Find a Heating Engineer you can trust in Llanelli.

If your boiler is leaking, there are some checks that you can do yourself. However, you should never attempt to repair your boiler yourself – only a Gas Safe-registered engineer should conduct repairs.

There are 3 main reasons why your boiler might be leaking: there’s a pressure valve fault, a temperature valve leak or corrosion in the system. An engineer will be able to spot the problem quickly, but in the meantime there are a few things you can do:

Check the pipe fittings

If your boiler is leaking water around the pipe fittings, it could be an installation fault and you should get in touch with the engineer that fitted it. You can check the pipe fittings by drying the area then waiting to see if the water appears again. If it does, you may be able to do a ¼ turn of the pipe to stop it. However, you should still call the engineer that installed it to ask them to check the PTFE tape on the inside.

Inspect the seals

Over time, the rubber seals on a boiler can start to perish, so if you have an old boiler this could be the source of your leak. If you have a new boiler, it could be caused by your boiler running over pressure.

Heat exchanger corrosion

Unfortunately, if a boiler engineer discovers that the boiler is leaking water from the heat exchanger, this is the end of the road for your system. The heat exchanger is the most expensive part of your boiler, so it makes more financial sense to replace your boiler with a newer, more efficient model rather than try to replace it.

The Oil Firing Technical Association or OFTEC operate a competent persons scheme to certify installers. It’s always recommended to use an installer with this certification as it proves they have the training and expertise to properly install your boiler and give you realistic advice on the efficiency of your system. Also, OFTEC registered installers offer Workmanship Warranties to protect you if there are any problems after installation.

How Much Is A Gas Safety Certificate?

If you’re a landlord in the UK, then you’d know a gas safety certificate is a legal requirement. If yes, then you’d probably like to know how much it’ll cost to get a gas safety certificate so you can make plans on obtaining one for your property. In this article, you’ll find all you need to know about the amount you’re expected to pay for a gas safety certificate in the UK.

First and foremost, let’s look into the use of the certificate. Basically, a gas safety certificate is the legal inspection of your property’s gas appliances which would be done on an annual basis. Only an approved Gas Safe engineer is allowed to carry out this statutory check. Ultimately, if you own rental properties in the country, this is a requirement you can’t afford to overlook to ensure the safety of your tenants.

Furthermore, included in this inspection are each and every gas appliances, chimneys, pipework as well as flues in the property. In recent times, several individuals make use of fewer gas appliances which ultimately implies that they may only need the servicing of their gas fire. Once you’ve passed the inspection, you’ll be given your CP12 certificate which must be kept for a minimum of two years. A copy should also be provided to your tenants within 28 days of issue. So how much will it cost to get a gas safety certificate?

Depending on your location in the UK as well as the number of gas appliances incorporated, the average cost of a gas certificate will range between £60 to £90. The Gas Safe engineer will carry out the task as a fixed and statutory job.

As you would have guessed, the British Gas is one of the leading home assistant companies located in the United Kingdom which delivers a large variety of services to customers and boilers. Basically, they offer four (4) service packages. The first package is an annual boiler service and boiler as well as controls repair. Meanwhile the fourth package (also the largest) combines boiler services with central heating, plumbing, drains as well as home electrics.

Apart from the monthly payment package offerings, customers are allowed to pay on a yearly basis with a large lump sum. If you opt to pay annually, this will help you save some amount of money. There’s also the option of paying an extra £60 to further lower either monthly or annual costs. What’s more? Customers are also allowed to pay an extra of £99 to get either £2.50 for boiler repairs a month or £5.50 for both repairs on boiler and its controls as well as central heating system repairs.

After placing a claim, the repairs required by your boiler would be made within 24 hours. However, in certain cases, there may be some delays as British Gas tend to rate vulnerable customers ( such as elderly persons and families with little kids) higher than the usual ones. All products will include a 24/7 customer support, unlimited call outs as well as a 14 day cooling off period if you choose to remove any service.

In conclusion, British Gas is an affordable and hassle free company offering customers top notch services. Their gas boiler cover include so many juicy benefits you simply can’t afford to miss out on if you have a gas boiler in your home or property.

How Does Electric Central Heating Work?

An electric central heating works to provide a number of benefits for you. These benefits include the following:

lSpace Heating

• The storage heaters work during the night to store electricity which would be used to heat up the heat retaining bricks. This, in turn, will release this energy throughout the day to warm up the room.

• There are also electric radiators which works to deliver on-demand heat and as a result, economy tariffs are totally avoided. It will generate heat by itself rather than storing it and with the controls, you can easily determine the amount of heat to be released when you require it.

• There is the wet electric system options as well which comes with water filled radiators. This operates in a similar way to normal radiators, however, it makes use of electricity to heat up the water.

lWater Heating

• An electric boiler operates in a very similar manner to other boiler types, just that it makes use of electricity as its fuel. Here, the water is warmed by a heating element and the water is later moved to several radiator throughout the house by a pump. These electric boiler types earns you tariff savings as you’ll be able to heat water at night.

• Heat pumps geothermal or air source, redistributes heat instead of creating it. Heat pumps are powered by electricity and it works by absorbing heat either from the air or ground which it then channels it through a pump. This can then be incorporated in heating either water or a room.

• A dedicated immersion heater is another water heating option. Here, the heating element is positioned inside a hot water cylinder. In a similar fashion to a kettle, the element heats the nearby water. Immersion heater can act either as a backup or your main heating element.

If you’re building a connected home, a smart thermostat allows you to change the temperature in your home. And not only do several smart thermostats come with touch screens and a user friendly interface, but they’re also compatible with Amazon Alexa, Google Assistant and other voice controlled personal assistants. So how does a smart thermostat work? Let’s have a look!

Generally, smart thermostats are connected to the home’s Heating and/or Air Con system via C wire (common wire). Homes that lacks a C wire (especially older homes) will have to install one first before getting a smart thermostat. The C wire is a crucial element in the installation process as it works mainly to wire your smart thermostats into the Boiler system without tampering with the wiring for the other appliances in the house.

The smart thermostats comes with some special temperature setting which you can access by connecting them to your home’s WiFi. These include:

• Mobile Control

Most smart thermostats are specially designed to enable users to control the temperature of their home from the comfort of their couch or car via their unique mobile apps. This feature is just perfect if you particularly like getting the perfect temperature in your home without having to get out of bed.

• Humidity Controls

Although, the humidity of your home can not really be adjusted with a smart thermostat but you can always stay on top of it by monitoring it or setting an alarm on your phone to go off when the humidity changes.

• Geofencing Feature

With a smart thermostat, you can choose the particular times of the day you want it in action. This feature enables you to go on impromptu travels without having to worry about your energy bills - some smart thermostats come with the geotracking feature which determines when you’ve left the house and adjusts the temperature of the home accordingly with your energy usage in mind.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

1. Switch off your boiler and let it cool completely
2. Make sure both ends of your filling loop are attached
3. Open both valves to allow cold water into the system – you’ll hear it start to move
4. Look out for your pressure gauge to show 1.5 bar
5. Close both valves
6. Switch your boiler back on
7. Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

How Can I Get My Oil Boiler Repaired?

Did your oil boiler just broke down and you’re considering your repair options? Well, you’ve come to the right place! Whenever your oil boiler breaks down, you have two options - repair it yourself or get in touch with a reliable professional. If you lack proper training or experience when it comes to fixing of oil boilers, we’d recommend that you rather hire the services of a trustworthy oil boiler engineer who can guarantee the best results while also saving you time and money that could result from possible costly errors.

However the issue is, not all oil boiler repair services are created equal. The words “expert and “professional are now so cheap that almost, if not all oil boiler repair companies online today make use of those words to qualify themselves. However, when several of them are done delivering their oil boiler repair services you’ll have no other choice than to start questioning their claimed status. In order to separate the boys from the men very early on, a little caution and some research is all that’s needed to know the most reliable company to approach.

To get a good repair company, the first step would be to make sure the company is fully accredited with a professional certification scheme so as to be sure that they’re actually qualified to deliver the service.

Another step you can take is by requesting personal recommendations from family and friends. For a company to be referred by several homeowners in the local area then it must be doing something that’s worth the money invested.

You can as well make use of the internet to get a reliable oil boiler repair company. You can start by visiting the website of the company that manufactured you appliance to identify any recommended repair companies. Go through the companies’ testimonials but do not rely too much on them because in several cases they may not be authentic.