Find a Gutter Installer you can trust in Cleator Moor.

You can paint your soffits and fascias if they’re made of wood. In fact, it’s a good idea to do this every few years, as it can help to preserve them and keep them looking smart.

You can choose what you paint your soffits and fascias with by deciding what kind of look you want to achieve. You can stain them if you want to maintain a natural wood look, or use an exterior gloss or satin paint if you want to change their colour.

You should replace your soffits and fascias if you are having problems. Soffits and fascias can degrade and rot away over time, and this can cause leaks, faulty guttering, or even allow pests entry to the roof space. If any of these problems occur, you should speak to an experienced roofline company to discuss replacing your soffits and fascias.

You don’t always need to replace your gutters with your roof. Often people think that it’s a requirement, or simply the best thing to do, but it’s not always necessary. The reason why people think it’s required is because to re-roof a home, the guttering often needs to be removed and put back on.

If the time has come to replace your roof, then the chances are that your guttering is pretty old too. When you start to get quotes for your roof replacement, ask the roofer to take a look at your guttering as well. If there are signs of peeling, rust, cracks or sagging, then it makes sense to replace your gutters with your roof. If you get them done at the same time, you’ll save money labour costs, which is the reason why most homeowners do it.

Another reason to replace your gutters with your roof is the risk of damage. Re-roofing is a significant project, so the guttering needs to come off most of the time – running the risk of brackets and pipes getting damaged in the process. So if your guttering is still looking good right now but you think it might need replacing in a couple of years, it might be worth just doing it at the same time as your roof to save you money and the stress if damage does occur.

However, if your guttering has only recently been replaced, then there’s no need to replace it again with your roof. But because it needs to come off, make sure you speak to the roofing company about keeping it safe and doing their best to avoid damage. It’s also worse ensuring that they have the correct insurance to cover you both in case your guttering does get damaged during your roof replacement.

Clean of your conservatory gutter is probably not one of the most enjoyable chores you’d like to take on around the house. Not only is it messy and tedious, but it’s also time consuming and smelly. It’s a job every home and property owner would rather avoid, but unfortunately everyone has to do it. It’s a necessity due to the fact that neglect gutters holds and harbours mould, moss as well as plant debris. It would have been better if this is only disgusting, but the actual truth is that should be the least of your worries as this gradual build up of organic material in your conservatory gutters can minimize their drainage abilities, leading to leakages and spills that can damage your conservatory.

Cleaning of your conservatory gutter is a task that can be done regardless of your level of experience. However, it’s advisable to call in a professional for help especially if you lack the confidence required to pull it off.

• Use a ladder for a closer look. Cleaning your gutters from the ground by poking it with a hooked tool might seem the best way out, but in truth you risk damaging the gutters or brackets and marking the conservatory panes when you don’t see what you’re doing.
• Invest in specialist tools. For expert DIYers, taking off your downpipes from the wall to clean might be a pretty easy task. However, for most people it can be extremely frustrating. As a result, there’s the need to get hold of some flexible gutter brushes. With a bendable stem and stiff bristles, these are able to hook and dislodge dirt and leaves inside your downpipes with relative ease.

1. Hang a plumb bob from the outlet to the drain to use as a guide while you draw several marks on the wall with a pencil to show you where the downpipe will run.
2. Join the marks up with a straight edge, creating a line to show where the centre of the downpipe will be.
3. Position a downpipe clip at the top of wall, in the centre of the pencil line. Mark the position of its fixing holes on the wall. If you need an offset bend, put a downpipe clip directly below the bend.
4. Repeat the process down the wall. Make sure there is no more than 1.8 metres between pipe clips.
5. Refer to the guttering manufacturer’s instructions to see which drill bit is required. Use a drill to drill the fixing holes and insert wall plugs.
6. Fit the first piece of downpipe starting from the outlet and moving towards the drain.
7. If you need to add more downpipe, join the two pieces with a pipe socket and clip. Leave a 10mm gap between the end of the pipe and the bottom of the pipe socket, because it will probably expand. Then attach a pipe clip over the joint.
8. Continue attaching pipe clips down the length of the downpipe.
9. If you need to, fit a downpipe show to direct the water into the drain. Attach a downpipe clip directly below the socket of the shoe.

Soffits and fascias are available in lots of different colours. These include black, grey, brown, white and cream. It’s also possible to get them in brighter colours like reds, blues and greens.

What colour soffits and fascias you get is entirely up to you, unless you live in a listed building, in which case some rules may apply. Most people choose a colour that matches their roof, walls or window frames to give their property an attractive, colour-coordinated look.

Soffits and fascias sit along the sides of your property, over the join between your walls and your roof. The fascia attaches to the end of your roof rafters, hiding and protecting them. The soffit fixes on the bottom of the fascia, bridging the gap between your fascia and wall. Your guttering attaches to the fascia, which also joins to the bargeboard on your gable end, if you have one.

• A sturdy ladder
• Gloves and safety goggles
• A hammer and nails to secure your fascia so it doesn’t fall down mid-replacement
• A hacksaw – this will cut through uPVC guttering – just make sure you leave a margin of error with every cut you make
• Cable ties or rope to secure the existing gutters while you dismantle them, so they don’t fall off
• All the right fixings and brackets to secure the guttering
• An electric drill and/or screwdrivers

1. Add a gutter bracket to the top of the fascia board at the opposite end to the stop-end outlet, if you have one. Then tie a piece of string around the base of the bracket.
2. You’ll need to place the gutter outlet accurately over the drain. Hold a plumb line against the fascia directly over the drain, and mark that position with a pencil. Following the manufacturer’s advice on the number of screws to use, fit the gutter outlet no more than 50mm below the level of the roof tiles.
3. Stretch the piece of string you tied on the bracket along the fascia board, and tie it to the outlet. Make sure you check with a spirit level that the string slopes towards the outlet.
4. Mark the positions of the other brackets. They should be no more than 800mm apart, or 600mm if your roof is very steep. They also shouldn’t be any more than 150mm from a joint or fitting. Then fit the rest of the brackets.
5. Fit a stop-end to the first length of gutter and clip it into position on the brackets. At the other end, fit a union piece and screw it into the fascia.
6. Then fit the next length of gutter into it, and the next until you’re finished. Cut the last one to fit using your hacksaw before attaching a stop-end. Then make sure all the joints line up with the insertion depth marks on the fittings. Then you’re done!