Find a Heating Engineer you can trust in Winkleigh.

How To Fix A Broken Boiler

To fix any problem when it comes to home appliances, the first step is always to identify the problem while also carrying out thorough checks - a broken boiler is not an exception. Putting enough time and effort in diagnosing a problem can go a lot way to save you both time and money. So here are some of the steps you can take to fix your broken boiler before you put a call out to a licensed engineer.

✓ Check to confirm if your pilot light is on. Whenever you’re facing some issues with your boiler, this should always be the first thing you do. The pilot light being on speak volumes, if the light is off then there’s absolutely no way the flame can start the appliance’s gas supply. You should try to put it back on, if off. To do this, you simply have to follow the detailed instructions on your boiler’s manual strictly. If after following these actions to the letter and the issue remains the same, then you’d probably need the services of an a qualified engineer. Never try to fix the issue on your own.

✓ Check the pressure. The solution to the headaches might sometimes be as simple as examining your appliance’s pressure gauge. Here, the good numbers are around 1.0 or1.5, if it happens to fall below this, then you should open the boiler’s instruction manual. You can also inspect your radiator valves for any leaks. You’d have to call in a specialist to solve the issue.

✓ Check the thermostat. Here, it’s important to note that a faulty thermostat doesn’t necessarily imply a broken boiler. It may just signify that you need to replace your thermostat. Simply check to ensure that your thermostat is turned on and temperature is at the appropriate degree.

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.

How Often Should You Service An Oil Boiler?

If you have an oil boiler, you probably know the importance of having it serviced to ensure its proper functioning, prolong its useful life as well as ensuring the safety of your home. However, the question that most frequently arises is how often would one need to service the prized hating system? If you’re also looking for the answer to this same question, then you’ve come to the right place. To make sure your oil boiler is running smoothly, safely and efficiently, it should be serviced as often as once in a year. You certainly do want to know the numerous disadvantages of failing to service your boiler. Not only will neglecting your oil boiler service result in possible faults as well as higher energy bill caused by its inefficiency, but can also lead to your warranty ending early.

Therefore, you should ensure your oil boiler is serviced by a qualified heating engineer on an annual basis to make sure it’s running just as it should. This will give you peace of mind knowing you wouldn’t be spending huge bucks on possible repairs and in some cases, replacements.

As a landlord in the UK, it’s a legal requirement to make sure that your oil boiler and flue system is services on a yearly basis in your rental property.

Unlike a gas and oil boiler, an electric boiler do not require the same level of maintenance or servicing. However, it’ll be a nice move to ensure that it’s also checked once in a while.

Overall, it’s important to note that failure to service your oil boiler on a yearly basis can give rise to multiple risks. These includes a rise in energy bills, carbon monoxide leak, fault that can cause boiler breakdown as well as an expensive repair or replacement bill.

When it comes to gas boilers, this is one of the most frequent questions that always pops up and for a good reason. When you invest a considerable amount of money to acquire and install a gas boiler in your business property, it’s only reasonable not only to expect the boiler to warm up your property efficiently, but also to do so for a long period of time. If you’ve just bought or about to get a new gas boiler, it’s likely you won’t have to worry about getting a replacement for a lengthy period of time. Several commercial gas boilers will last for anywhere between 10 to 15 years on the average. However in the event whereby you have an existing one that’s fast approaching the end of it’s useful life, then you should know the time go get a new gas boiler is just around the corner, and the earlier you make the purchase, the better (to avoid any surprise breakdowns that’ll leave your home super uncomfortable).

Just like any other home appliance, it’s a fact that an older gas boiler ( especially those that have been installed over a decade ago) are significantly less efficient that the new modern ones. When the older versions were manufactured is a completely different time to now as both technology and climate concerns are wide apart. So when your existing boiler is approaching the end of it’s useful life, it’ll be wise to start saving up to cover the cost of getting a new one. However, if it’s only about 5 years ago your boiler was installed, it’s highly likely to still be very efficient.

Your LPG storage tank should have a gauge that shows you how much fuel it has in it. Most LPG suppliers suggest that you arrange a fuel delivery when the level in your tank gets down to about 20%. Make regular checks, particularly in the winter when you will use more, so you know when levels are low.

The short answer to this is no! Smart thermostats can still be used without WiFi, however, they’ll be deprived of some certain capabilities and innovative features that comes mainly due to their ability to connect to the internet. As a result, the smart thermostat will only be functional for basic task such as heating and cooling control. In other words, making use of a WiFi connection will be in your best bet to enjoy the multiple juicy benefits that comes with a smart thermostats such as remote monitoring, ability to connect to other devices and display local weather conditions and much more. And what’s the use of purchasing a smart thermostat if you’d not be able to enjoy these remarkable features?

However, even when you have a WiFi, it’s expected for the connection to fail at times. When this happens, what will be the impact on your smart thermostat? Let’s have a closer look!

• As you would have expected, when your smart thermostat is disconnected from WiFi, features that are controlled with the mobile app would all be impacted. And this might be a big headache when you wish to access these features and control remotely when far away from home.

• When your smart thermostat connection to WiFi fails, all live updates and alerts would be affected. This implies that you’d stop seeing updates, reports and notifications on your mobile device. As a result, you’ll not be notified in case of an emergency like electricity cut-outs, water leaks, humidity and temperatures exceeding the set levels as well as thermostat’s low battery.

• The lack of a WiFi connection might have taken away all the juicy advantages of having a smart thermostat, but one function that remains unaffected is the basic one - the control of your home’s heating and cooling system. In other words, if your smart thermostat is offline, your home will still be heated and cooled to the thermostat’s set temperature.

The size of boiler you need will depend on the size of your commercial property, how many radiators and bathrooms you have and how appliances willl need hot water at the same time. The boiler size refers to its output, which is measured in kilowatts (kW), rather than the actual dimensions. Speak to your boiler engineer about which boiler is suitable for you, as if you have more than one bathroom or a lot of people in your home a combi boiler might not suit you.

Ad hoc visits from your engineer to fix small issues with your heating system may actually seem cheaper and a lot more affordable, however when a boiler is ripe enough for a change these small issues are always never ending. Over some period of time, these small issues will inevitably get worse and the idea of “mend and make do will be an absolutely false economy. The best course of action in this sort of event is to find a replacement boiler to install as soon as possible. In this article, we’re going to give you some hints that’ll show you when your boiler needs to be replaced. Now let’s take a look!

✓ Insufficient hot water. Here, you’ll have to check the size of your hot water cylinder. It’s crucial to make sure that your boiler is rightly sized to power your heating as well as hot water circuit in line with your demands. You should always seek the advice of a heating expert who can recommend whether to fix or replace the boiler.

✓ Strange noises. It’s normal for components of the boiler to become worn or damaged over time. Replacing the particular component that’s causing the knocking or rattling may seem cost effective at first but more often than not, the noises usually signal a bigger issue which is likely to build up over time. Hence, it’ll be a lot more logical to replace the boiler itself.

✓ Regular repair of your boiler. It’s essential to have your heating system serviced by a Gas Safe engineer on an annual basis. However, when you have to call them more often than once a year for your yearly maintenance, it may be a wise decision to consider getting a replacement.

✓ Other events whereby you may need a new boiler includes when you can’t get the right temperature in your room, when the radiators don’t heat up as they should, when your boiler leaks and if your boiler still has a pilot light.