Find a Heating Engineer you can trust in Cockburnspath.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

• Switch off your boiler and let it cool completely

• Make sure both ends of your filling loop are attached

• Open both valves to allow cold water into the system – you’ll hear it start to move

• Look out for your pressure gauge to show 1.5 bar

• Close both valves

• Switch your boiler back on

• Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

How To Install An Oil Boiler Heating System

Just like several other skills, the installation of an oil boiler heating system can be a challenge. It requires enough persistence to actually get right, so if you’re the type with little patience, we’d recommend you hire the services of a professional oil boiler heating system fitter who can guarantee the best results and save you time and extra money due to potential damages.

To install your boiler system yourself, it’s always advisable to start by getting the information on the best installation processes from the supplying company which will go a long way to save you from future headaches. However, we’ve put together this guide to give you a basic knowledge on how its done. Let’s have a look!

lRead Instruction Manual

• Carefully read and digest the instruction manual thoroughly.

• Make sure you understand the installation diagrams

• Spread out the materials and get familiar with them.

lFigure Out What Goes Where

• Take your time to determine where everything goes in relation to the others.

• Identify the new radiator’s position.

• Get sufficient sealants to prevent possible leakages inside the walls.

lIdentify The Pipe Routes

• Determine the pipe routes while fitting the new radiators

lInstall The Boiler

• Turn off water and all electrics

• Fit the boiler into the wall

• Make sure the fittings are secured.

lInstall The Radiator

• The effectiveness of your home’s heating system is as good as the radiators you incorporate and how good they’re installed.

• You may have to utilize extra radiators in large open plan kitchens and living rooms (for effective heating).

lOffer Ventilation

• Once you’ve successfully installed the new radiator, a small dose of air ventilation would be needed.

• Turn the key of each valve located at the bottom, do not stop until a little amount of water spills over the top of the unit.

If you’re interested in deriving maximum benefits from your central heating system while also being a tech-enthusiast, a smart thermostat is just the perfect option as it allows you to control both your boiler and heating system via your mobile device. It also offers a plethora of features which enables you to heat your home more efficiently while also cutting your energy bills. Here, we’ll be taking a deeper look at the Tado smart thermostat (a user friendly smart thermostat with multiple impressive features such as a great design, self learning and LED interface).

A Tado smart thermostat is a relatively small piece of kit which is perfect for tech-lovers looking to get a first experience of the smart thermostats’ world. Although the appliance might feature just a basic design with a bit less advanced features in comparison with other thermostats like Hive, Nest and more, it however, still comes with some fantastic features which you can’t afford to miss out on. These includes geofencing, Smartphone or tablet control as well as heat scheduling. As you would have expected with any good smart thermostat, the ability to remotely control your heating is a top priority for several smart thermostats’ owners and Tado offers you this and more. Therefore, no more worries during the Winter months and wishing your home should be warm and perfect for your return. Aside this, a Tado smart thermostat also goes a long way to ensure efficient energy use and as a result, reducing the money paid on energy bills.

Overall, Tado is a nicely designed smart thermostat which is relatively easy to use and a perfect option for homeowners interested in having a taste of the world of smart thermostats or looking to replace their existing device.

Ad hoc visits from your engineer to fix small issues with your heating system may actually seem cheaper and a lot more affordable, however when a boiler is ripe enough for a change these small issues are always never ending. Over some period of time, these small issues will inevitably get worse and the idea of “mend and make do will be an absolutely false economy. The best course of action in this sort of event is to find a replacement boiler to install as soon as possible. In this article, we’re going to give you some hints that’ll show you when your boiler needs to be replaced. Now let’s take a look!

✓ Insufficient hot water. Here, you’ll have to check the size of your hot water cylinder. It’s crucial to make sure that your boiler is rightly sized to power your heating as well as hot water circuit in line with your demands. You should always seek the advice of a heating expert who can recommend whether to fix or replace the boiler.

✓ Strange noises. It’s normal for components of the boiler to become worn or damaged over time. Replacing the particular component that’s causing the knocking or rattling may seem cost effective at first but more often than not, the noises usually signal a bigger issue which is likely to build up over time. Hence, it’ll be a lot more logical to replace the boiler itself.

✓ Regular repair of your boiler. It’s essential to have your heating system serviced by a Gas Safe engineer on an annual basis. However, when you have to call them more often than once a year for your yearly maintenance, it may be a wise decision to consider getting a replacement.

✓ Other events whereby you may need a new boiler includes when you can’t get the right temperature in your room, when the radiators don’t heat up as they should, when your boiler leaks and if your boiler still has a pilot light.

Breakdowns of boilers are quite common during the winter months and are usually very expensive to repair when this occurs. According to the research carried out recently by uSwitch, repairing a boiler can cost an average of about £314 with a figure over 20 percent of homes experiencing various heating system issues last year.

To answer the question of whether or not your existing home insurance will be enough to cover the boiler breakdown, the answer is probably not. This is due to the fact that heating system faults or breakdowns is a very common occurrence and as a result of poor maintenance practices as well as a high repair cost, several insurance companies often remove it from their home insurance policies.

Generally, you’d be given an option of what is termed as “emergency home cover which is an add on or extra to your home insurance policy. Luckily, this add on is quite inexpensive and may be as little as £4 or £5 per month. Depending on your need or budget, you can also purchase the add on as a “stand alone from your current insurer or another company. However, the standalone option is usually more expensive.

The emergency home cover normally provides coverage for the boiler repair cost and few times, the rest of the central heating system as well. Being fully aware how important a boiler can be, insurance companies usually deliver a rapid response service as suggested in the name, “emergency home cover. However, the maximum pay-out for call out charges is capped at a particular amount which usually ranges from £500 and £1,000. Apart from the call out fees, the emergency cover also includes a limit on the pay-out amount for future required repairs of heating systems which includes both parts labour.

What Is The Best Oil Boiler On The Market?

With a plethora of sizes and models available in the market today, it can be a hassle choosing the best oil boiler. There are 3 main types of oil boilers which includes an oil combi boiler, a regular oil boiler and a system oil boiler. Within these three types, we have a wide range of models and sizes with varying heating and hot water demands.

With tonnes of oil boiler brands out there, the problem is the over crowding on the market with oil boilers that are not only over priced, but also of mediocre quality. From our research, we’ve been able to identify three major bands that are simply outstanding - Warmflow, Grant and Worcester Bosch. However, out of the lots, Warmflow is simply the most efficient and also comes with several qualities such as :

lUK & Ireland’s only AA rated combi boiler

lMarket leading innovation

lEasy and simple to install

l45plus years heating homes

l5 and 7 year warranty available

The oil boiler comes with an outrageous 5 year warranty on their Titanium which when compared to some similar Worcester Bosch Oil boilers is a whooping 3 years difference. Furthermore, the brand also offers a special “out-of-the-box 5-year warranty which enables the warranty to be valid as long as the installation is done by a qualified oil boiler technician. This may, however, seem normal until you realize other brands like Grant, will only honour their 5-year warranty when the boiler is installed only by their accredited technicians.

Warmflow offers an oil boiler to suit every property that is situated off the grid. These includes the modern and stylish U-Series, outdoor-compatible K-Series as well as the quietly efficient B-series which is designed for indoor installation.

Biomass boilers will work with existing central heating systems, presuming this is not decades old, whether they use radiators or under floor heating. A surveyor will check the existing system you have in place before quoting for or recommending a biomass boiler to you.

Can I Repair My Own Gas Boiler?

If you’re more of an handy person, then you’d probably want to fix everything you can around the house while saving yourself some money that would have been spent on hiring a professional instead. This is a very cost effective but at the same time you must know that some tasks are usually more difficult than others, and a good example of those complex tasks is boiler repair. Not only can this be very tough, but they can also potentially be one of the most dangerous home appliances you can acquire. So with that in mind, what can be done to ensure your gas boiler is taken care of and in the event whereby it starts to malfunction, what can be done to remedy the situation?

With regular maintenance and repair of your gas boiler, you’d have absolutely nothing to worry about. However one of the fear several DIYers have is the fact that they might just end up incurring more expenses on services they didn’t really need in the first place. But when it comes to gas boilers, it’s necessary to be certified to work with them as it’s very dangerous to tackle it all by yourself. Despite this, there are still some minor issues that you wouldn’t need to hire a technician to resolve. In some cases, all that would be needed is simply to reset the boiler. To identify where the reset button is, simply go through your boiler’s manual for more information. Most times, all you’ll have to do is press down the reset button for a couple of seconds. If the boiler isn’t fully restored to its normal proper functioning state after two resets, then you may need to call in a professional for help.