Find an Electrician you can trust in Wednesbury.

Obviously the performance of a solar thermal system will vary depending on the location of the home, the insulation of the property, and your own hot water requirements. Solar thermal panels are capable of providing all of your hot water requirements from April to September. They will still make a contribution to your hot water needs for the rest of the year, but in general you will need a backup system to further heat the water in the colder months.

If you’re a home or property owner planning to get an electric vehicle, having a Level 2 charger installed in your garage or near your driveway can go a long way to make charging really convenient for you. So if at all you want to take on this task by yourself, you should ensure to do it the right way. If you lack the confidence or skills required to pull this off, then we’d strongly recommend you hire the services of a professional who can guarantee the best results the first time. In this post, we’re going to provide you with an good insight on the home electric charger installation process. Let’s take a look!

• Determine the eligibility of your home. Make sure your home is eligible for a charger installation by consulting with your Technical Safety BC.
• Confirm you have sufficient electricity supply. Is there enough electricity distributed to your home to support an ev charger?
• Confirm that your electrical panel has enough space to accommodate a circuit breaker for the electric vehicle charger. If not, you’ll need to hire the services of an electrician.
• Get an electrical permit. Apply for an electrical permit with your municipality or Technical Safety BC.
• Charger installation. Proceed to fit the ev charger, but make sure a safety officer is on hand to examine your electrical work before you conceal any wiring or attach to a supply source. Then your electrician will have to complete the contractor consultancy form once the installation is done.
• Inspection. The inspection should be inspected by your municipality or Technical Safety BC.
• Apply for a rebate.

It’s always recommended to use a certified electrician to carry out electrical work. They can self-certify that their work meets building regulations. While some parts of electric heating systems can be installed as a DIY project, the thermostat and other control wiring legally must be installed by a certified electrician. There are a range of competent persons schemes in operation.

Home electrics can be extremely dangerous and it’s very unwise to try and carry out repair work or maintenance yourself without the necessary knowledge and skill. Therefore we would always recommend using a Part P registered electrician at all times.

For most homeowners, rewiring a house is always a sore subject they’d prefer to avoid especially when they think of the expenses they’d have to incur or the mess and complexity that the project involves. However, this is a subject we’d all have to face sooner or later as an old wiring poses a lot of drawbacks, while an improper wiring can also prove to be more expensive and even cause more damage as it can lead to not only electrical shorts but also electrical fires. When a wire triggers a spark or a current overload, this can cause fire and the entire house may be down in ashes within a couple of minutes. Hence, one of the several reasons why house rewiring is just too important to ignore.

In this FAQ, we’re going to take you through the house rewiring process so as to ensure that your project is done to perfection. However, if you do not feel confident enough to pull this off, we’d strongly recommend you get in touch with a reliable electrical professional who can guarantee that a safe and effective work is done.

• Firstly, you’d have to upgrade the main service panel to a minimum of 100 amps
• Fit dedicated circuits in the service panel for all the home’s major appliances.
• Allow for a space of about 6 to 8 feet between electrical outlets throughout the house in order to cut out the need to run extension cords which could be a fire hazard.
• Install only three-prong type to avoid electrical shocks when fitting new outlets.
• Using ground fault circuit interrupters, fit outlets in the bathrooms, kitchen as well as outdoors. These outlets will shut themselves out so as to prevent electrical shock when wet.

There are two different types: flat plate, where lots of thin tubes carry water through a flat absorber panel, and evacuated tube, where vacuum glass tubes capture the sun’s energy directly. There is little difference in performance between the two but evacuated tube panels do more obviously extrude from the roof.

Also commonly referred to as a consumer unit in recent times, a fuse box is responsible for controlling and allocating of the electricity in your home. They hold the power any time there’s an overload in one of the circuits which in turn, prevents fire as well as electrical damage. Fuse boxes are often incorporated in homes but consumer units are very rapidly replacing them. Therefore, when your fuse box breaks down, it’s always a smart decision to replace them with consumer units due to the fact that they’re safer and also comply with building regulations while also being a lot easier to use. If you’re extending your home, upgrading to a larger capacity model enables you to make use of more power with the power overloading. In this post, we’re going to cover the amount you’re expected to pay to replace or install a new fuse box or consumer unit as well as the factors that may affect the cost.

For a 10 way dual RCD consumer unit, the typical cost range will be between £250 to £600, meanwhile 15 way dual RCD consumer unit should cost within the range of £300 to £700. Overall, the smaller the house, the fewer the circuits that’ll be needed, hence the difference in the aforementioned prices.

There a number of factors that can affect the cost of replacing a fuse box. These factors includes the the size of the house in question ( the bigger the house , the more the circuits there are and the bigger the fuse box needed), the location ( for instance, places like London where there are higher demands are likely to be more expensive than other regions ).

The OLEV Grant, also known as Electric Vehicle Homecharge Scheme (EVHS) can reduce the cost of your home charger by up to £350. If you're eligible, you'll be able to claim it when you buy an EV charger.