Find a Heating Engineer you can trust in Angus.

How Much Does A Boiler Repair Cost?

An annual service for your boiler might not seem important and may be easy to postpone to another day, but when it happens to breakdown due to lack of adequate attention, this can be quite painful and also costly.

Before you start thinking about the cost of repairing your boiler, the first thing you’ll need to confirm is whether or not your boiler is still covered by the manufacturer’s warranty. You’d be amazed some warranties can last for as long as 12 years, if yours is still on then you can save yourself a huge amount of of money on your boiler repair. As a result, it’s always crucial to keep the details of your warranty somewhere safe, so you can read them from time to time. You never can tell when the rainy day will come!

Most boiler warranties will require your to get your boiler serviced on an annual basis by a licensed and qualified technician. The cost of an annual boiler service is affected by the time of the year you wish to get it done. When boilers are less useful during the summer months, an annual service is usually relatively cheap when compared to the cold months. Around this period, a boiler service will normally cost within the range of £100 to £150, however for a more accurate quote it’s advisable to contact a couple of professionals and compare their quotes.

The cost of getting a boiler repaired will be affected by a couple of factors including your boiler’s make, the age of the boiler as well as your location and how urgent you need it done. If you have a dead boiler, the cost will typically range from £96 to £348 and a boiler displaying a fault code will cost within the range of £90 to £275. Generally, repairing a boiler will cost within the range of £90 to £400 based on the several factors stated above.

Your LPG storage tank will need to go outside your property, possibly underground if you have limited space. There are planning rules that restrict where you can put your tank, especially if your property is listed or on designated land. Take a look at our planning permission article to find out more.

How To Fix A Broken Boiler

To fix any problem when it comes to home appliances, the first step is always to identify the problem while also carrying out thorough checks - a broken boiler is not an exception. Putting enough time and effort in diagnosing a problem can go a lot way to save you both time and money. So here are some of the steps you can take to fix your broken boiler before you put a call out to a licensed engineer.

✓ Check to confirm if your pilot light is on. Whenever you’re facing some issues with your boiler, this should always be the first thing you do. The pilot light being on speak volumes, if the light is off then there’s absolutely no way the flame can start the appliance’s gas supply. You should try to put it back on, if off. To do this, you simply have to follow the detailed instructions on your boiler’s manual strictly. If after following these actions to the letter and the issue remains the same, then you’d probably need the services of an a qualified engineer. Never try to fix the issue on your own.

✓ Check the pressure. The solution to the headaches might sometimes be as simple as examining your appliance’s pressure gauge. Here, the good numbers are around 1.0 or1.5, if it happens to fall below this, then you should open the boiler’s instruction manual. You can also inspect your radiator valves for any leaks. You’d have to call in a specialist to solve the issue.

✓ Check the thermostat. Here, it’s important to note that a faulty thermostat doesn’t necessarily imply a broken boiler. It may just signify that you need to replace your thermostat. Simply check to ensure that your thermostat is turned on and temperature is at the appropriate degree.

How Do Electric Boilers Work?

Electric boiler are installed in residential, commercial and industrial properties to serve as a reliable source of heat. Unlike other types of boilers that depends on fossil fuel burning to be able to operate, electric boilers are fuelled by electrical energy which ultimately makes it more reliable and powerful compared to its counterparts. This heating option was basically provided for home or property owners who don’t have an access to the main gas supply.

So how does an electric boiler work? Basically, an electric boiler work by heating water. Once heated, the hot water supply is then distributed to various areas across the house or property. In order to achieve the best possible efficiency at the lowest possible costs, new model electric boilers are installed by licensed and professional boiler fitters with the help of a microchip control system. Meanwhile, the microchip control system functions to oversee the management of both temperature level as well as output.

Unlike other types of boilers such as a gas boiler, electric boilers only require minimal service. If you own a gas boiler, it’s crucial to ensure that it’s serviced every single year by a licensed and reliable professional that’s into boiler repair services. During the checks and maintenance services, the gas boilers would need to be checked for possible gas leaks, as well as ventilation poisoning and other problems.

Overall, electric boilers are considered to be one of the most environment-friendly heating system which is more affordable to install in your property than a gas boiler. It represents the most ideal option for homes with gas boiler issues as well as those that are not connected to the main gas supply. What’s more? Electric boilers are also one of the best options for wet central heating and under floor heating.

How To Install An Oil Boiler Heating System

Just like several other skills, the installation of an oil boiler heating system can be a challenge. It requires enough persistence to actually get right, so if you’re the type with little patience, we’d recommend you hire the services of a professional oil boiler heating system fitter who can guarantee the best results and save you time and extra money due to potential damages.

To install your boiler system yourself, it’s always advisable to start by getting the information on the best installation processes from the supplying company which will go a long way to save you from future headaches. However, we’ve put together this guide to give you a basic knowledge on how its done. Let’s have a look!

lRead Instruction Manual

• Carefully read and digest the instruction manual thoroughly.

• Make sure you understand the installation diagrams

• Spread out the materials and get familiar with them.

lFigure Out What Goes Where

• Take your time to determine where everything goes in relation to the others.

• Identify the new radiator’s position.

• Get sufficient sealants to prevent possible leakages inside the walls.

lIdentify The Pipe Routes

• Determine the pipe routes while fitting the new radiators

lInstall The Boiler

• Turn off water and all electrics

• Fit the boiler into the wall

• Make sure the fittings are secured.

lInstall The Radiator

• The effectiveness of your home’s heating system is as good as the radiators you incorporate and how good they’re installed.

• You may have to utilize extra radiators in large open plan kitchens and living rooms (for effective heating).

lOffer Ventilation

• Once you’ve successfully installed the new radiator, a small dose of air ventilation would be needed.

• Turn the key of each valve located at the bottom, do not stop until a little amount of water spills over the top of the unit.

Do British Gas Service Oil Boilers?

Are you interested in finding out whether or not the British Gas service oil boilers? Well, you’ll find the answer in this article! The British Gas engineers are able to repair several types of boilers such as home based combi, conventional as well as system boilers. Unfortunately, they do not fix oil boilers, electric boilers or solid fuel boilers, but if you possess a gas boiler that’s more than 70kW which is mostly present in commercial premises or large buildings you can give them a call.

For a yearly boiler service British Gas engineers will provide the following solutions to ensure central heating and boiler are both in proper working condition and also absolutely safe.

• Inspection of your boiler for possible leaks and corrosion.

• Detach your boiler casing to ascertain the proper functioning of it’s main components.

• Clean up all parts as necessary

• Attach the casing back to the system and make sure its well sealed

• Inspect the level of the gas pressure to ensure that it’s at the right level.

• Perform a flue check to determine that the are no toxic gas emissions like carbon monoxide being discharged by your heating system.

Upon completion of the annual boiler service, the British Gas qualified engineers will then drop a checklist with you which is going to include all the relevant information you may want to know about your boiler system.

In some cases, British Gas engineers may be able to complete the entire boiler service in one visit. However, it all depends on the problem that’s discovered (if any). They may not possess the required part to fix the problem with them, so they’ll have to order it from the British Gas national distribution centre. Most times, this part will get to them the next day so they can finish their tasks as soon as possible.

If you’re interested in deriving maximum benefits from your central heating system while also being a tech-enthusiast, a smart thermostat is just the perfect option as it allows you to control both your boiler and heating system via your mobile device. It also offers a plethora of features which enables you to heat your home more efficiently while also cutting your energy bills. Here, we’ll be taking a deeper look at the Tado smart thermostat (a user friendly smart thermostat with multiple impressive features such as a great design, self learning and LED interface).

A Tado smart thermostat is a relatively small piece of kit which is perfect for tech-lovers looking to get a first experience of the smart thermostats’ world. Although the appliance might feature just a basic design with a bit less advanced features in comparison with other thermostats like Hive, Nest and more, it however, still comes with some fantastic features which you can’t afford to miss out on. These includes geofencing, Smartphone or tablet control as well as heat scheduling. As you would have expected with any good smart thermostat, the ability to remotely control your heating is a top priority for several smart thermostats’ owners and Tado offers you this and more. Therefore, no more worries during the Winter months and wishing your home should be warm and perfect for your return. Aside this, a Tado smart thermostat also goes a long way to ensure efficient energy use and as a result, reducing the money paid on energy bills.

Overall, Tado is a nicely designed smart thermostat which is relatively easy to use and a perfect option for homeowners interested in having a taste of the world of smart thermostats or looking to replace their existing device.

How Long Does A Boiler Service Take?

Servicing of your boiler is a very crucial activity which does not only help in keeping your heating system in a top condition, but also assists in ensuring the safety of both you and your loved ones. If you carry out a regular boiler service you’ll be able to identify any possible fault your boiler may have on time before it leads to a more serious issue or even a boiler breakdown. As a result, you’ll be able to save yourself some time and money, but more importantly will save you from any dangerous risk that may result from gas leak in a boiler. The best time for a boiler service is in the summer when you’d probably would not really need the system, so you can take advantage of that as well as the possible lower boiler servicing cost during this period.

Before we look into the amount of time a boiler service should take, let’s first consider what should be done during a boiler service.

✓ Visual inspection. This is a check carried out by the heating engineer to ensure your boiler still meet the existing standards and requirements while also looking for any faults.

✓ Removal of boiler casing. There’s the need to ensure everything is working just fine and also to clean the boiler’s interior. These inspections should include the burner, heat exchanger, main injector and spark probe.

✓ Flue check. This involves making sure that there’s no form of obstructions in the flue terminals as also to ensure that the flue is well installed.

✓ Gas pressure check. This involves making sure that the boiler working with the appropriate pressure.

✓ Boiler fired up. This involves checking for any operating issues.

Generally, a boiler service should be completed within 30 minutes, however this time may vary largely depending on the brand and model.