Find a Handyman you can trust in Haverfordwest.

There are a bunch of things a handyman can do around the house, so if you’re looking for a reason to hire one, you’d definitely find plenty. First and foremost, a handyman is basically a well versed, skilled and experienced professional who possesses the ability to carry out a plethora of tasks as well as repairs. While not all local authorities require handymen to have a license or carry an insurance policy, some handymen do have insurance. Generally, their rates vary based on their experience as well as specialities.

Handymen are able to handle a multitude of potential jobs in and around the house. These ranges from small tasks, installations, assembly, indoor or outdoor building or repair jobs. They are available to help out with a wide array of odd jobs around the home at a very reasonable price. So, what are some of the jobs a handyman can do in a home? Let’s take a look!

• Odd jobs. This encapsulates any small job you’d want done around the house. It could be a repair, installation or maintenance task.
• Gutter cleaning and repair. The idea of cleaning a gutter may seem hassle free, but there can be a couple of difficulties which includes the use of ladders and the risk of falling. When you hire a handyman to do this task, he does not only clean but also check for any damage or repair needs and much more.
• Painting. If you’re not able to handle some of your painting projects or perhaps you’re just not confident of how its going to turn out, it may be in your best interest to reach out to a skilled handyman.
• General carpentry and home repairs, these includes shelving, cabinets, bookcases, baseboards, framing, doors, countertops, moulding and more.

1. Mark out the area and dig the top layer of soil, trying to get the ground as flat as possible.
2. Build a timber frame to size.
3. Measure out 4 rows of 3 blocks to create good weight distribution and lay in place.
4. Underneath each block, dig around 50mm wider than the blocks and about 150mm deep. Fill the hole with pea gravel until it’s flat.
5. Place timber planks along the rows of blocks and see how level it is. Add or remove blocks where necessary. If it’s only a small difference, use shingle underneath the timber until it’s level.
6. Nail your timber shed base to the timber planks to create a sturdy base for your shed.

There is a variety of methods available to ensure that your paving drains properly, for example draining into a lawn or soakaway. Correct drainage of paving is a requirement for planning permission. See our guide on planning permission for paving for more information.

You should always wait until plaster is dry before painting. The time this will take varies depending on the room and property, but in general, it will take about a week. Your plasterer will tell you how long it is best to leave it before covering or painting their work.

How To Clean A Roof?

If you’re planning to clean your roof, but don’t know where to start, you’ve come to the right place! There are different types of roofs available in the market today and the method used in cleaning one can be largely different from the other. As a result, we’re only going to look at one of the common types of roofs you’ll find in the UK - the Asphalt shingle roof tiles. This roof type is very common and for a good reason. Not only are they visually appealing but they’re also hugely versatile by design which enables them to be adaptable to varying shapes, angles as well as forms depending on your preference or needs. With all the benefits that can be derived from asphalt shingle, they however, need to be properly maintained to help retain their good looks.

To clean your asphalt shingles, you’ll most likely require some type of chemicals especially when dealing with algae stains and some other visual problems. Therefore, make sure you purchase a product marked safe to be used on this type of roof and not those only proven to remove moss and algae stains. Mix the chemical cleaner with a gallon of water and a quart of bleach or as instructed by the manufacturer. Pour the mixture inside a pump-style garden sprayer and mix thoroughly. When done, climb up on the roof and spray as good as you can. Upon completion of spraying the roof with the mixture, then allow to work its magic for some time - about 15 minutes or thereabout should be good.

After that, you can make use of a garden hose to spray down the roof and wash down the mixture entirely. If some stains remain, use a brush to gently wipe the tiles individually.

a typical rate would be around ₤ 300 for suitable kitchen doors just from a local company, or up to ₤ 1200 from a large National supplier.

1. Plan your shed base You must have a sturdy base for your shed, otherwise the frame won’t stand properly and could stop the door from opening. Decide whether you’re going to have:
   • A concrete base laid on hardcore
   • Concrete slabs on sharp sand
   • Treated wood beams on hardcore or shingle
   • An interlocking plastic system
   All bases should be laid on firm, level ground as far as possible.
2. Treat wood with preservative To help your shed last as long as possible, you should coat all the wooden parts with timber preservative before you put it together.
3. Put the shed floor together Some will need more assembly than others, but you need to make sure that the floor panel is attached to the joists; follow the manufacturer’s instructions for the correct spacing.
4. Put up the shed walls
   • Mark the centre point of each wall on its bottom edge, then do the same for the shed floor so you can line them up together.
   • Stand the gable end on the base and line it up. Check that it’s vertical with a spirit level – you might need someone to support the panel while you do this. Use a temporary holding batten to keep it in place.
   • Fix a side panel to the gable end panel with countersunk screws, then add the second side panel in the same way.
   Don’t attach the panels to the floor until you’ve fitted your shed roof.
5. Fit the roof
   • If the shed comes with a support bar, put this in position before you put the roof panels in.
   • Nail the roof panels in place, ensuring there’s a parallel and equal overlap at each end.
   • Roll out some roofing felt from front to back, leaving a 50mm overlap at each side. Secure it with clout-headed felt tacks at 100mm intervals.
   • Apply mastic sealant to the outside corners, then fix each corner trim with 30mm nails.
   • Add the fascias and finials, predrilling 2mm holes to avoid splitting the wood. Nail them through the felt into the shed using 40mm nails.
6. Add the shed windows
   • Slide each windowsill into the tongue and groove cut out, then put the window cover strip in position, fixing it to the vertical framing.
   • From inside the shed, put the glazing sheets into the window rebates, making sure the bottom edge of the glazing sheets sit on the outside of the sill.
   • Fix the window beading on the top and sides with 25mm nails.
7. Fix the walls to the floor Before you do anything, make sure you check that the centre marks on the walls line up with the marks on the shed floor. Then fix the wall panels to the floor with 50mm screws, aligning them with the joists.
And that’s it! But if you’re not confident in building a shed yourself, there are plenty of professionals available who will be happy to help.

Fitted wardrobes are the best choice of wardrobe for most households and they’re a popular option for several homeowners for a good reason. Not only are they able to efficiently maximize your space and fit into any space no matter how awkward, but they can also be customized to fit your personal needs to feature custom lighting and many more. So if you’re planning to have one fitted but on a tight budget, you’d probably be wondering how you can install a fitted wardrobe in an alcove by yourself. This is a relatively easy task if you’re attentive to the details, however, if you’re not confident enough to pull this off, we’d advise that you get in touch with a professional who can guarantee the best results for help.

To construct a fitted wardrobe in an alcove, simply follow these steps:

✓ Take a measurement of the available space including the length, breadth and width.

✓ Sketch out what you want the wardrobe to look like while also staying within the measurements. Here, you’ll have to be particular about everything like the drawers, shelves etc.

✓ Build the frames upon which every other construction would be made.

✓ Attach the frames to the wall and floor. Make use of a hammer drill with a masonry bit to drill the holes if its a concrete floor.

✓ At this stage, you’ll have to start building your shelves in accordance to the number you’ll need.

✓ Based on the design in step 2 above, you’ll have to add the door at this stage. This is however optional as some homeowners prefer door-less wardrobes.

✓ The final step is to paint the the finished wardrobe to your taste with your choice of colour.