from your house to an outbuilding!

Also commonly referred to as a consumer unit in recent times, a fuse box is responsible for controlling and allocating of the electricity in your home. They hold the power any time there’s an overload in one of the circuits which in turn, prevents fire as well as electrical damage. Fuse boxes are often incorporated in homes but consumer units are very rapidly replacing them. Therefore, when your fuse box breaks down, it’s always a smart decision to replace them with consumer units due to the fact that they’re safer and also comply with building regulations while also being a lot easier to use. If you’re extending your home, upgrading to a larger capacity model enables you to make use of more power with the power overloading. In this post, we’re going to cover the amount you’re expected to pay to replace or install a new fuse box or consumer unit as well as the factors that may affect the cost.

For a 10 way dual RCD consumer unit, the typical cost range will be between £250 to £600, meanwhile 15 way dual RCD consumer unit should cost within the range of £300 to £700. Overall, the smaller the house, the fewer the circuits that’ll be needed, hence the difference in the aforementioned prices.

There a number of factors that can affect the cost of replacing a fuse box. These factors includes the the size of the house in question ( the bigger the house , the more the circuits there are and the bigger the fuse box needed), the location ( for instance, places like London where there are higher demands are likely to be more expensive than other regions ).

Unlike the photovoltaic (PV) power which works to turn a part of the electromagnetic radiation of the sun directly to electrons and electricity, a solar thermal can simply be referred to as the absorption of the sun’s heat for human use. As a result, the solar thermal has a wider range of uses than the PV does in several ways. This is due to the fact that the sun’s heat can be absorbed and transported via a medium and the stored energy incorporated for several great purposes such as to heat water, to heat and cool a home or living space, to prepare a meal as well as to generate electricity. All these functions are useful for both residential and commercial spaces.

There are generally three different ranges of solar thermal energy that are being used which includes the low temperature ( for heating, cooling as well as ventilation), the mid temperature ( used for preparing meals, heating hot water and the likes) as well as the high temperature ( used for generating electricity). To focus more on generating electricity, there are a wide array of ways through which the sun’s heat can be directed at creating electricity via a heat exchanger which operates to super heat water or inert gas to power an electricity- generating plant or to produce electricity via a Stirling engine.

In order to increase their output or make them more efficient, evacuated glass tubes are used to encircle the tubes which in turn helps them to collect more heat energy while also protecting them from re-radiating the heat energy absorbed. The trough are normal positioned north to south as well as to keep tabs on the travels of the sun throughout the day.

Most people want to connect solar panels to a battery when they’re not at home all day to use the electricity they generate, or generate more than they consume over a day. Solar batteries are a great way to maximise the savings on your energy bills since you can use every unit of electricity you generate.

If you want to connect your solar panels to a battery, the best – and safest – way is to ask an MCS-registered company to do it for you. They’ve had lots of training and hold qualifications in handling electricity and installing solar batteries, so they will be able to recommend the best battery for your solar panels and for the among of electricity you use. Some of the brands they might recommend include Tesla, SolarEdge and SolaX, but there are many more to choose from. If you want to send electricity to the grid from your battery to receive Smart Export Guarantee (SEG) payments, it’s also worth leaving installation up to a registered installer. This is because you might not be eligible for payments if your battery wasn’t installed by an MCS-registered company.

However, if you do want to have a go at connecting your solar panels to a battery, it’s worth finding out whether your system is ‘storage ready’. Most relatively new systems will be, since batteries are becoming more commonplace. If your solar panels are storage ready, they will have an inverter that can easily have a battery added to it. If this is the case, then you should be able to buy the solar battery you want and follow the manufacturer's instructions to install it.

But it’s worth remembering that electricity is extremely dangerous when handled improperly. If you don’t get the solar battery connected properly and something goes wrong, it could cause a fire or you could electrocute yourself. If a fire breaks out due to your battery, it’s unlikely that your home insurance company would pay out since you connected the battery yourself. That’s why it’s always worth speaking to a registered installer to install a solar battery storage system for you.