Find a Gutter Installer you can trust in Waltham Forest.

Having ventilation in the roof void is a requirement for building regulations approval. Fitting ventilated soffits is the typical way that this roof ventilation is achieved. If you do not have roof ventilation, you may find that your roof void has problems with condensation or overheating.

To keep water away from your house, the importance of gutters cannot be overemphasized. However, in order to enable them do their job the proper way, the clogging dirt and debris must be thoroughly wiped out and fortunately there are a number of ways to get the job done by yourself. However, it must be stated that cleaning of gutters can be a very dangerous task as it deals with working at heights. As a result, if you are not confident enough to this pull this off, then we’d strongly recommend you get in touch with a reliable professional who can guarantee the job effectively and also in a safe manner. In this guide, we’re going to look at some of the ways in which you get rid of dirt and debris on your gutter by yourself.

• Clean the gutter with a leaf blower. Several leaf blowers feature a nozzle attachment which is made to release a narrow stream of air which is suitable for cleaning of gutters. All you have to do is simply to position your ladder to enable you work slowly towards the downspout and getting rid of all dirt and obstructions on the gutter as you go. The final step would be to remove any lingering leaves or twigs using a hose. If don’t want to stand on a ladder to do all these, a specialized attachment is available to add to the blower’s reach.
• Clean the gutter with a wet or dry vacuum. For heavier debris, you can try out a wet or dry vacuum. To reach the obstructed gutters while standing on the ground, simply get curved attachments and hoses at a local home improvement store. You may, however, need to moisten some stubborn dirt before it can be properly vacuumed or removed.after completing the vacuuming process, simply flush the gutters with garden hose waters.

In general uPVC is used for soffits and fascias as it is very strong and durable. It also requires very little maintenance. However, wood can be used and is still popular on listed properties as it retains the original material. Older and listed buildings may require more traditional materials to be used.

It may be shocking a whole lot of people would not be able to point out fascias and soffits on a building despite the fact that they’re an essential part of the roof. To give you an idea, they’re simply used to cover the roof beams’ ends that comes out of the wall from underneath of the roof. The board that runs vertically just below the roofline is the fascia board, which is also the long length of UPVC. Therefore if you look at the gutters located in the front of house, the board behind is called the fascia board. However, soffits runs horizontally from behind the gutters to the wall of a building, so if you walk close to a house and look up, you’ll identify the soffits. They’re done to cover the gaps between the wall house and the gutters. The main function of both soffit and fascia is to divert water away from your roof as well as walls.

Fascias and soffits were usually made of wood before UPVC came along. And as a result, they only require little maintenance, no more warping, painting or cracks unlike the wooden ones. However they also can’t last an eternity, so when the time comes and you need to replace your soffit and fascia, you’ll probably want to know just how much it’s going to cost.

Unfortunately, there’s no way to calculate an accurate cost for fascias and soffits as there are too many variables to put into consideration. These includes the type of fascia and soffit you choose as well as the size of your property. However the average cost to replace a three bed semi-detached house’s fascias and soffits is within the range of £1200 to £1500 or even more if you’re staying in London or in a larger detached building.

Every year, various parts of your roof may need to be changed at one point or the other. Due to the fact that this event can occur at any time in a year, there’s the need to be fully ready. When it comes that being ready, you simply can’t overlook the importance of soffit and fascia boards in protecting your roof space and helping it maintain its clean and unique visual appeal. As a result, when your soffit and fascia boards need to be changed, you best do so as quickly as possible.

This task can be completed by anyone with basic DIY knowledge and experience, but if you lack the confidence to pull off then it’ll be advisable to hire a professional who can guarantee the best results for help.

✓ Remove the old existing boards. In order to install the new soffit and fascia boards, you’d have to remove the existing ones first. If necessary, you can make use of a Stanley knife to make the process much easier.

✓ Fixing soffit boards. Several soffit boards are made using uPVC. The boards are to fixed to the underside of your timber rafter ends. Make sure to use timber to close any gaps between soffit boards and also make sure that your soffit boards’ back are resting against the wall’s top.

✓ Fixing fascia boards. Many fascia boards are also made from uPVC and are usually installed in a similar way to soffit boards. Use a minimum of two nails to make sure they’re secure enough to hold weight of any roof tiles and also to prevent any buckling.

✓ Guttering and felt. To start the guttering, you’d have to screw any brackets into the facia board. You can use a spirit levelto make sure the alignment is perfect to enable the floe of water directly through your guttering system. Once done, you should also check for any rotting roof felt at the edges closest to the gutterin. If there is a rot, make use of eaves felt trays and tuck under existing felt and overlap into the guttering

1. Hang a plumb bob from the outlet to the drain to use as a guide while you draw several marks on the wall with a pencil to show you where the downpipe will run.
2. Join the marks up with a straight edge, creating a line to show where the centre of the downpipe will be.
3. Position a downpipe clip at the top of wall, in the centre of the pencil line. Mark the position of its fixing holes on the wall. If you need an offset bend, put a downpipe clip directly below the bend.
4. Repeat the process down the wall. Make sure there is no more than 1.8 metres between pipe clips.
5. Refer to the guttering manufacturer’s instructions to see which drill bit is required. Use a drill to drill the fixing holes and insert wall plugs.
6. Fit the first piece of downpipe starting from the outlet and moving towards the drain.
7. If you need to add more downpipe, join the two pieces with a pipe socket and clip. Leave a 10mm gap between the end of the pipe and the bottom of the pipe socket, because it will probably expand. Then attach a pipe clip over the joint.
8. Continue attaching pipe clips down the length of the downpipe.
9. If you need to, fit a downpipe show to direct the water into the drain. Attach a downpipe clip directly below the socket of the shoe.

Fascias and Soffits, just like any other components of a home, do not last forever. They can become tired and worn out over time which implies that you’ll have to replace them to prevent further damage. Getting this project completed can be quite costly, but it doesn’t have to be. Fitting soffits and fascias is very simple task which will leave you with both a modern and contemporary styling which requires little maintenance and also more savings. What’s more? You don’t have to worry about repainting the fascias and soffits on an annual basis, all you need to do is a gentle wipe down of the features with a damp cloth to have them look good.

If you’re a competent DIYer and confident enough to pull off this task, then all the better. However, if otherwise, we’d strongly recommend you hire the services of a reliable contractor who can guarantee the best results for help. Here are the steps you can follow to fit your fascias and soffits.

Fascias ( a 18mm fascia board)

✓ This is designed for a direct fix without a need for a timber substrate. Simply secure them directly to the rafters with the help of 2 x 65mm a4 stainless steel fixing nails per rafter.

✓ Ensure that the rafters are level.

✓ Cut the boards back 5mm per edge to enable expansion where any white corner trims, joint trims or angle trims is needed.

✓ Secure the guttering to all third rafter.

Soffit ( 9mm soffit board)

✓ Ensure that the preservative treatment to the structural timber has dried out.

✓ Fix all utility boards of about 100mm to 605mm in width at a maximum of 60mm centres.

✓ If ventilation is needed, there are some soffits that are available in 150mm to 605mm widths and also provides the 10mm air gap needed for roof with a pitch above 15 degrees

Knowing when best to clean your gutters can do a lot of good. Wile some people assume that fall is the best time for gutter cleaning after the leaves fall, others believe spring is the most appropriate time to clean the gutters before things start to grow there. The truth is, both camps are right. However, the best time to clean your gutters depend on a wide range of factors which are all unique to you. In order to help you make the most informed decision possible, we have created this post to help you figure out the right time to clean your gutters. Let’s take a look!

Where you’re located. What we get is four season in a year as well as as a good amount of rain. As a result, you may want to put into consideration cleaning your gutter at least twice a year - clean the gutters once in the spring and once in the fall. It’s important to make gutter cleaning a part of your normal spring schedule as well as part of your fall maintenance routines.

What surrounds your home. If you happen to have tree surrounding your home, then it’s more likely that dead leaves clog up your gutter pretty quickly. A single tree is enough as it’s going to shed leaves that will find their way into your gutter, accumulate and affect its performance and integrity.

What your gutter currently looks like. If you gutters already have an entire ecosystem of animal life and plants hamging over the edges, then the best time to clean the gutters is now rather than having to wait a particular season to act. A dirty gutter should be attended to immediately in order to prevent some unnecessary damages as well as expensive repairs.