Find a Heating Engineer you can trust in St Bees.

How To Fix A Broken Boiler

To fix any problem when it comes to home appliances, the first step is always to identify the problem while also carrying out thorough checks - a broken boiler is not an exception. Putting enough time and effort in diagnosing a problem can go a lot way to save you both time and money. So here are some of the steps you can take to fix your broken boiler before you put a call out to a licensed engineer.

✓ Check to confirm if your pilot light is on. Whenever you’re facing some issues with your boiler, this should always be the first thing you do. The pilot light being on speak volumes, if the light is off then there’s absolutely no way the flame can start the appliance’s gas supply. You should try to put it back on, if off. To do this, you simply have to follow the detailed instructions on your boiler’s manual strictly. If after following these actions to the letter and the issue remains the same, then you’d probably need the services of an a qualified engineer. Never try to fix the issue on your own.

✓ Check the pressure. The solution to the headaches might sometimes be as simple as examining your appliance’s pressure gauge. Here, the good numbers are around 1.0 or1.5, if it happens to fall below this, then you should open the boiler’s instruction manual. You can also inspect your radiator valves for any leaks. You’d have to call in a specialist to solve the issue.

✓ Check the thermostat. Here, it’s important to note that a faulty thermostat doesn’t necessarily imply a broken boiler. It may just signify that you need to replace your thermostat. Simply check to ensure that your thermostat is turned on and temperature is at the appropriate degree.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

• Switch off your boiler and let it cool completely

• Make sure both ends of your filling loop are attached

• Open both valves to allow cold water into the system – you’ll hear it start to move

• Look out for your pressure gauge to show 1.5 bar

• Close both valves

• Switch your boiler back on

• Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

If you’re building a connected home, a smart thermostat allows you to change the temperature in your home. And not only do several smart thermostats come with touch screens and a user friendly interface, but they’re also compatible with Amazon Alexa, Google Assistant and other voice controlled personal assistants. So how does a smart thermostat work? Let’s have a look!

Generally, smart thermostats are connected to the home’s Heating and/or Air Con system via C wire (common wire). Homes that lacks a C wire (especially older homes) will have to install one first before getting a smart thermostat. The C wire is a crucial element in the installation process as it works mainly to wire your smart thermostats into the Boiler system without tampering with the wiring for the other appliances in the house.

The smart thermostats comes with some special temperature setting which you can access by connecting them to your home’s WiFi. These include:

• Mobile Control

Most smart thermostats are specially designed to enable users to control the temperature of their home from the comfort of their couch or car via their unique mobile apps. This feature is just perfect if you particularly like getting the perfect temperature in your home without having to get out of bed.

• Humidity Controls

Although, the humidity of your home can not really be adjusted with a smart thermostat but you can always stay on top of it by monitoring it or setting an alarm on your phone to go off when the humidity changes.

• Geofencing Feature

With a smart thermostat, you can choose the particular times of the day you want it in action. This feature enables you to go on impromptu travels without having to worry about your energy bills - some smart thermostats come with the geotracking feature which determines when you’ve left the house and adjusts the temperature of the home accordingly with your energy usage in mind.

Are Electric Radiators Expensive To Run?

Just like many home additions, the running costs of electric radiators varies largely on a number of factors. Great number of electric radiators typically comes with an in built thermostat which is designed to turn itself off automatically when not in use in order to save energy.

However the energy provider’s set electricity charge tariff will also have a great influence on an electric radiator’s running cost. Let’s take a look at the running costs of an electric radiator!

A 600 Watt electric radiator ( on a standard electricity tariff) will usually have a running cost ranging between 4 to 6 pence each hour. However you should also take note that this scenario might change in situations whereby the electric radiator is not calling for heat the full 60 minutes of each hour. And this is more likely to be the situation as the thermostat is programmed in such a way that enables it to turn itself off immediately there’s an achievement of your required room temperature level - usually within 10 minutes from the time it was switched on. As a result of this, the running cost per hour of electric radiators will be greatly reduced to just about 1 to 2 pence.

It’s also important to note that enhancing the insulation of your home can go a long way to add to the heat retention value of each room. Consequently, the duration at which the electric radiator calls more heating will be significantly reduced, which in turn, implies a lower electricity bill.

Another key factor that can play a huge role in saving on your heating bills is the programming as well as usage of your electric radiators. Every radiator comes with an independent digital thermostat with a number of 24/7 programming options to help achieve maximum efficiency. When the radiator is properly set according to your lifestyle, you can save as much as 50 percent on your heating bills.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

Ad hoc visits from your engineer to fix small issues with your heating system may actually seem cheaper and a lot more affordable, however when a boiler is ripe enough for a change these small issues are always never ending. Over some period of time, these small issues will inevitably get worse and the idea of “mend and make do will be an absolutely false economy. The best course of action in this sort of event is to find a replacement boiler to install as soon as possible. In this article, we’re going to give you some hints that’ll show you when your boiler needs to be replaced. Now let’s take a look!

✓ Insufficient hot water. Here, you’ll have to check the size of your hot water cylinder. It’s crucial to make sure that your boiler is rightly sized to power your heating as well as hot water circuit in line with your demands. You should always seek the advice of a heating expert who can recommend whether to fix or replace the boiler.

✓ Strange noises. It’s normal for components of the boiler to become worn or damaged over time. Replacing the particular component that’s causing the knocking or rattling may seem cost effective at first but more often than not, the noises usually signal a bigger issue which is likely to build up over time. Hence, it’ll be a lot more logical to replace the boiler itself.

✓ Regular repair of your boiler. It’s essential to have your heating system serviced by a Gas Safe engineer on an annual basis. However, when you have to call them more often than once a year for your yearly maintenance, it may be a wise decision to consider getting a replacement.

✓ Other events whereby you may need a new boiler includes when you can’t get the right temperature in your room, when the radiators don’t heat up as they should, when your boiler leaks and if your boiler still has a pilot light.

Are you worried about blocked drains? Yes, you probably should! As a homeowner ( with a detached, semi detached or terraced house), all plumbing and drainage issues within your home or even within your property boundary is your responsibility. Hence, you’d might want to consider getting a Homeserve plumbing and drainage cover to help keep your home running smoothly and putting your mind at ease. The only exception here is if the drain in question is a lateral drain which is a common feature in flats. In this situation, it’s only the building managers that would be responsible for the maintenance of the drainage as it’s shared between several homes. Before 2011, the various flats or houses that shares the lateral drain are responsible for its maintenance.

Working with top utility companies for over 2 decades, Homeserve has positioned itself as one of the leading home assistance providers in the United Kingdom. With their top notch services, they’ve been able to make their client’s lives a lot easier and stress free through the provision of a wide array of repair solutions such as drainage, plumbing, heating, electrics and a lot more.

As a homeowner with the responsibility of maintaining the drains and ensuring there’s no block or damage, it’s simply a no brainer to go for a plumbing and drainage cover and more importantly, get good cover. Homeserve are one of the providers but there are a number of others which offer great service at competitive prices. Without an insurance in place, you may just have to break the bank just to have an engineer or plumber to fix any plumbing or drainage issue you might have. So why not give yourself a peace of mind and get a cover today?

A terrible day would be walking into your home to discover your boiler is broken - nobody prays for that and even more so, when you’re fully aware a broken boiler can be one of the most expensive things to repair. However, when this occurs, a boiler plan is ready to help cover the repair cost - and that’s only if you’ve gotten one. Generally, cover plans feature only a monthly price which is quite affordable when compared to paying a huge lump sum at once. Furthermore, depending on your cover level, you may not be required to incur call out charges or any other expensive services rendered. And in the event whereby your boiler can’t be repaired, there’ll be plans in place to get a replacement unit. As a result, getting a boiler cover is a great way to give yourself a peace of mind and see to it that you’re not left in the cold when the worse happens.

So the answer to whether or not you should get a boiler cover is totally a positive one. The purchase of a new heating system can be quite costly, but it would even be costlier when you have to repair it ceaselessly throughout it’s service years. With several modern combi units being a complicated heating system to repair, getting a cover plan with unlimited call outs, zero excess as well as cover parts and labour would be a truly wise decision.

In addition, an annual service of your heating system is required by manufacturers in order to make the warranty valid. Therefore, just a basic service plan is very crucial if you do not buy the idea of having to fork out at least £70 for each service.