Find an Electrician you can trust in Church Stretton.

If your fuse box keeps tripping or blowing fuses, it may need replacing. Other signs that your fuse box is not working properly include humming, sparking and lack of power. Contact an electrician and ask for a safety report, this will diagnose the problem and lead to a quick fix.

The OLEV Grant, also known as Electric Vehicle Homecharge Scheme (EVHS) can reduce the cost of your home charger by up to £350. If you're eligible, you'll be able to claim it when you buy an EV charger.

If you’re thinking about adding new power sockets to your room, then you’ve come to the right place! This task can be a very tricky one especially if you don’t know how to go about it. If you don’t have the skills or experience necessary to pull this off, then we’d strongly recommend you hire the services of qualified and licensed electrician who can guarantee the best results for help. In this guide, we’re going to take you through the numerous steps you’d have to take to make sure your new power sockets is added successfully. Let’s take a look!

• All the power to the working area at the primary electrical panel should be turned off.
• Identify the cut area for individual electrical box.
• Pilot saw blade by drilling corner holes
• Drill into framing for wiring, if required
• Connect electrical wires to the electrical panel from the outlet box holes, pulling four feet through the wall.
• Attach white wires to silver screws as well as black wires to brass screws and also the ground wire.
• Incorporate electrical tape to tape around the box
• Connect the box to the wall and cover with the outlet plate
• Carry out the process for individual outlet needed
• De-energize the entire electrical panel by shutting off the house’s main breaker
• Fit an arc volt breaker by connecting white and black wire to the breaker
• Connect white wire from the new breaker directly onto the neutral bar of the electrical panel
• Finally, you can turn the main breaker back on.

Solar thermal panels work by capturing heat directly from the sun and using it to heat water. This hot water is then passed through a coil to heat the water for your central heating system. Solar thermal systems are compatible with many existing conventional boilers with hot water tanks, and can be set up to feed in to your existing heating system.

Also commonly referred to as a consumer unit in recent times, a fuse box is responsible for controlling and allocating of the electricity in your home. They hold the power any time there’s an overload in one of the circuits which in turn, prevents fire as well as electrical damage. Fuse boxes are often incorporated in homes but consumer units are very rapidly replacing them. Therefore, when your fuse box breaks down, it’s always a smart decision to replace them with consumer units due to the fact that they’re safer and also comply with building regulations while also being a lot easier to use. If you’re extending your home, upgrading to a larger capacity model enables you to make use of more power with the power overloading. In this post, we’re going to cover the amount you’re expected to pay to replace or install a new fuse box or consumer unit as well as the factors that may affect the cost.

For a 10 way dual RCD consumer unit, the typical cost range will be between £250 to £600, meanwhile 15 way dual RCD consumer unit should cost within the range of £300 to £700. Overall, the smaller the house, the fewer the circuits that’ll be needed, hence the difference in the aforementioned prices.

There a number of factors that can affect the cost of replacing a fuse box. These factors includes the the size of the house in question ( the bigger the house , the more the circuits there are and the bigger the fuse box needed), the location ( for instance, places like London where there are higher demands are likely to be more expensive than other regions ).

The short and simple answer to this question is, no. If you’re a seasoned DIYer then you should probably know a thing or two about electrical works around your property. However, house rewiring works should only be carried out by a qualified and registered electrician for a handful of reasons. In this FAQ, we’re going to take an in depth look at a few reasons why a house rewiring project should always be tackled by a reliable professional.

• Risk. Not only do you out your own health and that of your loved ones at risk when you attempt to complete electrical rewires on your own, but you also put your property at risk. Tackling electrical works involves a great danger. These dangers can come in different forms such as electrical wires electrocution, shock as well as fire. What’s more? Items in your home also possesses higher voltages, and when it comes to electrical wiring, the higher the voltage, the more dangerous the project becomes. Another tricky task to get around is hidden junction boxes as well as connections. Since these components are out of sight, the chances of you getting shocked increases rapidly. All these risks can only be mitigated when proper procedures are followed . therefore, if you decide to do electrical work on your home, then there’s the need to obtain necessary permits for completing the work. Once completed, the work done should be inspected by a licensed electrical inspector. However, the best way to reduce the risks is by hiring the services of a licensed electrician.
• Safety. Electricians are trained to perfect their craft and comply with safety protocols. They’re also required to pass a licensing test so as to work as an electrician. The safety of your property and loved ones when it comes to your home’s electrical works can only be guaranteed when done by a qualified and registered electrician.

Unlike in houses built in the 1970s where a good majority of the houses will not need to be rewired, for houses built in the 1960s you’d probably need to rewire the entire house unless the wiring is the modern PVCu coated type. Generally, the homes built especially in the 1960s and 1970s brought about enormous changes. This is because over the years our way of living began to change and as a result, our need for electricity became even greater. In response to this, the electrical systems we incorporate needed to change in order to match the new set standards.

In the 1960s, the amperage normally used was increased to 100, which enables home and property owners to power their dishwasher, microwave as well as refrigerator all on one circuit. However, while this may be a remarkable improvement for our grand parents, this is just enough to cater for our modern day appliances. In recent times, new homes are constructed using a wide range of dedicated circuits due to the fact that each of our appliances makes use of much more electricity to function. Consequently because the 100 amp panels of the 1960s possessed restricted space for breakers, home and property owners who still had the units in their homes will inevitably require a sub panel or a new panel entirely - meaning a total rewiring of their property.

Furthermore in the 1960s, builders turned to aluminium from the previously used copper as it was a great conductor and also happens to be relatively cheap. However, after a couple of years a host of electrical fires cropped up in houses that are wired using aluminium. It was later discovered that when the switch to aluminium was made, the light switches or receptacles which were originally made for the previously used copper was overlooked. It was learned that there’s a corrosive chemical reaction that arises as a result of the two dissimilar metals when connected. Hence, the more reason why aluminium wired houses in the 1960s needs to be rewired.

Most people want to connect solar panels to a battery when they’re not at home all day to use the electricity they generate, or generate more than they consume over a day. Solar batteries are a great way to maximise the savings on your energy bills since you can use every unit of electricity you generate.

If you want to connect your solar panels to a battery, the best – and safest – way is to ask an MCS-registered company to do it for you. They’ve had lots of training and hold qualifications in handling electricity and installing solar batteries, so they will be able to recommend the best battery for your solar panels and for the among of electricity you use. Some of the brands they might recommend include Tesla, SolarEdge and SolaX, but there are many more to choose from. If you want to send electricity to the grid from your battery to receive Smart Export Guarantee (SEG) payments, it’s also worth leaving installation up to a registered installer. This is because you might not be eligible for payments if your battery wasn’t installed by an MCS-registered company.

However, if you do want to have a go at connecting your solar panels to a battery, it’s worth finding out whether your system is ‘storage ready’. Most relatively new systems will be, since batteries are becoming more commonplace. If your solar panels are storage ready, they will have an inverter that can easily have a battery added to it. If this is the case, then you should be able to buy the solar battery you want and follow the manufacturer's instructions to install it.

But it’s worth remembering that electricity is extremely dangerous when handled improperly. If you don’t get the solar battery connected properly and something goes wrong, it could cause a fire or you could electrocute yourself. If a fire breaks out due to your battery, it’s unlikely that your home insurance company would pay out since you connected the battery yourself. That’s why it’s always worth speaking to a registered installer to install a solar battery storage system for you.