Find a Gutter Installer you can trust in Bruton.

You don’t always need to replace your gutters with your roof. Often people think that it’s a requirement, or simply the best thing to do, but it’s not always necessary. The reason why people think it’s required is because to re-roof a home, the guttering often needs to be removed and put back on.

If the time has come to replace your roof, then the chances are that your guttering is pretty old too. When you start to get quotes for your roof replacement, ask the roofer to take a look at your guttering as well. If there are signs of peeling, rust, cracks or sagging, then it makes sense to replace your gutters with your roof. If you get them done at the same time, you’ll save money labour costs, which is the reason why most homeowners do it.

Another reason to replace your gutters with your roof is the risk of damage. Re-roofing is a significant project, so the guttering needs to come off most of the time – running the risk of brackets and pipes getting damaged in the process. So if your guttering is still looking good right now but you think it might need replacing in a couple of years, it might be worth just doing it at the same time as your roof to save you money and the stress if damage does occur.

However, if your guttering has only recently been replaced, then there’s no need to replace it again with your roof. But because it needs to come off, make sure you speak to the roofing company about keeping it safe and doing their best to avoid damage. It’s also worse ensuring that they have the correct insurance to cover you both in case your guttering does get damaged during your roof replacement.

Soffits and fascias sit along the sides of your property, over the join between your walls and your roof. The fascia attaches to the end of your roof rafters, hiding and protecting them. The soffit fixes on the bottom of the fascia, bridging the gap between your fascia and wall. Your guttering attaches to the fascia, which also joins to the bargeboard on your gable end, if you have one.

It may be shocking a whole lot of people would not be able to point out fascias and soffits on a building despite the fact that they’re an essential part of the roof. To give you an idea, they’re simply used to cover the roof beams’ ends that comes out of the wall from underneath of the roof. The board that runs vertically just below the roofline is the fascia board, which is also the long length of UPVC. Therefore if you look at the gutters located in the front of house, the board behind is called the fascia board. However, soffits runs horizontally from behind the gutters to the wall of a building, so if you walk close to a house and look up, you’ll identify the soffits. They’re done to cover the gaps between the wall house and the gutters. The main function of both soffit and fascia is to divert water away from your roof as well as walls.

Fascias and soffits were usually made of wood before UPVC came along. And as a result, they only require little maintenance, no more warping, painting or cracks unlike the wooden ones. However they also can’t last an eternity, so when the time comes and you need to replace your soffit and fascia, you’ll probably want to know just how much it’s going to cost.

Unfortunately, there’s no way to calculate an accurate cost for fascias and soffits as there are too many variables to put into consideration. These includes the type of fascia and soffit you choose as well as the size of your property. However the average cost to replace a three bed semi-detached house’s fascias and soffits is within the range of £1200 to £1500 or even more if you’re staying in London or in a larger detached building.

• A sturdy ladder
• Gloves and safety goggles
• A hammer and nails to secure your fascia so it doesn’t fall down mid-replacement
• A hacksaw – this will cut through uPVC guttering – just make sure you leave a margin of error with every cut you make
• Cable ties or rope to secure the existing gutters while you dismantle them, so they don’t fall off
• All the right fixings and brackets to secure the guttering
• An electric drill and/or screwdrivers

1. Add a gutter bracket to the top of the fascia board at the opposite end to the stop-end outlet, if you have one. Then tie a piece of string around the base of the bracket.
2. You’ll need to place the gutter outlet accurately over the drain. Hold a plumb line against the fascia directly over the drain, and mark that position with a pencil. Following the manufacturer’s advice on the number of screws to use, fit the gutter outlet no more than 50mm below the level of the roof tiles.
3. Stretch the piece of string you tied on the bracket along the fascia board, and tie it to the outlet. Make sure you check with a spirit level that the string slopes towards the outlet.
4. Mark the positions of the other brackets. They should be no more than 800mm apart, or 600mm if your roof is very steep. They also shouldn’t be any more than 150mm from a joint or fitting. Then fit the rest of the brackets.
5. Fit a stop-end to the first length of gutter and clip it into position on the brackets. At the other end, fit a union piece and screw it into the fascia.
6. Then fit the next length of gutter into it, and the next until you’re finished. Cut the last one to fit using your hacksaw before attaching a stop-end. Then make sure all the joints line up with the insertion depth marks on the fittings. Then you’re done!

It can be a huge headache, but cleaning of gutters is a task that needs to be done and even more so when it’s a stained white gutter. Nobody want to do it, but everybody has to. If you happen to lack the required confidence to pull this off as it has to do with working at heights, then we’d strongly recommend that you get in touch with a reliable professional who can guarantee the best results for help and also save you some time and money from potential costly errors. In this post, we’re going to show you some of effective way in which you can tackle stained white gutters effectively.

Firstly, you’ll have to take out the ladder with a pair of rubber gloves. Simply position the ladder safely, climb up the roof and start removing the leaves and other debris clogging up the gutters. You can also make use of a garden trowel to remove the very thick debris. Once done, spray the gutter using a garden hose to flush out the dirt as this will make the stains visible. Then prior to cleaning, ensure to cover the plants or landscape underneath with tarp or plastic sheet since the cleaning solution may negatively impact the vegetation.

Start to clean by spraying an all-purpose cleaner on the stains and srub them off using a scrub brush. You can also try a mixture of 1/4 of water with 1 cup of bleach and 1 teaspoon of dish soap. Dip your scrub brush in this solution to scrub off the stains. The bleach mixture is guaranteed to eliminate any mold or mildew that growing on your gutters with ease.

In general uPVC is used for soffits and fascias as it is very strong and durable. It also requires very little maintenance. However, wood can be used and is still popular on listed properties as it retains the original material. Older and listed buildings may require more traditional materials to be used.

A gutter is part of the system that takes rainwater away from a building. Every home will have some form of guttering system to stop water from dripping off the roof and into the walls. It’s important to keep your gutters clear because if water starts to seep into your home’s walls, you’re likely to get damp.

A guttering system consists of half pipes, troughs, bends and downpipes. They’re usually cylindrical in shape but they may be square on some homes and in countries outside of the UK. Technically, the gutter is the part that you’ll see across your roof that collects rainwater. The water will then feed into a downpipe from your roof’s edge to the base of your home, where you can collect it in something like a water butt, or it will be discharged to a surface water drain or soakaway.

In early times, gutters used to be made from lined wood or stone. Lead was often used as the liner to stop rainwater from seeping through the material, but you won’t see it used much anymore. These days, most homes have uPVC guttering as it’s a hardwearing plastic that should last a long time. But you’ll also see gutters made from aluminium, cast iron and copper, especially on period homes or those in a conservation area.

Every home needs a guttering system to ensure that rainwater doesn’t affect the foundations of the property. It’s also important to keep the gutters clear of debris like fallen leaves, as this will cause them to overflow, potentially causing water to soak into the walls and causing damp.