Find an Electrician you can trust in Haverhill.

Unlike in houses built in the 1970s where a good majority of the houses will not need to be rewired, for houses built in the 1960s you’d probably need to rewire the entire house unless the wiring is the modern PVCu coated type. Generally, the homes built especially in the 1960s and 1970s brought about enormous changes. This is because over the years our way of living began to change and as a result, our need for electricity became even greater. In response to this, the electrical systems we incorporate needed to change in order to match the new set standards.

In the 1960s, the amperage normally used was increased to 100, which enables home and property owners to power their dishwasher, microwave as well as refrigerator all on one circuit. However, while this may be a remarkable improvement for our grand parents, this is just enough to cater for our modern day appliances. In recent times, new homes are constructed using a wide range of dedicated circuits due to the fact that each of our appliances makes use of much more electricity to function. Consequently because the 100 amp panels of the 1960s possessed restricted space for breakers, home and property owners who still had the units in their homes will inevitably require a sub panel or a new panel entirely - meaning a total rewiring of their property.

Furthermore in the 1960s, builders turned to aluminium from the previously used copper as it was a great conductor and also happens to be relatively cheap. However, after a couple of years a host of electrical fires cropped up in houses that are wired using aluminium. It was later discovered that when the switch to aluminium was made, the light switches or receptacles which were originally made for the previously used copper was overlooked. It was learned that there’s a corrosive chemical reaction that arises as a result of the two dissimilar metals when connected. Hence, the more reason why aluminium wired houses in the 1960s needs to be rewired.

If you’re thinking about installing a solar thermal system in your house, it’s always important to put into consideration numerous factors before you proceed. While some solar thermal systems are suitable for use at home, there are also some that are suitable for businesses or organizations which normally requires a big amount of hot water like hotels, restaurants, schools, hospitals and many more. You’ll also find some types available in the market that are suitable for communities to satisfy communal hot water demands.

It should, however, be noted that solar thermal systems do not have the capacity to produce all the hot water demand of a house. In the UK, an average household will need an annual water heating of between 3000kWh to 5000kWh. Whereas, a solar thermal system is only able to meet about 40 percent to 60 percent of this demand.

With that in mind, it’s also worth noting that during the summer months when the solar radiation is at its peak and hot water demand is relatively lower when compared to other seasons, a solar thermal system may be able to provide all of your household’s hot water needs. This implies that during this period you may not find the need to operate your boiler at all. However, during winter or colder months, when you have a higher hot water demands in contrary to a lower solar radiation, a solar thermal system will only be able to take care of about 20 percent of your household’s hot water needs. And that ultimately implies that during this period, you’ll need to rely more on a alternative or backup source of heat like gas, coal, electricity, oil or LPG.

The OLEV Grant, also known as Electric Vehicle Homecharge Scheme (EVHS) can reduce the cost of your home charger by up to £350. If you're eligible, you'll be able to claim it when you buy an EV charger.

Asides from the fact that solar energy can be converted into electricity with the help of solar panels, there’s also another pretty cool way the sun’s power can be harnessed - solar thermal technologies. These technologies are able to convert sunlight into heat rather than power and these are in fact the very first solar energy products that were commercialized in the United Kingdom. Solar thermal panels, in a similar way to solar PVs, can help in minimizing your carbon footprint while also assisting you to save good money on your energy bills by providing the much needed coverage for your heating needs with the help of a renewable energy source that’s totally free.

Solar thermal panels provides some great benefits which is capable of making all homeowners in the UK consider installing one in their respective homes. Let’s take a closer look at these benefits.

✓ When compared to solar PV panels, they’re a more affordable heating option and also have a shorter payback period.

✓ Solar thermal panels are more efficient than PV panels due to the fact that the heat waves are able to hold more energy than sunlight and also because there’s no electricity transformation process.

✓ Solar thermal panels are able to operate in cold climates, strong wind as well as overcast weather, and make use of an energy storage system.

✓ They can help you save about 600kg of carbon dioxide emissions on an annual basis.

✓ Although most of the solar thermal panel systems come with a warranty usually within the range of 5 to 10 years, they’re able to last up to 25 years. What’s more? The require just a little maintenance, meaning the main cost you’d have to worry about is the cost of installation.

Is Electric Heating Expensive?

Well, electric heating being termed as “expensive is relative to your budget. But we can tell you making use of electric heating will cost you within the range of an additional £300 to £400 per year more than the conventional gas powered systems. Meanwhile the average UK home making use of heating has been found to incur around £550 on an annual basis while those using electric storage heaters will spend almost £900 every year, according to OVO Energy.

However, there are numerous benefits of using electric heating and some of which can contribute to give a lower cost. If you’re considering the installation of an electric heating, here are some of the benefits you’ll derive.

• Safety. The several risks that comes with traditional systems are greatly reduced with an electric heating system. For instance, there’s no risk of carbon monoxide emissions or potential explosions since there’s no use of fuel to run the system.

• Installation. When compared to traditional systems, electric heating quite inexpensive to fit. This is due to the fact that minimal hardware are needed in the installation - no pipes, no flues, no vents and no ducts to be used. As a result, electric heating systems can also be installed within a shorter period of time.

• Environment. Generally, electricity has a positive impact on the environment especially due to the fact that there are no gasses or heavy metals incorporated in the system’s make up.

• Control. Electric heating offers a more convenient and controllable system. What’s more? This does not only make life easier, but can also help save as much as 30 percent on yearly cost of heating as well as helping to minimize toxic carbon emission. Furthermore, there’s a built in Wi-Fi that usually comes with electric heating systems while same can not be said of traditional gas systems.

For most homeowners, rewiring a house is always a sore subject they’d prefer to avoid especially when they think of the expenses they’d have to incur or the mess and complexity that the project involves. However, this is a subject we’d all have to face sooner or later as an old wiring poses a lot of drawbacks, while an improper wiring can also prove to be more expensive and even cause more damage as it can lead to not only electrical shorts but also electrical fires. When a wire triggers a spark or a current overload, this can cause fire and the entire house may be down in ashes within a couple of minutes. Hence, one of the several reasons why house rewiring is just too important to ignore.

In this FAQ, we’re going to take you through the house rewiring process so as to ensure that your project is done to perfection. However, if you do not feel confident enough to pull this off, we’d strongly recommend you get in touch with a reliable electrical professional who can guarantee that a safe and effective work is done.

• Firstly, you’d have to upgrade the main service panel to a minimum of 100 amps
• Fit dedicated circuits in the service panel for all the home’s major appliances.
• Allow for a space of about 6 to 8 feet between electrical outlets throughout the house in order to cut out the need to run extension cords which could be a fire hazard.
• Install only three-prong type to avoid electrical shocks when fitting new outlets.
• Using ground fault circuit interrupters, fit outlets in the bathrooms, kitchen as well as outdoors. These outlets will shut themselves out so as to prevent electrical shock when wet.

Unlike the photovoltaic (PV) power which works to turn a part of the electromagnetic radiation of the sun directly to electrons and electricity, a solar thermal can simply be referred to as the absorption of the sun’s heat for human use. As a result, the solar thermal has a wider range of uses than the PV does in several ways. This is due to the fact that the sun’s heat can be absorbed and transported via a medium and the stored energy incorporated for several great purposes such as to heat water, to heat and cool a home or living space, to prepare a meal as well as to generate electricity. All these functions are useful for both residential and commercial spaces.

There are generally three different ranges of solar thermal energy that are being used which includes the low temperature ( for heating, cooling as well as ventilation), the mid temperature ( used for preparing meals, heating hot water and the likes) as well as the high temperature ( used for generating electricity). To focus more on generating electricity, there are a wide array of ways through which the sun’s heat can be directed at creating electricity via a heat exchanger which operates to super heat water or inert gas to power an electricity- generating plant or to produce electricity via a Stirling engine.

In order to increase their output or make them more efficient, evacuated glass tubes are used to encircle the tubes which in turn helps them to collect more heat energy while also protecting them from re-radiating the heat energy absorbed. The trough are normal positioned north to south as well as to keep tabs on the travels of the sun throughout the day.