Find a Flooring Fittter you can trust in Edgware.

How To Lay Wood Flooring

Laying of wood flooring is actually a very simple task contrary to many beliefs. First and foremost, before commencement of the fitting process, you must determine the direction you would like the engineered wood flooring to lie in. To do this the right way, they should lie in the direction of the the longest wall. However, if your subfloor is wooden, then having the boards positioned across the joists underneath would be your best bet to get started.

Here are some simple steps to follow to properly lay your wood flooring:

• Start from a corner, working from left to right and place the initial rows of the boards with the groove’s end directly opposite the closest wall.

• Make use of expansion spacers. Place them in between the wall and the board alongside an expansion gap of about 8 to 10mm.

• Place the board’s final rows at about 100mm wide. To achieve this, it is crucial to be pro-active with the measurement and cut the boards (if you deem fit) to adjust the first row.

• With the help of the click system, the boards will click together.

• Fit in the next board. Ensure to attach the tongues together (30 degrees from the floor) and once done, you can proceed to lower and lock it in place. Do this till you get to the end of the row.

• Cut the last board of the row to size if its too long.

• If the part cut off is up to 300mm, simply use it to start the next row. If not, cut a new board in half to use.

• Put the rows side by side in such a way to ensure the joints are staggered at each and every row. Keep a consistent gap between the wall and the planks via the continuous use of the spacers.

• Lay a plank over the last row to determine the width of the previous board. Position a new plank in a way that its tongue is directly against the wall. Once done, proceed to mark a line of plank underneath to get the required width. Then, fit the plank into the space with the help of a pull bar and hammer.

Click here to learn more about wood flooring.

If you’re thinking about making improvements to your home, it’s only reasonable to become familiar with the ins and outs of the requirements to make the project a success. Not just the cost involved to complete the project, but also the duration it’ll take to complete the job and lots more. When it comes to the installation of wooden flooring, there’s a need to find out whether or not an underlay is required for the task. In this article, we’re going to consider this in order to ensure that you’re on the right track. Let’s take a look!

First and foremost, underlays are common with carpets as they allow for an even surface with no lumps and bumps. It also provides a deeper barrier between the carpet and the floor as carpets, themselves, aren’t particularly thick enough to provide adequate comfort when walking on them. Underlay also helps improve insulation which in turn, helps cut down your energy bill. So, are underlays also needed with wooden flooring?

In general, wooden flooring does not really need an underlay. This is due to the fact that they’re perfectly comfortable to walk on without the need to add an extra padding underneath. However, the subfloor will have to be made prior to the installation, as a result, an underlay is needed at all there. With that in mind, it’s highly recommended to make use of an underlay when installing a boarded floor to a wooden subfloor mainly due to the fact that it’s able to provide a much-improved insulation. When it comes to wooden flooring, it’s always best to go for quality rather than looking for ways to cut corners. If you’re able to go for the best project with professional installation and little extras like undelay, you’d notice and enjoy the long lasting nature of your wooden flooring immediately after installation.

Installing wooden flooring is a quite simple process, however to get it right the first time, there are very essential preparations that must be made. These includes determining the site is in the best condition before installation, removal of all floor coverings and underlay for a more stable and durable installation and incorporation of the right expansion gap of about 10mm to 12mm which would be maintained around the floor’s perimeter.

Wooden floor fitting can be done on two types of sub-floor - Concrete and Plywood. To install onto concrete, you can follow the guide below:

• Incorporate flexible wood on concrete adhesives.

• With the help of a 3mm toothed trowel, spread above 2 board widths of adhesive along the starting wall sub-floor, beginning at a corner of your room.

• Position the first row of flooring into the area that is glued using the tongue facing opposite the wall.

• Put 10mm spacers against the wall to see to the consistency in expansion gaps.

• Make sure the joints are at a minimum of 150mm apart from the first row when fitting the second row.

• Utilize pre-cut smaller boards if you’re to start a new row with staggered joints.

• Continue with this nailing method and make sure the 10mm expansion gaps are consistent around the floor’s perimeter.

To install onto plywood, you can follow this guide:

• Make use of a porta-nailer.

• Position 10mm spacers against the wall - parallel with the installation direction.

• Fit the first row using the tongue facing opposite the wall and with the help of the porta-nailer or flooring nailer.

• Lay the second row and make sure the short end joints are at a minimum of 150mm apart from that of the first row.

• Utilize pre-cut smaller boards if you’re to start a new row with staggered joints.

• Continue with this nailing method and make sure the 10mm expansion gaps are consistent around the floor’s perimeter.

Click here to learn more about wood flooring.

If you’re replacing your carpet with new carpet, you might be able to use your old underlay. This is dependant on how long the existing carpet has been down for and also the condition of the underlay. But if you’re getting wood, laminate or vinyl flooring it’s not suitable. It will put stress on the joints if you use underlay.

The cost of just the engineered wood flooringis from £18 to £73 per m2.

One the several of the several benefits that comes with having a wooden floor installed is the fact that damaged surfaces can be repaired without the need to replace the floor in the whole room. This is not applicable to many other types of flooring whereby even the littlest damages are not reparable. Depending on the severity and depth of the wooden flooring damage, there are a number of techniques you can incorporate to repair the affected area. For examples, minor damages will not require as much effort as corner curling or cupping. In certain cases where the job requires no expertise, the repair process can be done by any individual with no prior experience in similar works. However, in other cases, when the wooden flooring has suffered a major damage, it’s advisable to call for a professional help.

First of all, it’s quite important to always watch out and prevent any sort of damages as this is way better than spending time trying to have the damaged surface repaired. One of the ways to prevent damages is by always lifting furniture rather than just dragging it across the floor when you need to move it. However, accidents are always meant to happen. In the case of damaged wooden flooring, here are some repair solutions.

When there are small scratches on your flooring, simply add a new coating of sealer to your floor (if the floor has already been oiled, just add another layer of oil). For lacquered floors, make use of a lacquer repair pen to help get rid of the scratches. In addition, there are some DIY shops offering wax filler sticks which can be used to hide or remove both light and medium scratches on wooden flooring.

Wooden flooring is very popular flooring option amongst home and property owners in the UK and understandably so. It adds to your space’s curb appeal, it’s quite easy to maintain, it adds to the value resale value of your property if you later wish to sell and lots more. If you’re looking to have wooden flooring installed in your home, you have two options which includes doing it yourself or calling in a professional – the latter being more advisable. However, by following some simple but essential steps, you can also install your wooden flooring successfully by yourself. These includes determining the site is in the best condition before installation, removal of all floor coverings and underlay for a more stable and durable installation and incorporation of the right expansion gap of about 10mm to 12mm which would be maintained around the floor’s perimeter.

Wooden floor fitting can be done on two types of sub-floor - Concrete and Plywood. To install onto concrete, you can follow the guide below:

• Incorporate flexible wood on concrete adhesives.
• With the help of a 3mm toothed trowel, spread above 2 board widths of adhesive along the starting wall sub-floor, beginning at a corner of your room.
• Position the first row of flooring into the area that is glued using the tongue facing opposite the wall.
• Put 10mm spacers against the wall to see to the consistency in expansion gaps.
• Make sure the joints are at a minimum of 150mm apart from the first row when fitting the second row.
• Utilize pre-cut smaller boards if you’re to start a new row with staggered joints.
• Continue with this nailing method and make sure the 10mm expansion gaps are consistent around the floor’s perimeter.

To install onto plywood, you can follow this guide:

• Make use of a porta-nailer.
• Position 10mm spacers against the wall - parallel with the installation direction.
• Fit the first row using the tongue facing opposite the wall and with the help of the porta-nailer or flooring nailer.
• Lay the second row and make sure the short end joints are at a minimum of 150mm apart from that of the first row.
• Utilize pre-cut smaller boards if you’re to start a new row with staggered joints.
• Continue with this nailing method and make sure the 10mm expansion gaps are consistent around the floor’s perimeter.

Getting the perfect carpet for your home can be seem as a bit tricky especially with the wide range of carpet options available in the market today. Most often than not, several home and property owners simply go to the store and purchase a carpet that they find the most aesthetically appealing and within their budget, neglecting its suitability for their homes. This can often turn out to be a disaster especially when there’s a total mismatch. For instance, when you have a busy household or thriving business with a heavy footfall, but you go on to install a carpet that’s not designed to withstand such a high traffic. If you’re looking to select the best carpet for your home, then you’ve come to the right place! In this post, we’re going to look how you can identify the best carpet for your home to help you make the best informed decision.

Basically, there are two carpet styles which includes loop pile and cut pile. For the loop style pile, individual ends are linked into the backing to ensure a continuous loop. While for the cut style pile, the loops are cut to ensure that each ends are sticking up through the backing - similar to a sheer cut pile.

Furthermore, fibre is critical material when it comes to carpet and the three main types of fibres used today includes polypropylene, polyester as well as nylon. Furthermore, the most popular choice today when it comes to natural fibre is wool. However, wool’s high price makes it less common and often considered as a luxurious option. For heavy traffic areas, the best carpets are usually loop pile styles to ensure maximum value is derived from your asset. On the other hand, if you want an easy-to-clean carpet, then olefin and polyester should be on the top of your list.