Find a Heating Engineer you can trust in South Molton.

To ensure that your boiler is safe and operating efficiently, it’s essential to have it serviced on a regular basis.

Generally, a boiler service will deliver a wide array of benefits which includes the opportunity to identify safety issues like a possible leak of carbon monoxide, efficient use of energy and reduction in energy bills, prevention of breakdowns, a valid warranty when the boiler is serviced regularly by a qualified engineer as well as an extended lifespan. So what exactly does a boiler service cover? This guide will give you a good insight as to what happens during that service.

Before we get started, it’s very important to note that the work done is always as good as the engineer you employ. Therefore, it’s advisable to make sure your preferred engineer is qualified before proceeding with the service. Below are some of the basic practices the engineer may perform during their visit.

• Thorough Inspection

During the visit, the engineer will carry out a detailed examination of your boiler to ensure it still meets the current standards while also making sure that there are no leaks or corrosion. What’s more? They’ll also examine the boiler’s flame for any faults.

• Boiler Casing Removal

The boiler casing will be detached to check all components and ensure they’re free from all forms of dirt and see to it that they’re all working just as they should. This will include examination of the heat exchanger, main injector, burner and spark probe.

• Flue Examination

The engineer will inspect the flue terminals to make sure there are no form of obstructions and it’s also safely installed.

• Gas Pressure Examination

This is done to make sure the heating system is operating at the right pressure.

Installing your Nest thermostat may not be as easy as screwing a light bulb, but we can also assure you that it isn’t very difficult either. However, if you lack the needed training or experience to pull it off, we’d recommend you hire the services of a professional in order to save yourself some time and money. This guide will give you some quick and easy steps to follow and ensure you make no errors during the installation process.

Once installed removing the Nest Thermostat can be done. To get started, you’ll need just a Philips head screwdriver which Nest has thoughtfully provided with the device.

• Turn off the Nest Thermostat by switching the circuit breaker to the off position.

• Label or mark your old thermostat’s wires. However, if you notice your thermostat is tagged 120v or 240v, or possesses thick wires, do not connect the wires to the Nest as you have a high voltage system.

• Uninstall the old thermostat by locating detaching the wires coming out from the wall into the thermostat. Once done, simply unscrew the device from the wall

• Mark the spot of your thermostat. Do this by threading wires through the Nest base plate’s centre incorporate the tiny bubble level. Once done, you can then use a pencil to mark te two screw holes.

• Attach the trim plate. If you wish to cover the screw holes, simply install the trim plate in the Nest box’s bottom to the base plate.

• Using the screws and screwdriver, attach the Nest base to the wall.

• Connect the wires to the Nest by putting the labelled wires in the Nest’s corresponding ports.

• Put the Nest display by lining up the connector on the display’s back.

• Turn on the power by switching the circuit breaker to the on position

• Connect your Nest thermostat to the WiFi network.

• Follow the on-screen guide and set the temperature.

• Use your smartphone or tablet to download the Nest thermostat’s mobile app to monitor and control your device remotely.

How To Fix A Boiler

A boiler is subjected to regular usage, working for a several hours a day and providing hot water for shower on a daily basis and even more so during winter. With it’s power and efficiency, we tend to postpone or even totally overlook its maintenance. However, no matter how good your boiler is, it consists of many moving components and it’ll certainly develop some faults some day. When the inevitable occurs, you might want to save some money and get it fixed all by yourself.

When it comes to fixing boilers, seeking help from a licensed heating engineer is usually the best solution, however at times you might be just lucky to be faced with minor issues which you should be able to handle yourself. In this article, we’ll look at some of the most common causes of a broken boiler and how you can get your heating system up and running again. Let’s have a look!

✓ Low system pressure. In the event whereby your boiler display a low system pressure, it could mean that the system is about to breakdown. You’ll have to carry out regular inspections on the pressure gauge to see if there’s any noticeable changes and call in a heating engineer immediately to prevent a system breakdown from happening.

✓ Poor heat production. Although this is unlikely to lead to any great issues, but it’ll reduce the effective functioning of your heating system. To prevent a debris build, it’s important to have your boiler cleaned regularly.

✓ Strange noises. Boilers often make noises, so there’s nothing to worry about unless it’s a banging or whistling noise that’s very odd , then there may be a serious issue. You’ll have to check the air intake, pressure, exhaust and piping to ensure they’re working just fine, if not there may be a need for replacement.

How Much Does A Boiler Repair Cost?

An annual service for your boiler might not seem important and may be easy to postpone to another day, but when it happens to breakdown due to lack of adequate attention, this can be quite painful and also costly.

Before you start thinking about the cost of repairing your boiler, the first thing you’ll need to confirm is whether or not your boiler is still covered by the manufacturer’s warranty. You’d be amazed some warranties can last for as long as 12 years, if yours is still on then you can save yourself a huge amount of of money on your boiler repair. As a result, it’s always crucial to keep the details of your warranty somewhere safe, so you can read them from time to time. You never can tell when the rainy day will come!

Most boiler warranties will require your to get your boiler serviced on an annual basis by a licensed and qualified technician. The cost of an annual boiler service is affected by the time of the year you wish to get it done. When boilers are less useful during the summer months, an annual service is usually relatively cheap when compared to the cold months. Around this period, a boiler service will normally cost within the range of £100 to £150, however for a more accurate quote it’s advisable to contact a couple of professionals and compare their quotes.

The cost of getting a boiler repaired will be affected by a couple of factors including your boiler’s make, the age of the boiler as well as your location and how urgent you need it done. If you have a dead boiler, the cost will typically range from £96 to £348 and a boiler displaying a fault code will cost within the range of £90 to £275. Generally, repairing a boiler will cost within the range of £90 to £400 based on the several factors stated above.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

How Can I Get My Oil Boiler Repaired?

Did your oil boiler just broke down and you’re considering your repair options? Well, you’ve come to the right place! Whenever your oil boiler breaks down, you have two options - repair it yourself or get in touch with a reliable professional. If you lack proper training or experience when it comes to fixing of oil boilers, we’d recommend that you rather hire the services of a trustworthy oil boiler engineer who can guarantee the best results while also saving you time and money that could result from possible costly errors.

However the issue is, not all oil boiler repair services are created equal. The words “expert and “professional are now so cheap that almost, if not all oil boiler repair companies online today make use of those words to qualify themselves. However, when several of them are done delivering their oil boiler repair services you’ll have no other choice than to start questioning their claimed status. In order to separate the boys from the men very early on, a little caution and some research is all that’s needed to know the most reliable company to approach.

To get a good repair company, the first step would be to make sure the company is fully accredited with a professional certification scheme so as to be sure that they’re actually qualified to deliver the service.

Another step you can take is by requesting personal recommendations from family and friends. For a company to be referred by several homeowners in the local area then it must be doing something that’s worth the money invested.

You can as well make use of the internet to get a reliable oil boiler repair company. You can start by visiting the website of the company that manufactured you appliance to identify any recommended repair companies. Go through the companies’ testimonials but do not rely too much on them because in several cases they may not be authentic.

How Much Do Electric Radiators Cost?

If there’s an age-long question that doesn’t seem to go away any time soon it’s how much do electric radiators cost? Although it would be perfect to offer an exact figure you can actually work with as the cost of running your heating system, but unfortunately you’ll have to consult a clairvoyant individual to get that. The question is almost synonymous with asking to know what your utility bill will be this month or the next. This is an answer that’s specific to each household, so it would be impossible to provide an answer that applies to all households in the UK. This is because there are several influencing factors that affects what the final cost of your household’s electricity bill will be. Let’s take a look at these factors!

• The size of the room you want to heat. As you would have guessed, the larger the room, the higher the amount of energy that’ll be incorporated, which means a greater electricity bill.

• The age of your house. There’s a high possibility your household ( if it’s an old one) lacks sufficient insulation which makes it less energy efficient, except you’ve already made some necessary changes.

• Your individual needs. Depending on your personal requirements, you electricity bill may be greatly influenced to be higher or lower. And the more people you have in your home, the more the energy you’re likely to consume.

• Time of the year. During the winter months, you’re likely to use a lot more electricity and heating because the weather tends to be colder.

• Your property’s exposure to natural elements. For instance a terraced home with houses on either side will be able to retain heat much longer and there less electricity and heating than a fully detached home.

If you’re looking for a reliable or reputable source for your new gas boiler, you definitely won’t find much better than British Gas. Using a big firm like British Gas comes with a plethora of benefits , but of course there are also some drawbacks, with the boiler prices being the main one and biggest turn off for most homeowners. However, just before we delve straight in to the price, let’s look at a thing or two about the big company.

The company, “British Gas are not a boiler manufacturer as you probably would have first imagined. They’re actually a company that specializes in the installation of boilers. As a result, they’re able to install just about any type of boiler you can imagine from any manufacturer. Be it a Worcester Bosch Greenstar 8000 Style or a Baxi 600, they’re able to provide you with the cost of having these boilers installed in your home or property.

Combi boilers are perfect boilers for space-saving and this makes them very popular on the market. They’re also very efficient when it comes to heating water instantly and warm your in few minutes. The price of a new British Gas combi boiler varies on a number of factors. Generally, the installation prices of combi boilers start from £1,800. Therefore, if British Gas are to be competitive with their pricing it should also be around this price.

However, if you have a large house with several rooms with a higher demand for hot water, British Gas will most likely recommend boilers such as Worcester Bosch 440CDi and the likes. Judging from other firms in the market, the price to have these types installed should be in excess of £3,000.