Find a Gutter Installer you can trust in Dartford.

Having ventilation in the roof void is a requirement for building regulations approval. Fitting ventilated soffits is the typical way that this roof ventilation is achieved. If you do not have roof ventilation, you may find that your roof void has problems with condensation or overheating.

• A sturdy ladder
• Gloves and safety goggles
• A hammer and nails to secure your fascia so it doesn’t fall down mid-replacement
• A hacksaw – this will cut through uPVC guttering – just make sure you leave a margin of error with every cut you make
• Cable ties or rope to secure the existing gutters while you dismantle them, so they don’t fall off
• All the right fixings and brackets to secure the guttering
• An electric drill and/or screwdrivers

1. Add a gutter bracket to the top of the fascia board at the opposite end to the stop-end outlet, if you have one. Then tie a piece of string around the base of the bracket.
2. You’ll need to place the gutter outlet accurately over the drain. Hold a plumb line against the fascia directly over the drain, and mark that position with a pencil. Following the manufacturer’s advice on the number of screws to use, fit the gutter outlet no more than 50mm below the level of the roof tiles.
3. Stretch the piece of string you tied on the bracket along the fascia board, and tie it to the outlet. Make sure you check with a spirit level that the string slopes towards the outlet.
4. Mark the positions of the other brackets. They should be no more than 800mm apart, or 600mm if your roof is very steep. They also shouldn’t be any more than 150mm from a joint or fitting. Then fit the rest of the brackets.
5. Fit a stop-end to the first length of gutter and clip it into position on the brackets. At the other end, fit a union piece and screw it into the fascia.
6. Then fit the next length of gutter into it, and the next until you’re finished. Cut the last one to fit using your hacksaw before attaching a stop-end. Then make sure all the joints line up with the insertion depth marks on the fittings. Then you’re done!

Leaves, twigs and moss all have one thing in common which often annoys home and property owners - they are the three main materials that negatively impacts the proper functioning of a roof guttering system. The major cause of water drainage problems for most homes and buildings are these organic materials. Wondering how some leaves and few twigs can cause such a big problem? Over time there’ll be a gradual build up of the natural debris in your gutter system which starts to rot and turn  to a thick and muddy goo which obstructs the flow of water in your drainage. As a result, there’s the need to make sure that your gutters are thoroughly cleaned at least twice annually in order to prevent bigger issues that can be caused by the blockage of a drainage system.

So if you’re considering getting your gutters cleaned by a professional, you’d probably be interested in know just how it’s going to cost. Well, there’s not straightforward and simple answer to this question as there are a number of factors that contributes to the final cleaning cost of your gutters.

In general, in the UK, the average cost for cleaning of gutter is usually around £18 to about £25 per hour. However, you can also be quoted a day rate which is usually ranging between £150 to £200 per day.

The factors that can affect gutter cleaning price includes the type of your property (such as a terraced, end of terraced, detached and semi detached homes) which possesses a varying gutter cleaning price largely due to their size differences, the height of the building ( if you require the service for a property located on the second floor of a building, this would be a bit higher than if it were to be on the ground floor) as well as additional requests.

Gutters are a crucial component of any roofing system. They’re designed in such a way to protect your home or property from serious water damage, but keeping them clean and in good condition is something that’s almost always forgotten or ignored. Do not be deceived even when rain water is still running from them or they don’t appear to be clogged. Failure to clean maintain your gutters can lead to a wide range of outcomes and they aren’t so pretty. According to experts, gutter cleaning should be done twice a year - once in the spring and once in the fall. In order to help you realize the importance of cleaning your gutters, we’ll look at some of the possible outcomes of a neglected gutter.

• Leaky roof. If your gutters get clogged and cannot move water away from your home, it begins to build up on the roof and eventually lead to damages like rot and mold. As the damages spread, the end result could be a severe damage to the attic and supports.
• Damaged foundation. If the gutters are not functioning as they should, water saturation becomes a great threat to the foundation of your home or property. The concrete will crack or wood rots and you can also end up with mold.
• Creepy crawler infestation. Wherever you have stagnant water, there are also bugs. This is because they love the wet and moisture-filled gutters. You get unwanted visitors like carpenter ants, roaches and mosquitoes, just to mention a few.
• Driveway and path damage. When the downspouts aren’t directing the water to the appropriate spot, the excess that comes in contact with these surfaces can lead to cracks or sagging.

You don’t always need to replace your gutters with your roof. Often people think that it’s a requirement, or simply the best thing to do, but it’s not always necessary. The reason why people think it’s required is because to re-roof a home, the guttering often needs to be removed and put back on.

If the time has come to replace your roof, then the chances are that your guttering is pretty old too. When you start to get quotes for your roof replacement, ask the roofer to take a look at your guttering as well. If there are signs of peeling, rust, cracks or sagging, then it makes sense to replace your gutters with your roof. If you get them done at the same time, you’ll save money labour costs, which is the reason why most homeowners do it.

Another reason to replace your gutters with your roof is the risk of damage. Re-roofing is a significant project, so the guttering needs to come off most of the time – running the risk of brackets and pipes getting damaged in the process. So if your guttering is still looking good right now but you think it might need replacing in a couple of years, it might be worth just doing it at the same time as your roof to save you money and the stress if damage does occur.

However, if your guttering has only recently been replaced, then there’s no need to replace it again with your roof. But because it needs to come off, make sure you speak to the roofing company about keeping it safe and doing their best to avoid damage. It’s also worse ensuring that they have the correct insurance to cover you both in case your guttering does get damaged during your roof replacement.

Soffits are constructed by homeowners on their properties for several purposes. Not only are they incorporated to hide away the unsightly features of a home, but they can also be used to add decorative architectural detail. Soffits construction, on the other hand, is a project that can be done by any DIY person with the knowledge and experience. However, if you lack the confidence to pull this off, then we’d strongly recommend you get in touch with a reliable professional who can guarantee the best results, the first time. In this guide, we’re are going to take you through the soffit construction process.

✓ Measure and mark. The first step is to take an accurate measurement of the size of your propose soffit and use a pencil to mark it out on both the wall and ceiling. The size of your soffits is mainly determined by your needs or preferences.

✓ Cut and Install Wall & Ceiling Plates. Proceed to cut the wall as well as ceiling plates once the dimensions have been marked. Make use of 2x4 lumber, you can cut to size with the help of a table saw or mitre. Once done, you can then attach it to the wall as well as ceiling studs with a framing nail gun.

✓ Build the box frame. Develop a box-frame from 2x4 lumber, using your measurements as guide.

✓ Fit the box frame. Hold the box frame in place with some slide clamps and then attach it to the ceiling and wall plates with drywall screws.

✓ Mark the studs. Make use of a pencil to mark out the studs location on your soffit box frame.

✓ Cut and hang the drywall. Cut the drywall with a utility knife uing your measurement as a guide. Once done, attach the drywall to the framework with the help of drywall screws.

✓ Add finishing touches. This includes installing the corner beads, finishing off with the common drywall work of taping, spackling and sanding. Once the spackle is dry, you can the complete it by painting the soffit.

In the UK, gutters are normally made from uPVC. It’s a hardy plastic that won’t rot, warp or tarnish very easily, which is why it’s so popular. It’s the same material that’s used for most homes’ windows these days; they don’t have to be the standard white as they can be made into a range of colours. Expect to pay an average of £500 for the supply and installation of uPVC guttering, and more if you require scaffolding.

Other materials that are popular for gutters include copper, aluminium and cast iron. These are much more expensive – you might be looking at around £1500 or more for the supply and installation – but they give a more polished look and are often used on period properties or those in a conservation area. If you're considering these types of gutters, make sure you get a few quotes from different roofline companies so you can compare the different materials.

In the past, gutters were made from wood, asbestos concrete or stone. They were often lined with lead to stop the water from seeping through. When it was discovered that asbestos was seriously harmful, it of course stopped being used. Wood was prone to rotting, even with lead lining, and stone is heavy and expensive. So when uPVC came along, it became an affordable and easy material to use for gutters so homeowners could be confident that rainwater will be kept away from the foundations of their properties. It’s important to keep gutters clear from leaves and debris, because if they become blocked, they can make water to fall against your property’s walls, causing damp.

Clean of your conservatory gutter is probably not one of the most enjoyable chores you’d like to take on around the house. Not only is it messy and tedious, but it’s also time consuming and smelly. It’s a job every home and property owner would rather avoid, but unfortunately everyone has to do it. It’s a necessity due to the fact that neglect gutters holds and harbours mould, moss as well as plant debris. It would have been better if this is only disgusting, but the actual truth is that should be the least of your worries as this gradual build up of organic material in your conservatory gutters can minimize their drainage abilities, leading to leakages and spills that can damage your conservatory.

Cleaning of your conservatory gutter is a task that can be done regardless of your level of experience. However, it’s advisable to call in a professional for help especially if you lack the confidence required to pull it off.

• Use a ladder for a closer look. Cleaning your gutters from the ground by poking it with a hooked tool might seem the best way out, but in truth you risk damaging the gutters or brackets and marking the conservatory panes when you don’t see what you’re doing.
• Invest in specialist tools. For expert DIYers, taking off your downpipes from the wall to clean might be a pretty easy task. However, for most people it can be extremely frustrating. As a result, there’s the need to get hold of some flexible gutter brushes. With a bendable stem and stiff bristles, these are able to hook and dislodge dirt and leaves inside your downpipes with relative ease.