Find a Heating Engineer you can trust in Llanfairpwllgwyngyll.

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.

Smart controls such as Hive are the next generation technology with more and more people now converting their houses into smart homes to control multiple devices in the homes remotely. Smart technology can be incorporated with several household devices such as security, lighting, entertainment and more. But what if there’s an oil boiler installed in your home, can you still connect your Hive with the your heating? Well, simply read on to find out.

The answer to this question is yes, most oil boilers are compatible with Hive and can substitute for either an existing conventional programmer or thermostat. The smart technology works to help derive more benefits from your heating system and they usually come with apps which can be used to control your home’s heating from anywhere with just your mobile device. Hive, however, cannot work to replace the functions of smart oil boiler heating controls to modulate your heating as they only work on an on or off basis. To make use of the modulating technology in an oil boiler, the cost of manufacture would be considerably higher while offering little advantage in efficiency for the home or property owner. Ultimately, this implies that you can’t incorporate smart technology to control the output in a similar way as a gas boiler, but there are still some ways to utilize smart technology with your oil boiler in such a way to boost your efficiency and lessen the energy bills.

Do you want to use your Hive with your home’s oil boiler? We’d advise you get in touch with an OFTEC qualified engineer if you wish to install Hive Active Heating on your oil boiler, as British Gas engineer do not offer this service.

Biomass boilers do require some maintenance. Many manufacturers recommend servicing twice a year, although this is often included in the installation cost. Many systems have automatic fuel loading that removes the need to manually load fuel. You will need to remove the ash from the boiler, but this is as easy as emptying a vacuum cleaner.

How To Get A Gas Fireplace Installed

A gas fireplace is one of the most popular means of adding warmth to homes which so many homeowners have now come to terms with, especially with natural gas prices being fairly low for an extended period of time. Properly installed gas fireplaces are not only capable of adding a much needed ambiance and warmth to your home, but also significantly more efficient than the traditional wood-burning fireplaces which mostly produces less heat from the large amount of drafts they consume. Meanwhile a good gas powered fireplace with a properly functioning blower, is very close to being as efficient as a furnace when warming up a room. What’s more? Gas fireplaces also possess a great visual appeal and are also very practical especially when they feature realistic ceramic logs as well as good gas burners.

Installing a gas fireplace by yourself is definitely up there as one of the most advanced DIY tasks you can attempt to try. If you lack proper training and experience, it’s advisable you leave the task to a reliable professional that’ll guarantee the best results while also ensuring costly errors are avoided. This guide will, however, put you in the right direction.

• Construct wall recess to accept the fireplace.

• Punch a hole through the exterior wall of the house to fit in stovepipe thimble.

• Fix a small part of the stovepipe to the exhaust port in the fireplace’s rear.

• Use construction adhesives on the wall around the fireplace opening’s sides and top.

• Apply granite slabs into the adhesive around the opening of the fireplace.

• Put the fireplace in position and ensure the stovepipe goes outdoors through the thimble.

• Use a termination hood to seal the exhaust pipe’s exterior.

• Employ the services of a professional plumber to connect the gas to the fireplace.

• Fit the removable front

• Test the functionality of the fireplace.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

The size of boiler you need will depend on the size of your home, how many radiators and bathrooms you have and how many people live there. The boiler size refers to its output, which is measured in kilowatts (kW), rather than the actual dimensions. Speak to your boiler engineer about which boiler is suitable for you, as if you have more than one bathroom or a lot of people in your home a combi boiler might not suit you. Other boiler types such as system boilers or conventional boilers may be better suited to larger homes because they have bigger outputs.

To ensure that your boiler is safe and operating efficiently, it’s essential to have it serviced on a regular basis.

Generally, a boiler service will deliver a wide array of benefits which includes the opportunity to identify safety issues like a possible leak of carbon monoxide, efficient use of energy and reduction in energy bills, prevention of breakdowns, a valid warranty when the boiler is serviced regularly by a qualified engineer as well as an extended lifespan. So what exactly does a boiler service cover? This guide will give you a good insight as to what happens during that service.

Before we get started, it’s very important to note that the work done is always as good as the engineer you employ. Therefore, it’s advisable to make sure your preferred engineer is qualified before proceeding with the service. Below are some of the basic practices the engineer may perform during their visit.

• Thorough Inspection

During the visit, the engineer will carry out a detailed examination of your boiler to ensure it still meets the current standards while also making sure that there are no leaks or corrosion. What’s more? They’ll also examine the boiler’s flame for any faults.

• Boiler Casing Removal

The boiler casing will be detached to check all components and ensure they’re free from all forms of dirt and see to it that they’re all working just as they should. This will include examination of the heat exchanger, main injector, burner and spark probe.

• Flue Examination

The engineer will inspect the flue terminals to make sure there are no form of obstructions and it’s also safely installed.

• Gas Pressure Examination

This is done to make sure the heating system is operating at the right pressure.

How To Install An Oil Boiler Heating System

Just like several other skills, the installation of an oil boiler heating system can be a challenge. It requires enough persistence to actually get right, so if you’re the type with little patience, we’d recommend you hire the services of a professional oil boiler heating system fitter who can guarantee the best results and save you time and extra money due to potential damages.

To install your boiler system yourself, it’s always advisable to start by getting the information on the best installation processes from the supplying company which will go a long way to save you from future headaches. However, we’ve put together this guide to give you a basic knowledge on how its done. Let’s have a look!

lRead Instruction Manual

• Carefully read and digest the instruction manual thoroughly.

• Make sure you understand the installation diagrams

• Spread out the materials and get familiar with them.

lFigure Out What Goes Where

• Take your time to determine where everything goes in relation to the others.

• Identify the new radiator’s position.

• Get sufficient sealants to prevent possible leakages inside the walls.

lIdentify The Pipe Routes

• Determine the pipe routes while fitting the new radiators

lInstall The Boiler

• Turn off water and all electrics

• Fit the boiler into the wall

• Make sure the fittings are secured.

lInstall The Radiator

• The effectiveness of your home’s heating system is as good as the radiators you incorporate and how good they’re installed.

• You may have to utilize extra radiators in large open plan kitchens and living rooms (for effective heating).

lOffer Ventilation

• Once you’ve successfully installed the new radiator, a small dose of air ventilation would be needed.

• Turn the key of each valve located at the bottom, do not stop until a little amount of water spills over the top of the unit.