Find a Heating Engineer you can trust in Glossop.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

Do British Gas Service Oil Boilers?

Are you interested in finding out whether or not the British Gas service oil boilers? Well, you’ll find the answer in this article! The British Gas engineers are able to repair several types of boilers such as home based combi, conventional as well as system boilers. Unfortunately, they do not fix oil boilers, electric boilers or solid fuel boilers, but if you possess a gas boiler that’s more than 70kW which is mostly present in commercial premises or large buildings you can give them a call.

For a yearly boiler service British Gas engineers will provide the following solutions to ensure central heating and boiler are both in proper working condition and also absolutely safe.

• Inspection of your boiler for possible leaks and corrosion.

• Detach your boiler casing to ascertain the proper functioning of it’s main components.

• Clean up all parts as necessary

• Attach the casing back to the system and make sure its well sealed

• Inspect the level of the gas pressure to ensure that it’s at the right level.

• Perform a flue check to determine that the are no toxic gas emissions like carbon monoxide being discharged by your heating system.

Upon completion of the annual boiler service, the British Gas qualified engineers will then drop a checklist with you which is going to include all the relevant information you may want to know about your boiler system.

In some cases, British Gas engineers may be able to complete the entire boiler service in one visit. However, it all depends on the problem that’s discovered (if any). They may not possess the required part to fix the problem with them, so they’ll have to order it from the British Gas national distribution centre. Most times, this part will get to them the next day so they can finish their tasks as soon as possible.

To ensure your boiler is functioning efficiently and to keep your home warm, it’s important to see that your boiler is serviced on a regular basis by a licensed boiler engineer. Failure to do this can result in sudden boiler breakdown which can be a hard hitting blow to one’s financial power especially when there’s no boiler cover to cushion the blow or totally avoid it all together.

When your boiler is covered, it implies that you’re protected in the event whereby your boiler or it’s controls malfunctions or break. Several boiler cover will include the servicing cost, while some may not so it’s advisable to always go through the details, no matter how small, before entering into a boiler cover agreement. Typically, a boiler cover will cost between £60 to £100 per year and the payment is made on a monthly basis. Various boiler insurance companies have varying cover cost, however, here are the common boiler cover policies:

• Homeserve charges from £13 per month

• EDF Energy costs from £13.29 per month

• British Gas from £12 per month

• Scottish Power from £13.13 every month

• CETRI UK charges from £13.50 every month

• 24/7 home rescue costs from £9.60 every month

• Gorgi Home Plan costs from £6 per month plus 3 months free

• Your repair charges from £9.60 per month

• NPower Boiler Cover costs from £10.92 every month

• SSE Boiler Breakdown Cover charges from £4.95 every month

It’s important to note that sometimes you have the option of adding your boiler cover to your existing home insurance, if you do not want a standalone policy for your boiler cover. In many scenarios, this is referred to as an extra or add on service referred to as “Home Emergency Cover. When compared to the standalone boiler policies, this is usually a lot cheaper as it comes in around £5 per month.

How Much To Install A Gas Cooker?

Gas cooker is gradually becoming more and more popular in the UK, with several homeowners looking to have one installed in their various homes. Whether you’re planning remodelling, conversions or perhaps you own a new building, gas ( be it a natural gas or Liquid Petroleum Gas - LPG) is now the favourite mode of cooking ,heating as well as warming across the country.

The fact that it’s popular, however, is not an excuse to install a gas cooker by all means in order to reduce the cost. When it comes to gas cooker installation, adequate care must be taken to ensure costly errors which can lead to fire outbreaks and other dangers are avoided. Therefore, if you’re thinking about getting a gas cooker installed in your home, hiring a qualified gas cooker installation company would be your best bet.

Prior to the installation of your gas cooker, the gas plumber will confirm whether or not your home is connected to the mains gas supply. In the absence of a connection, you’ll have to request for a new service connection. Immediately the connection is available, the certified gas cooker installation company can then proceed to fit in the appliance.

However, for a free standing gas cooker, the measurement of the gas cooker’s dimension will be taken by the fitter as well as the available space for the installation in order to determine whether or not the gas cooker will fit in. After this, the next step would be to turn the gas cooker on its side and fit in the underpins. The gas pipe will then be connected to the manifold while also activating the gas and checking for possible leakages. Once done, the gas would be plugged into the outlet and a test will be conducted on the gas to ensure it’s running the way it should.

The Oil Firing Technical Association or OFTEC operate a competent persons scheme to certify installers. It’s always recommended to use an installer with this certification as it proves they have the training and expertise to properly install your boiler and give you realistic advice on the efficiency of your system. Also, OFTEC registered installers offer Workmanship Warranties to protect you if there are any problems after installation.

No. You must never repair your own boiler – only a Gas Safe-registered engineer can do any work on your boiler. You can do simple DIY tasks to repressurise your boiler or stop a leak, but if you have to remove the outer casing of the boiler or touch the flue then you must get a qualified boiler engineer to take a look at your central heating system.

How Much Is A Gas Safety Certificate?

If you’re a landlord in the UK, then you’d know a gas safety certificate is a legal requirement. If yes, then you’d probably like to know how much it’ll cost to get a gas safety certificate so you can make plans on obtaining one for your property. In this article, you’ll find all you need to know about the amount you’re expected to pay for a gas safety certificate in the UK.

First and foremost, let’s look into the use of the certificate. Basically, a gas safety certificate is the legal inspection of your property’s gas appliances which would be done on an annual basis. Only an approved Gas Safe engineer is allowed to carry out this statutory check. Ultimately, if you own rental properties in the country, this is a requirement you can’t afford to overlook to ensure the safety of your tenants.

Furthermore, included in this inspection are each and every gas appliances, chimneys, pipework as well as flues in the property. In recent times, several individuals make use of fewer gas appliances which ultimately implies that they may only need the servicing of their gas fire. Once you’ve passed the inspection, you’ll be given your CP12 certificate which must be kept for a minimum of two years. A copy should also be provided to your tenants within 28 days of issue. So how much will it cost to get a gas safety certificate?

Depending on your location in the UK as well as the number of gas appliances incorporated, the average cost of a gas certificate will range between £60 to £90. The Gas Safe engineer will carry out the task as a fixed and statutory job.

In recent times, home and property owners are constantly looking for ways in which to enhance both energy efficiency and sustainability especially as the world draws closer and closer to energy-efficient technology. The Nest thermostat is a great example of this fact as its designed in such a way to save energy while also cutting heating and cooling costs. And an interesting fact is, you’re not limited to using just a single Nest thermostat in your home as multiple of the device can successfully run together to maintain a consistent level of temperature monitoring as well as energy efficiency. What’s more? You can add up to 20 Nest thermostat and 18 temperature sensors in a home.

It’s very unlikely that you’re going to need this many thermostats in your home, but if you’d like to add a second the process is quite straightforward. However, we’d recommend you employ the services of a seasoned professional especially if you lack the required training or experience to pull this off to save yourself some time and money.

To get started, simply download the associated Nest app to add Nest devices. Now let’s have a look at the processes involved in adding a second Nest thermostat to your home.

• Open the app.

• Go to the top left corner of the main screen and click on the menu button.

• Pick the location or home you’re adding the device to.

• Go to the top right corner and select the “settings.

• Once done, then click on the Add Product “Plus button.

Upon a successful addition of the second thermostat, the app will guide you through the initial set up steps. Google also offers a very helpful guide if you’re unfamiliar with the initial configuration.