Find a Heating Engineer you can trust in Polegate.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

How Long Does A Boiler Service Take?

Servicing of your boiler is a very crucial activity which does not only help in keeping your heating system in a top condition, but also assists in ensuring the safety of both you and your loved ones. If you carry out a regular boiler service you’ll be able to identify any possible fault your boiler may have on time before it leads to a more serious issue or even a boiler breakdown. As a result, you’ll be able to save yourself some time and money, but more importantly will save you from any dangerous risk that may result from gas leak in a boiler. The best time for a boiler service is in the summer when you’d probably would not really need the system, so you can take advantage of that as well as the possible lower boiler servicing cost during this period.

Before we look into the amount of time a boiler service should take, let’s first consider what should be done during a boiler service.

✓ Visual inspection. This is a check carried out by the heating engineer to ensure your boiler still meet the existing standards and requirements while also looking for any faults.

✓ Removal of boiler casing. There’s the need to ensure everything is working just fine and also to clean the boiler’s interior. These inspections should include the burner, heat exchanger, main injector and spark probe.

✓ Flue check. This involves making sure that there’s no form of obstructions in the flue terminals as also to ensure that the flue is well installed.

✓ Gas pressure check. This involves making sure that the boiler working with the appropriate pressure.

✓ Boiler fired up. This involves checking for any operating issues.

Generally, a boiler service should be completed within 30 minutes, however this time may vary largely depending on the brand and model.

Are you worried about blocked drains? Yes, you probably should! As a homeowner ( with a detached, semi detached or terraced house), all plumbing and drainage issues within your home or even within your property boundary is your responsibility. Hence, you’d might want to consider getting a Homeserve plumbing and drainage cover to help keep your home running smoothly and putting your mind at ease. The only exception here is if the drain in question is a lateral drain which is a common feature in flats. In this situation, it’s only the building managers that would be responsible for the maintenance of the drainage as it’s shared between several homes. Before 2011, the various flats or houses that shares the lateral drain are responsible for its maintenance.

Working with top utility companies for over 2 decades, Homeserve has positioned itself as one of the leading home assistance providers in the United Kingdom. With their top notch services, they’ve been able to make their client’s lives a lot easier and stress free through the provision of a wide array of repair solutions such as drainage, plumbing, heating, electrics and a lot more.

As a homeowner with the responsibility of maintaining the drains and ensuring there’s no block or damage, it’s simply a no brainer to go for a plumbing and drainage cover and more importantly, get good cover. Homeserve are one of the providers but there are a number of others which offer great service at competitive prices. Without an insurance in place, you may just have to break the bank just to have an engineer or plumber to fix any plumbing or drainage issue you might have. So why not give yourself a peace of mind and get a cover today?

If you get the right size boiler for your business and you get it serviced regularly, your boiler could last up to 15 years. It may even last longer than this, but you’ll find that your boiler begins to become less efficient as it gets older. Also, as technology improves, a boiler older than 15 years may not be the most efficient one on the market.

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.

The simple answer to this question is yes. The Google Nest thermostats are built in such way that makes it compatible with most 24V systems including the older systems. The device is functional with all common types of fuel such as electricity,natural gas as well as oil. However, before purchase it is vital to determine if your thermostat is also compatible. What’s more? The Nest thermostats is also designed to be usable even without the existence of a C wire (common wire) in your home, although a new C wire installation may be required.

Furthermore, Nest Learning Thermostat is compatible with multiple central heating system such as combi boiler systems, air source and ground source heat pumps (heating only) as well as heat only boiler. Now let’s take a look at the Nest thermostat compatibility!

• The majority of the 24 V systems ( including older systems) are compatible with Google Nest thermostat. They can be incorporated with each and every common types of fuel such as oil, natural gas as well as electricity.

• Prior to the installation of Google Nest thermostat, you can make use of the Google Home or Nest app for proper guidance and to notify you if your system is compatible. It will also give you a bespoke thermostat wiring guide.

• To check the compatibility of your system, you can also check with the Google’s online compatibility checker before purchase.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

• Switch off your boiler and let it cool completely

• Make sure both ends of your filling loop are attached

• Open both valves to allow cold water into the system – you’ll hear it start to move

• Look out for your pressure gauge to show 1.5 bar

• Close both valves

• Switch your boiler back on

• Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

How Much To Install A Gas Cooker?

Gas cooker is gradually becoming more and more popular in the UK, with several homeowners looking to have one installed in their various homes. Whether you’re planning remodelling, conversions or perhaps you own a new building, gas ( be it a natural gas or Liquid Petroleum Gas - LPG) is now the favourite mode of cooking ,heating as well as warming across the country.

The fact that it’s popular, however, is not an excuse to install a gas cooker by all means in order to reduce the cost. When it comes to gas cooker installation, adequate care must be taken to ensure costly errors which can lead to fire outbreaks and other dangers are avoided. Therefore, if you’re thinking about getting a gas cooker installed in your home, hiring a qualified gas cooker installation company would be your best bet.

Prior to the installation of your gas cooker, the gas plumber will confirm whether or not your home is connected to the mains gas supply. In the absence of a connection, you’ll have to request for a new service connection. Immediately the connection is available, the certified gas cooker installation company can then proceed to fit in the appliance.

However, for a free standing gas cooker, the measurement of the gas cooker’s dimension will be taken by the fitter as well as the available space for the installation in order to determine whether or not the gas cooker will fit in. After this, the next step would be to turn the gas cooker on its side and fit in the underpins. The gas pipe will then be connected to the manifold while also activating the gas and checking for possible leakages. Once done, the gas would be plugged into the outlet and a test will be conducted on the gas to ensure it’s running the way it should.