Find an Electrician you can trust in Newton Stewart.

When it comes to electrical works, safety is always paramount. Although a complete house rewiring service may seem quite expensive, when compared to the safety it provides, you’d realize it’s well worth it. We know all too well that human nature tends to prevail to overlook small electrical issues until it’s too late or probably gets out of hands. When this happens, not only will you have to spend more to get the issue resolved, but it may also lead to some damages to your property. Hence, the need to identify and resolve electrical deficiencies as soon as possible. In this post, we’ve compiled a shortlist of some of the top signs that your house needs rewiring. Let’s take a look!

• Dimming or flickering lights. This is one of the most common signs that your house needs to be rewired. When a light brightens, it means there’s too much voltage and when it dims, it implies it’s receiving too little voltage. You may be tempted to think this is a lighbulb issue, but this type of decline in power is usually as a result of a loose wiring or faulty circuits which should not be ignored.
• Regularly blown fuses. With the steady development in technology as well as electrical appliances within our houses, older style fuses that are not designed to contain this amount of electricity will end up blowing. If your fuse blows on a more regular basis, then there may be a need to upgrade them to more modern circuit breakers.
• Lightbulbs burning out in their sockets. This is usually a sign of bigger issues in your wiring which is often caused by fluctuations in voltage.
• Sparking outlets. These can be perfectly normal, but at times they can also be a clear signal of a potentially dangerous problem which should not be ignored.

Unlike in houses built in the 1970s where a good majority of the houses will not need to be rewired, for houses built in the 1960s you’d probably need to rewire the entire house unless the wiring is the modern PVCu coated type. Generally, the homes built especially in the 1960s and 1970s brought about enormous changes. This is because over the years our way of living began to change and as a result, our need for electricity became even greater. In response to this, the electrical systems we incorporate needed to change in order to match the new set standards.

In the 1960s, the amperage normally used was increased to 100, which enables home and property owners to power their dishwasher, microwave as well as refrigerator all on one circuit. However, while this may be a remarkable improvement for our grand parents, this is just enough to cater for our modern day appliances. In recent times, new homes are constructed using a wide range of dedicated circuits due to the fact that each of our appliances makes use of much more electricity to function. Consequently because the 100 amp panels of the 1960s possessed restricted space for breakers, home and property owners who still had the units in their homes will inevitably require a sub panel or a new panel entirely - meaning a total rewiring of their property.

Furthermore in the 1960s, builders turned to aluminium from the previously used copper as it was a great conductor and also happens to be relatively cheap. However, after a couple of years a host of electrical fires cropped up in houses that are wired using aluminium. It was later discovered that when the switch to aluminium was made, the light switches or receptacles which were originally made for the previously used copper was overlooked. It was learned that there’s a corrosive chemical reaction that arises as a result of the two dissimilar metals when connected. Hence, the more reason why aluminium wired houses in the 1960s needs to be rewired.

If you’re planning to get an electric vehicle, the next thing that naturally comes to mind is getting a good charger with it. As a result, this is one of the most common questions asked when it comes to electric vehicles. We’ve put together this list of some great home ev chargers to help you make the best informed decision possible moving forward. Let’s take a look!

• Charge Point Wi-Fi Enabled Level 2 EV Charger. If what you need is a faster charge for your car due to the high frequency of usage of the electric vehicle, then this charger might just be the best option for you. It’s claimed to charge electric vehicle batteries six times faster than a standard 120 volt home system. What’s more? The mobile application will inform you about the amount of charge your battery has regardless of your location. This feature can be of great benefit especially when you’re trying to determine whether to put in an additional hour at work or heat straight home.
• Juice Box Pro 40 Level 2 EV Charger. This is a level 2 charger which features a web based charging control so as to allow you control the charging parts of your vehicle from anywhere, be it in the comfort of your home or office without having to go to the garage or parking lot.
• Siemens VersiCharge VC30GRYU. This is an easy-to-use plug and play installation that comes with a mounting bracket if you happen to own a NEMA 50 receptacle. It boasts a charging time that’s 4 times faster than level 1 electric vehicle chargers and possess a charge delay feature or 2, 4, 6 or 8 hours.

For most homeowners, rewiring a house is always a sore subject they’d prefer to avoid especially when they think of the expenses they’d have to incur or the mess and complexity that the project involves. However, this is a subject we’d all have to face sooner or later as an old wiring poses a lot of drawbacks, while an improper wiring can also prove to be more expensive and even cause more damage as it can lead to not only electrical shorts but also electrical fires. When a wire triggers a spark or a current overload, this can cause fire and the entire house may be down in ashes within a couple of minutes. Hence, one of the several reasons why house rewiring is just too important to ignore.

In this FAQ, we’re going to take you through the house rewiring process so as to ensure that your project is done to perfection. However, if you do not feel confident enough to pull this off, we’d strongly recommend you get in touch with a reliable electrical professional who can guarantee that a safe and effective work is done.

• Firstly, you’d have to upgrade the main service panel to a minimum of 100 amps
• Fit dedicated circuits in the service panel for all the home’s major appliances.
• Allow for a space of about 6 to 8 feet between electrical outlets throughout the house in order to cut out the need to run extension cords which could be a fire hazard.
• Install only three-prong type to avoid electrical shocks when fitting new outlets.
• Using ground fault circuit interrupters, fit outlets in the bathrooms, kitchen as well as outdoors. These outlets will shut themselves out so as to prevent electrical shock when wet.

If you’re considering getting a solar thermal system, one of the first things that comes to mind is the possibility of the system functioning properly during the cold months. The short and simple answer to this question is yes, a solar thermal system works in the winter. However, the downside here is that it’ll be a lot less efficient when compared to how it operates during the warmer months or summer. As a result of this fact, you’ll likely need to rely more on your boiler, immersion heater or any other backup heating system during this period as your solar thermal system will fail to contribute as much as it does during the warmer months. So what exactly is the reason why solar thermal is less effective and less efficient in the winter period? Let’s have a look!

As you know, solar thermal system banks on the sun’s energy to heat the water for your home’s use. During the cold months or winter, the sunlight becomes a lot less available when compared to the warmer months, as a result, there’s less sunlight that’s available to be used for its solar energy. And even more so at the periods when the days are shorter or skies are clearly overcast.

Also having a great impact on a solar thermal system’s output is heavy snow. Flat plate collectors normally have the capacity to cope better during snowy conditions as the light that’s able to travel through the snow will heat up the absorber plate - thereby making the snow slide off more quickly. However, the case is contrary with evacuated tube collectors which possesses a form of vacuum insulation that’s crafted to minimize the loss of heat, meaning they can’t generate heat to melt and cause the snow to slide off in a similar way.

Asides from the fact that solar energy can be converted into electricity with the help of solar panels, there’s also another pretty cool way the sun’s power can be harnessed - solar thermal technologies. These technologies are able to convert sunlight into heat rather than power and these are in fact the very first solar energy products that were commercialized in the United Kingdom. Solar thermal panels, in a similar way to solar PVs, can help in minimizing your carbon footprint while also assisting you to save good money on your energy bills by providing the much needed coverage for your heating needs with the help of a renewable energy source that’s totally free.

Solar thermal panels provides some great benefits which is capable of making all homeowners in the UK consider installing one in their respective homes. Let’s take a closer look at these benefits.

✓ When compared to solar PV panels, they’re a more affordable heating option and also have a shorter payback period.

✓ Solar thermal panels are more efficient than PV panels due to the fact that the heat waves are able to hold more energy than sunlight and also because there’s no electricity transformation process.

✓ Solar thermal panels are able to operate in cold climates, strong wind as well as overcast weather, and make use of an energy storage system.

✓ They can help you save about 600kg of carbon dioxide emissions on an annual basis.

✓ Although most of the solar thermal panel systems come with a warranty usually within the range of 5 to 10 years, they’re able to last up to 25 years. What’s more? The require just a little maintenance, meaning the main cost you’d have to worry about is the cost of installation.

How Does Electric Central Heating Work?

An electric central heating works to provide a number of benefits for you. These benefits include the following:

lSpace Heating

• The storage heaters work during the night to store electricity which would be used to heat up the heat retaining bricks. This, in turn, will release this energy throughout the day to warm up the room.

• There are also electric radiators which works to deliver on-demand heat and as a result, economy tariffs are totally avoided. It will generate heat by itself rather than storing it and with the controls, you can easily determine the amount of heat to be released when you require it.

• There is the wet electric system options as well which comes with water filled radiators. This operates in a similar way to normal radiators, however, it makes use of electricity to heat up the water.

lWater Heating

• An electric boiler operates in a very similar manner to other boiler types, just that it makes use of electricity as its fuel. Here, the water is warmed by a heating element and the water is later moved to several radiator throughout the house by a pump. These electric boiler types earns you tariff savings as you’ll be able to heat water at night.

• Heat pumps geothermal or air source, redistributes heat instead of creating it. Heat pumps are powered by electricity and it works by absorbing heat either from the air or ground which it then channels it through a pump. This can then be incorporated in heating either water or a room.

• A dedicated immersion heater is another water heating option. Here, the heating element is positioned inside a hot water cylinder. In a similar fashion to a kettle, the element heats the nearby water. Immersion heater can act either as a backup or your main heating element.

Fuse box prices will vary and a periodic inspection should be carried out first. However, domestic fuse boxes cost an average of £460. A qualified electrician will advise if yours needs to be replaced and it's always a good idea to obtain a number of quotes before committing to this.