Find a Heating Engineer you can trust in Keith.

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.

If your boiler is making strange noises or smells, or doesn’t seem to be working properly, it may need replacing. Boilers usually last about 10-15 years. Even if your boiler is working normally, it’s worth replacing when it gets this old. An annual check will establish if there are terminal problems with a boiler that cannot be fixed.

How Often To Service Boiler?

A boiler is a vital part of any home especially if you’re in the UK. Not only does provide your entire household with hot water and keep them warm but also adds a good value to your property. Boiler repairs and replacement are both super expensive and stressful, so in order to avoid all these worries, it’s better to have your boiler serviced on a regular basis for your own peace of mind. When you call in a reliable heating engineer, it can immensely raise your boiler’s efficiency while also saving you from more expensive issues down the road.

So if you haven’t had your boiler serviced for quite some time, moved into a new house and not aware the last time your boiler was serviced or perhaps you’re just wondering how often a boiler should be serviced, then you’ve come to the right place! The short and simple answer to this question is a boiler should should be serviced once in a year, and most preferably during the summer months. However, there are a wide range of factors that comes into play so it’s always advisable to check with your manufacturer before you proceed.

According to the law, you’re required to have your boiler services on an annual basis. Failure to do so can render your boiler or home warranty void. Therefore, it’s very crucial to take down the last time your boiler was serviced and also set a reminder to book your next appointment when the time closes in.

If you happen to own an electric boiler you may not need an annual servicing. But you may still be required to perform it annually by your insurance provider.

How Much Is A Landlord Gas Certificate?

Do you know as a landlord in the UK, not only does the law requires you to conduct an annual check on all your gas appliances and chimney, but you’d also have to pay for it? Hence, giving birth to the commonly asked question, how much is a landlord gas certificate? With so many variances in CP12 certificate prices everywhere, it can be so confusing knowing the actual one you’re expected to pay. Just by surfing the internet alone you’d come across loads of ads claiming they can help you with a cheap gas safety certificate only to discover that reverse is the case when you reach out to them. Here, you’ll get to know the real amount you’re expected to pay for the annual checks on your gas appliances and chimney.

First and foremost, let’s look at what a Gas Safety Certificate really is. This is a certificate that’s given out to landlords and property management companies after a check has been carried out on all their gas appliances and chimney. This statutory check is expected to be done every 12 months to ensure the safety of all those who make ue of your rental property. Homeowners living in ther property are not required by the law to conduct annual gas safety check, but it’s highly recommended that you get in touch with a Gas Safety engineer to ensure the safety of both you and your loved ones.

As a landlord in the UK, to get all your gas appliances and chimney inspected by an approved Gas Safety engineer and obtain your Gas Safety Certificate, you’re expected to pay within a range of £55 to £65. However, you should note that this cost will increase depending on the number of gas appliances you have (about 30% increase for each additional gas appliance).

How Does Electric Central Heating Work?

An electric central heating works to provide a number of benefits for you. These benefits include the following:

lSpace Heating

• The storage heaters work during the night to store electricity which would be used to heat up the heat retaining bricks. This, in turn, will release this energy throughout the day to warm up the room.

• There are also electric radiators which works to deliver on-demand heat and as a result, economy tariffs are totally avoided. It will generate heat by itself rather than storing it and with the controls, you can easily determine the amount of heat to be released when you require it.

• There is the wet electric system options as well which comes with water filled radiators. This operates in a similar way to normal radiators, however, it makes use of electricity to heat up the water.

lWater Heating

• An electric boiler operates in a very similar manner to other boiler types, just that it makes use of electricity as its fuel. Here, the water is warmed by a heating element and the water is later moved to several radiator throughout the house by a pump. These electric boiler types earns you tariff savings as you’ll be able to heat water at night.

• Heat pumps geothermal or air source, redistributes heat instead of creating it. Heat pumps are powered by electricity and it works by absorbing heat either from the air or ground which it then channels it through a pump. This can then be incorporated in heating either water or a room.

• A dedicated immersion heater is another water heating option. Here, the heating element is positioned inside a hot water cylinder. In a similar fashion to a kettle, the element heats the nearby water. Immersion heater can act either as a backup or your main heating element.

How Long Does A Gas Safety Certificate Last?

As a result of faulty installation and irregular maintenance of gas appliances and chimneys, a lot of people have been met with an untimely death caused by the toxic gas - carbon monoxide. This is a gas that’s completely odourless, colourless and tasteless - meaning you can’t identify one of its in the environment. But what you should know is, if you stay in an environment filled with carbon monoxide, you’d probably be dead within a couple of hours. Consequently as a landlord, you must do what’s best to ensure the safety of all your tenants by making sure that all your gas appliances and chimneys are subjected to annual check by an approved Gas Safe engineer as required by the law.

Wondering how long a Gas Safety Check will take? The safety of your gas is guaranteed by carrying out regular examinations. Whether or not you possess a gas alarm, it’s still vital to conduct regular gas safe checks to make sure your home is safe. A typical gas safe check would last between 30 to 60 minutes for a normal domestic property. However, in the situations whereby a need for repair arises, it may take longer time to complete. Other factors that can also affect the timing includes includes both the size and location of your property.

So how long does a gas safety certificate last? The simple answer to this question is 12 months. If you own a rental property in the UK, it’s up to you to ensure all your gas appliances and chimney is check after every 12 months to obtain a Gas Safety Certificate which you should hand out a copy to all tenants living in your property. However, if you don’t own the property, you can inform your landlord to get one as soon as possible while also providing a carbon monoxide alarm.

How To Make Oil Boiler More Efficient?

During the winter months when the nights get darker and colder, it’s more likely your oil gets used up a lot more quickly. This can be very worrisome as it implies having to spend more money to refill. So what exactly can be done to make your oil boiler more efficient and save you some money?

• Regular Servicing Of Your Oil Boiler

Getting your boiler serviced by a manufacturer approved engineer on an annual basis is one of the easiest and quickest ways to ensure that your oil boiler is operating at its maximum efficiency level. When a full servicing is provided for your oil boiler, checks are made to ensure that all components are functioning the way they should while also identifying the bad or worn parts that may be hindering your oil boiler from functioning in an effective manner. As a result, it helps you see to the fact that your boiler is not consuming more than necessary to make sure your oil boiler lasts longer.

• Set Your Thermostats Correctly

When you set your room thermostats and thermostatic radiator valves (TRVs) the right way, you’ll be sure to get a comfortable home without having to make use of much fuel.

• Consider Smart Technology

If you decide to make use of smart technology like Nest or Hive, you can save more money when compared to their more conventional counterparts. These smart technologies incorporate highly advance intelligent systems to get more familiar with your lifestyle, habits as well as heating operations in order to ensure optimum efficiency at all times.

• Put Your Radiators To Good Use

Try as much as possible to avoid some oversights that can make your radiators consume more energy than required. Consequently, you have to keep them clean, give them space and also take care with curtains.

In recent times, home and property owners are constantly looking for ways in which to enhance both energy efficiency and sustainability especially as the world draws closer and closer to energy-efficient technology. The Nest thermostat is a great example of this fact as its designed in such a way to save energy while also cutting heating and cooling costs. And an interesting fact is, you’re not limited to using just a single Nest thermostat in your home as multiple of the device can successfully run together to maintain a consistent level of temperature monitoring as well as energy efficiency. What’s more? You can add up to 20 Nest thermostat and 18 temperature sensors in a home.

It’s very unlikely that you’re going to need this many thermostats in your home, but if you’d like to add a second the process is quite straightforward. However, we’d recommend you employ the services of a seasoned professional especially if you lack the required training or experience to pull this off to save yourself some time and money.

To get started, simply download the associated Nest app to add Nest devices. Now let’s have a look at the processes involved in adding a second Nest thermostat to your home.

• Open the app.

• Go to the top left corner of the main screen and click on the menu button.

• Pick the location or home you’re adding the device to.

• Go to the top right corner and select the “settings.

• Once done, then click on the Add Product “Plus button.

Upon a successful addition of the second thermostat, the app will guide you through the initial set up steps. Google also offers a very helpful guide if you’re unfamiliar with the initial configuration.